用電趨向

如題, 依家大家用電既趨向仍然係3a ni-mh電定有新趨向?li-fe??

已經試左
快到痴孖根
但最估不到是, 掃左呢件野:

登錄/註冊後可看大圖

可能快到無朋友啊!

tomcheng18 發表於 2013-4-12 17:33

                               
登錄/註冊後可看大圖

這星期日會拿架Buggy試跑一下

拍片上黎睇下

這星期日會拿架Buggy試跑一下

登錄/註冊後可看大圖

kevt2005 發表於 2013-4-10 02:04

                               
登錄/註冊後可看大圖

Good to hear that.  Looking forward to trying it.

听说在努力中。。。期待ING

zx300 發表於 2013-4-9 23:12

                               
登錄/註冊後可看大圖

告诉大家一个好消息，大家在年底前，有机会能测试新型专门的电种。大家请期待。

miniz 爱好者 ...

Good to hear that.  Looking forward to trying it.

jj1985 發表於 2013-4-9 18:43

                               
登錄/註冊後可看大圖

多謝兩位CHING指教,,真係最後一問...咁買R246 2S LI-FE電好,定4 X NI-ZN 好?  R246 要剪位我唔介意...最 ...

No problem.  Happy to share information and experience.
In my tests, NiZn are more powerful than LiFe.  NiZn batteries are very cheap.  You can buy the factory standard Ni-Zn charger,  Not expensive as well.  Check out Taobao.  If you like NiZn and decide to use more, you may consider getting the PowerLab6 or 8 charger.  It's the only charger that I can find on the market so far that supports Ni-Zn charging mode.  But expensive - around $13xx/$18xx.
LiFe is bit more expensive and you have to buy the charging cable or make one yourself.
I'd say you should try both if you consider yourself a curious person like me. 8-)

Feel free to post more questions.  I'm more than happy to share more if it helps.

cptkirk9 發表於 2013-4-9 22:38
LiFe電嘅好處係輕同易揾差機，但容量較少，可能只玩到五分鐘，用無刷可能耐啲！
NiZn就唔洗改車，Volt數高 ...

告诉大家一个好消息，大家在年底前，有机会能测试新型专门的电种。大家请期待。

miniz 爱好者

cptkirk9 發表於 2013-4-9 22:38
LiFe電嘅好處係輕同易揾差機，但容量較少，可能只玩到五分鐘，用無刷可能耐啲！
NiZn就唔洗改車，Volt數高 ...

告诉大家一个好消息，大家在年底前，有机会能测试新型专门的电种。大家请期待。

miniz 爱好者

LiFe電嘅好處係輕同易揾差機，但容量較少，可能只玩到五分鐘，用無刷可能耐啲！
NiZn就唔洗改車，Volt數高所以超快，但難揾差機，就算用一般LiPo / LiFe mode差有可能好快打柴！

kevt2005 發表於 2013-4-9 18:04
Sorry, my computer doesn't have chinese character input now.  You are correct.  I was just trying  ...

謝謝CHING指教.

cptkirk9 發表於 2013-4-8 20:25
I think a charge up NiMh battery will be around 1.4-1.5V so that 6x is around 9V max.
For NiZn, 4x1. ...

多謝兩位CHING指教,,真係最後一問...咁買R246 2S LI-FE電好,定4 X NI-ZN 好?  R246 要剪位我唔介意...最梗要粒電夠勁...謝謝

問題問多了,請不要介意...謝謝

jj1985 發表於 2013-4-8 11:31

                               
登錄/註冊後可看大圖

多謝CHING 詳細回覆,又學到野. 不過我英文唔係咁好, 想再確認一下, MR03 可用4粒 NI-ZN 電?
4粒電壓介乎  ...

Sorry, my computer doesn't have chinese character input now.  You are correct.  I was just trying to be conservative.  Max Charge-up voltage of a Ni-Zn is around 1.907V but it will quickly drop to below 1.8XV as soon as you remove it from the charging rack.  It'll continue to drop to 1.6X and maintain for a long period and then drop sharply at the 3rd stage.
See the attached graphs of Ni-Zn discharging and charging.

登錄/註冊後可看大圖

I think a charge up NiMh battery will be around 1.4-1.5V so that 6x is around 9V max.
For NiZn, 4x1.9 is around 7.6V and still a lot less than 6xNiMh.
So I recommend you not try to use 6xNiMh or you will push it to the limit too soon.

kevt2005 發表於 2013-4-7 20:09
I have not tested the MR03 board to its limit and so I cannot say what's the actual max voltage th ...

多謝CHING 詳細回覆,又學到野. 不過我英文唔係咁好, 想再確認一下, MR03 可用4粒 NI-ZN 電?
4粒電壓介乎 1.6X4=6.4 至 1.9X4=7.6 之間? 都唔會燒板? 謝謝ching!!!

jj1985 發表於 2013-4-7 18:25

                               
登錄/註冊後可看大圖

咁CHING知唔知MR03 Without takiki 塊板最大頂到幾高電壓?用6粒NiHM 得唔得呢?我而家自己改咗,加咗1粒外 ...

I have not tested the MR03 board to its limit and so I cannot say what's the actual max voltage the board can accommodate.  I would recommend you to measure the actual voltage output of your modified battery pack.  Under 6.5V should be OK.  6xNiMh should be something like 1.2V*6=7.2V.  Mind you that 1.2V is the nominal voltage.  Actual can be something like 1.25V per cell and so 6 NiMh will be very likely kill the board even for the latest board and I would not recommend you to even try.  Anyway, if you still want to try, accept the risk and be ready to lose a board.  Good luck.

kevt2005 發表於 2013-4-7 15:47
I have not seen LiPo batteries for Mini-Z on the market yet.  As far as I know and I've seen, for  ...

咁CHING知唔知MR03 Without takiki 塊板最大頂到幾高電壓?用6粒NiHM 得唔得呢?我而家自己改咗,加咗1粒外接電池箱,THX

jj1985 發表於 2013-4-6 11:14

                               
登錄/註冊後可看大圖

Thanks C Hing. 咁想再請教一下, MR03可唔可以用到 2S LIPO, 叉滿2粒LIPO電,會唔會燒板? ...

I have not seen LiPo batteries for Mini-Z on the market yet.  As far as I know and I've seen, for Lithium chemistry, there is only LiFe batteries that fits a MR03 chassis (still requires some modification).  Generally speaking, voltage of around 6V will not kill the board.  Using Ni-Zn as an example, it has characteristics similar to LiPo chemistry and it has nominal voltage of 1.6V per cell (AAA size).  I've tried running Ni-Zn on MR03 stock (without FETs) with PN50T and AD Stock motor without problem.  As a matter of fact, Ni-Zn can actually be charged up to 1.9V.  So, in my tests (not very objective and comprehensive though) the MR03 boards (both with and without TikiTiki mode) should be fine to deal with higher voltage batteries.  However, I would recommend to add FETs though if you would be playing with the car continuously with packs of batteries as Ni-Zn batteries are very hot after playing.
So, back to your question, if you can find LiPo batteries that fits on MR03, the above comments should still hold true.

kevt2005 發表於 2013-4-4 22:44
I'm not sure what's your question.  I'm using AAA size NiZn batteries.  Mini-Z requires 4xAAA.

Thanks C Hing. 咁想再請教一下, MR03可唔可以用到 2S LIPO, 叉滿2粒LIPO電,會唔會燒板?