RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 我都加入了DB01行列 [打印本頁]

作者: t2 時間: 2009-3-11 19:45
標題: 我都加入了DB01行列
各位師兄, 多多指教!

[ 本帖最後由 t2 於 2009-3-14 21:02 編輯 ]

作者: t2 時間: 2009-3-11 19:47
想請教各位, 有D咩parts要買定(有d咩易爛)? 因為我係4wd buggy新手.

作者: matlc1234 時間: 2009-3-11 19:56
D arms易爛!!

作者: t2 時間: 2009-3-11 19:59

原帖由 matlc1234 於 2009-3-11 19:56 發表

 登錄/註冊後可看大圖

D arms易爛!!

多謝師兄! 請問用TRF 501x既arm 會好d 嗎?

作者: Evo5 時間: 2009-3-11 20:28

原帖由 t2 於 2009-3-11 07:59 PM 發表

 登錄/註冊後可看大圖

多謝師兄! 請問用TRF 501x既arm 會好d 嗎?

sure la !
nice paint job , done by yourself ??

作者: t2 時間: 2009-3-11 20:33

原帖由 Evo5 於 2009-3-11 20:28 發表

 登錄/註冊後可看大圖

sure la !
nice paint job , done by yourself ??

Thanks. 係呀, 自己噴既. 風翼仍在上色中.

作者: Eddie168 時間: 2009-3-11 21:53

原帖由 t2 於 2009-3-11 19:47 發表

 登錄/註冊後可看大圖

想請教各位, 有D咩parts要買定(有d咩易爛)? 因為我係4wd buggy新手.

Hi c hing nice car, keep an eye on your rear diff, it can break very easily

作者: Marco明 時間: 2009-3-11 21:59
個殼噴得好靚

正

作者: t2 時間: 2009-3-11 22:00

原帖由 Eddie168 於 2009-3-11 21:53 發表

 登錄/註冊後可看大圖

Hi c hing nice car, keep an eye on your rear diff, it can break very easily

吓, 咁請問有咩放法令佢耐用d呀? 部車要整rear diff都要鬆好多鏍絲喎!

作者: t2 時間: 2009-3-11 22:05

原帖由 Marco明 於 2009-3-11 21:59 發表

 登錄/註冊後可看大圖

個殼噴得好靚正

多謝.

其實噴Buggy殼我都係第二次, 希望下次再噴好d.

作者: Eddie168 時間: 2009-3-12 01:45

原帖由 t2 於 2009-3-11 22:00 發表

 登錄/註冊後可看大圖

吓, 咁請問有咩放法令佢耐用d呀? 部車要整rear diff都要鬆好多鏍絲喎!

Make sure the diff is not too tight and is not slipping otherwise the glue between the diff plate and the plastic plate holder will split and will slip against each other (this is fine if you're running a mild motor but im not sure what motor you're running in the picture) and therefore the plate will generate heat and melt the pulley, i would reccomend replace the orginal ones by a TRF501x diff halves as they are straight swap and bullet proof

Here is my way to build my diff and i have never had any problems with my diff before so you might want to have a look at this http://bbs.rc-evo.com/viewthread ... &extra=page%3D2 (This is just my opinion and cannot 100% guarantee it will work everytime) hope this helps

作者: t2 時間: 2009-3-12 06:46

原帖由 Eddie168 於 2009-3-12 01:45 發表

 登錄/註冊後可看大圖

Make sure the diff is not too tight and is not slipping otherwise the glue between the diff plate and the plastic plate holder will split and will slip against each other (this is fine if you're r ...

Thanks a lot.

I'll buy the 501x diff joints shortly and use them to rebuild the diff.

作者: Eddie168 時間: 2009-3-12 08:57

原帖由 t2 於 2009-3-12 06:46 發表

 登錄/註冊後可看大圖

Thanks a lot.

I'll buy the 501x diff joints shortly and use them to rebuild the diff.

