RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: JR PCM9XII [打印本頁]

作者: mkevin 時間: 2006-5-28 19:12
標題: JR PCM9XII
Dear Big Brothers,

I am a beginner to learn how fly the RC Electric Heli. But I have a few questions as belows:

1) I notice that the throttle can be placed at left hand side, is it true ? I read the USA/UK RC Heli
Magazine.
2) But my new RC transmitter is on the right hnad side, can we change it ? I am get used to the left hand side for throttle.

Thanks a lot.

Best regards,
Heli Fan

作者: 小步 時間: 2006-5-28 20:07
你說的是 mode 1 ,mode 2 之分

9x menu有教係點switch mode 1 -> mode2

作者: mkevin 時間: 2006-5-28 21:15
標題: JR PCM 9xII
Sorry, I don't understand. Do you mean to change the mode ? But the stick is not in centre on right hand side.

Thanks a lot

作者: 小步 時間: 2006-5-28 21:55
You need open the CASE yourself and replace the 彈弓同鋼片去右面.

9x 本身就support mode1 to mode4 <-soft setting pls check the menu

作者: mkevin 時間: 2006-5-28 22:34
標題: JR PCM 9X II
Thank your advice.

Best regards,
Kevin

作者: mkevin 時間: 2006-5-28 23:19
標題: PCM 9XII
Is it poupular to use the throttle at the left hand side ? Why are they different ?

Please advise.

Thanks a lot.

作者: zifu 時間: 2006-5-28 23:33
some of jr9x v2 can't change from mode 1 to mode 2. before sold 2 sets can't change. can't open the stick direction.

作者: 小步 時間: 2006-5-29 00:20
mode2 is suitable for extreme 3D flying .Coz Both Aleon and Elevator on same stick

作者: Mazda_6 時間: 2006-5-29 00:53
請問9X II可唔可以用鋰電

作者: zifu 時間: 2006-5-29 02:07

原帖由 mkevin 於 2006-5-28 23:19 發表
Is it poupular to use the throttle at the left hand side ? Why are they different ?

Please advise.

Thanks a lot.

because at usa and europe there model flier would like to control the hobby like the real control stick. one stick can be control aleon and elevator at some axis but the japanese like to control different way

作者: zifu 時間: 2006-5-29 02:08

原帖由 Mazda_6 於 2006-5-29 00:53 發表
請問9X II可唔可以用鋰電

all control can use li-battery but under 12v

作者: mkevin 時間: 2006-5-29 13:15
標題: PCM 9XII
Thank all of you.

作者: mkevin 時間: 2006-5-29 13:42
標題: JR9XII
I changed the throttle position from right hand side to left hand side by replace the Spring.

When I swtich on the control, I notice the sound of BEEZE and the SW Warning in the display.

I donit know what happened.

Please advise me what to do. I have the Chinese menu (Taiwan Version) and English Menu (XP9303
Version) But I cannot find how to change the mode. I insist to have the throttle at left hand side as I sometimes go to California, USA. My control is a new one.

Best regards,

作者: 小步 時間: 2006-5-29 14:34
Beep Warning : Move all switchs up and Thuttle stick down 1st,this ia default warning .
Beware your helichoper or plane will full thuttle when you start the engine or start the motor.

after you replace the spring ,the thuttle stick will goto middle and your turn on the TX must be got warning .

move the thuttle stick at the lowest positon will be ok .
How to goto stick mode setting :
1:Move the thuttle stick on the lowest position and the switchs all flap up side.
2.PRESS the enter key and turn on the TX same time
3.turn the wheel and your will find the [STICK MODE or / STICK DIRECTION] on the MENU
4.Go in you will see 1,2,3,4 CH position setting .You just select mode 1 / mode 2 is ok .

作者: mkevin 時間: 2006-5-30 21:20
標題: JR PCM 9XII
Thank you very much. I can set the mode 2 now.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)