RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 已经不是新车的XPRESS MRR2 [打印本頁]

作者: SRGOD 時間: 2009-2-7 03:20
標題: 已经不是新车的XPRESS MRR2
买回来是已经装好的，过年前去室内场试车的时候跑了半天都不顺，回家才发现前轮Caster竟然是往前倾的……立刻拆车重装……
前天再去室内场跑感觉好多了～哈哈～动力是EC POWER 60A有感无刷电调+8.5T无刷，4000KV吧，我就完全够用了
感觉此车前上臂结构优点是不用更换零件就能调整Caster角和Camber角，但是这样完全通过推杆调整的话一套调车尺就必不可少了。
还有担心的就是这结构的强度，怎么看都觉得不太放心，不过跑了两次经过我几乎上20次的撞车还没有损坏零件，心满意足了……

今晚还把M04的防撞海绵DIY上去了……

真混乱的布线……
[attach]224474[/attach]

[attach]224474[/attach]

[attach]224476[/attach]

[attach]224477[/attach]

[attach]224478[/attach]

[attach]224479[/attach]

作者: wingx2 時間: 2009-2-7 10:46
师兄在哪裡车场玩?

作者: SRGOD 時間: 2009-2-7 21:59
我響深圳南山個室內場玩，賽道掉頭灣比較多，場地有時會噴下糖水，所以好咬下。依家頭彈簧換左田宮M車TRF避震配果對白身黃標的彈簧，后面用Xpress原裝果對，車頭軟車尾硬的設定，感覺入彎系比較靈活，但仲未夠時間試出有咩副作用之類的。仲研究紧甘噶场地应该点SET部车好

作者: 楓仔 時間: 2009-2-7 22:15
我都想去你個車場睇下....

作者: raymen 時間: 2009-2-27 20:13
C.hing,
HOw big is the Pinion gear you're using in 8.5 TURN ? I feel the car very NOISE when Im using the ECpower ? Is that normal ? And the ESC cannot use 100% Forward speed , I turn it down to 65% speed only..... but the speed similar to 23Turn

THKS.

[ 本帖最後由 raymen 於 2009-2-27 20:14 編輯 ]

作者: SRGOD 時間: 2009-2-27 21:53
I use the SpeedMind 64P 30T gear. And I think my car is not quiet too.

Why don't you set the ESC 100% forward speed? Is the ESC have any problem?

作者: raymen 時間: 2009-2-27 22:24

原帖由 SRGOD 於 2009-2-27 09:53 PM 發表

 登錄/註冊後可看大圖

I use the SpeedMind 64P 30T gear. And I think my car is not quiet too.
Why don't you set the ESC 100% forward speed? Is the ESC have any problem?

IF I set it 100% forward speed , the Belt seems flying...and the car cannot push forward ,because the speed of the motor too fast ... HOw about you ?

I use 64 pitch , Original Spur gear and 40T pinion gear, is that match ???
This car really NOISE

[ 本帖最後由 raymen 於 2009-2-27 22:25 編輯 ]

作者: SRGOD 時間: 2009-2-27 22:44
40T is ok for 8.5T motor. I use 30T pinion gear 100% forward speed and the car accelerate very fast.
Maybe your belt or ball diff have some problem? like the ball diff is too loose? Or try to change a new belt

作者: raymen 時間: 2009-2-27 23:16

原帖由 SRGOD 於 2009-2-27 10:44 PM 發表

 登錄/註冊後可看大圖

40T is ok for 8.5T motor. I use 30T pinion gear 100% forward speed and the car accelerate very fast.
Maybe your belt or ball diff have some problem? like the ball diff is too loose? Or try to chang ...

Yeh....maybe the belt is too loose , but how to make it tight ?

作者: AMAT 時間: 2009-2-27 23:18
XPRESS MRR2有原裝O既XPRESS頭BUMPER的~唔駛DIY咁辛苦~嘿嘿!

作者: SRGOD 時間: 2009-2-27 23:33
You can try this part to tight the belt.

http://www.rcmart.com/catalog/rc ... cPath=595_1075_1076

作者: raymen 時間: 2009-2-28 00:02
Thanks...

[ 本帖最後由 raymen 於 2009-3-3 20:52 編輯 ]

作者: raymen 時間: 2009-2-28 00:49
THank you very much brother..... Really the Ball Diff is too loose, after I tight it more better now....

作者: SRGOD 時間: 2009-2-28 03:46
Don't forget the Ball Diff Grease

作者: raymen 時間: 2009-3-3 20:51
師兄,你覺吾覺轉向比較差?
較得太盡,前面兩個轆又會磨到底板辺, 較得太開的轉向度又吾足?!

作者: raymen 時間: 2009-3-7 15:04
May I know what brand of the Li-Po battery U're using now ? The Maximum is 25C or 30C for the EC power ESC ???

Thks......

作者: SRGOD 時間: 2009-3-8 00:52
轉向我覺得都夠用啊，我較到轉到最盡車胎離底板仲有3mm。試下再SET Camber 角同Caster 角應該可以有幫助

作者: Scania 時間: 2009-3-10 15:24
幾銀？

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)