RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 水冷無水出 [打印本頁]

作者: ChinaBilly 時間: 2009-2-20 12:05
標題: 水冷無水出
各位師兄,

我部船的水冷無水出,各位師兄可否指點我如何解決,現附相作參考.

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

作者: bigboymagic 時間: 2009-2-20 12:57
標題: Re: 水冷無水出
師兄，愚見，似乎個入水太直同位置要修改下...

可参考這裏 http://www.jet-drive.de/cms/content/view/41/25/lang,en/

作者: ChinaBilly 時間: 2009-2-21 16:41
標題: Need help for water cooling
I 'll let you know after I test

作者: GOLDWING1800 時間: 2009-2-22 00:28
kyosho D 船成日都係咁,水泠管入水位去唔到車葉位

可以DIY加支短銅管仔cut斜佢like me!!!(my ship is kyosho airsteam)

: 登錄/註冊後可看大圖

作者: ChinaBilly 時間: 2009-2-26 22:36
標題: 水冷無水出
I extended a3mm long and I tested it in my bath, It seems OK! so Happy, Thank you for your advise....

I will go & try this week!

作者: ChinaBilly 時間: 2009-2-27 08:52
標題: 水冷無水出
With photo,

: 登錄/註冊後可看大圖

作者: GOLDWING1800 時間: 2009-2-28 10:04

原帖由 ChinaBilly 於 2009-2-26 22:36 發表

 登錄/註冊後可看大圖

I extended a3mm long and I tested it in my bath, It seems OK! so Happy, Thank you for your advise....

I will go & try this week!

If u use plastic tube to extend it. I'm worry when the motor full power,the tube will bend woo..
I suggust use a large size of copper tube and use yr way to plug-in will much better!!!

作者: ChinaBilly 時間: 2009-3-2 09:41
標題: 水冷無水出 + speed problem
I tested this Sat. U r right again, when full power the water output is less (slower is better), I will change the copper tube instead. (What size?)

By the way, The speed is getting slower after 3 to 5 times of full power, is that the cooling system problems or Motor issues?

Can you help again?

I am using the hobbywing 9T motor, 60A water cooling Esc and 7.4V 5000mah Lipo battery

作者: GOLDWING1800 時間: 2009-3-3 11:24

原帖由 ChinaBilly 於 2009-3-2 09:41 發表

 登錄/註冊後可看大圖

I tested this Sat. U r right again, when full power the water output is less (slower is better), I will change the copper tube instead. (What size?)

By the way, The speed is getting slower after 3 ...

For the copper tube, its depends on your boat. Just buy one the inner dia. can plug-in is okay.
For my boat's water inlet point dia. is 5mm.
I don't know the problem about the electronic, coz I just play GP boat. Sorry!!!!
But I'll hv a EP boat will a assembly later, I also want to know yr problem too...

作者: ChinaBilly 時間: 2009-3-3 23:58
Thanks anyway!

作者: GOLDWING1800 時間: 2009-3-17 12:09

原帖由 ChinaBilly 於 2009-2-26 22:36 發表

 登錄/註冊後可看大圖

I extended a3mm long and I tested it in my bath, It seems OK! so Happy, Thank you for your advise....

I will go & try this week!

thanks brother of the water inlet point ideal.

I've modify my inlet point as follow:-

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

作者: ChinaBilly 時間: 2009-3-18 22:49
Any improvement?

作者: GOLDWING1800 時間: 2009-3-19 17:38
標題: 回復 12# 的帖子
I havn't try it.....
will tell u later!!

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)