Also the Suspension blocks (part A12) and the suspension ball (part A2) are weak points of the car and it's a good idea to replace them with metal ones as they tend to break quite easily if you crash as much as me

but it is not necessary

by the way very nice shell and where do you play??

作者: mlee 時間: 2009-3-12 12:17
Other than A arms, there is also stock support for front and rear. (backup parts incase of Cup 4) Really nice paint job.

作者: t2 時間: 2009-3-12 12:42

原帖由 Eddie168 於 2009-3-12 08:57 發表

 登錄/註冊後可看大圖

Also the Suspension blocks (part A12) and the suspension ball (part A2) are weak points of the car and it's a good idea to replace them with metal ones as they tend to break quite easily if you cr ...

Thanks for your advice. I've changed the suspension ball to metal one but the blocks are still the stock items come with the car. Need to spend money again!

Most likely I'll play it at TRC later (after getting the necessary parts of course).

作者: t2 時間: 2009-3-12 12:45

原帖由 mlee 於 2009-3-12 12:17 發表

 登錄/註冊後可看大圖

Other than A arms, there is also stock support for front and rear. (backup parts incase of Cup 4) Really nice paint job.

Are u talking about the shock tower (M parts)? I've changed them to carbon reinforced ones, hopefully to be stronger (I guess).

作者: mlee 時間: 2009-3-12 15:30
When the car (Cup 4), the car tends to "rub ginger" against the floor so it does not matter if it is carbon re-inforced or carbon fibered, the end result will be the same. Just to be good to have this spare part.

作者: t2 時間: 2009-3-12 18:00

原帖由 mlee 於 2009-3-12 15:30 發表

 登錄/註冊後可看大圖

When the car (Cup 4), the car tends to "rub ginger" against the floor so it does not matter if it is carbon re-inforced or carbon fibered, the end result will be the same. Just to be good to have thi ...

Thanks 師兄.

風翼上色都完成啦.

作者: Marco明 時間: 2009-3-12 18:06
DB-01 MS 花

作者: t2 時間: 2009-3-12 18:09

原帖由 Marco明 於 2009-3-12 18:06 發表

 登錄/註冊後可看大圖

DB-01 MS 花

希望星星真係會出架DB01 MS就正啦!

作者: Marco明 時間: 2009-3-12 18:18

原帖由 t2 於 2009-3-12 18:09 發表

 登錄/註冊後可看大圖

希望星星真係會出架DB01 MS就正啦!

同我架好襯....一齊玩就正

http://bbs.rc-evo.com/viewthread ... ight=%2BMarco%A9%FA

作者: t2 時間: 2009-3-12 18:24

原帖由 Marco明 於 2009-3-12 18:18 發表

 登錄/註冊後可看大圖

同我架好襯....一齊玩就正
http://bbs.rc-evo.com/viewthread ... ight=%2BMarco%A9%FA

好呀! 請問師兄喎邊道玩車車呀?

作者: Marco明 時間: 2009-3-12 18:57

原帖由 t2 於 2009-3-12 18:24 發表

 登錄/註冊後可看大圖

好呀! 請問師兄喎邊道玩車車呀?

我部車落過地一次咋.....黎緊計劃會去TKO玩~~~

作者: t2 時間: 2009-3-12 19:41

原帖由 Marco明 於 2009-3-12 18:57 發表

 登錄/註冊後可看大圖

我部車落過地一次咋.....黎緊計劃會去TKO玩~~~

我應該會去TRC, 因為TRC搬左之後都未有時間試過去佢既buggy場玩.

作者: Eddie168 時間: 2009-3-12 21:49

原帖由 t2 於 2009-3-12 12:45 發表

 登錄/註冊後可看大圖

Are u talking about the shock tower (M parts)? I've changed them to carbon reinforced ones, hopefully to be stronger (I guess).

I personally prefere using the orginal tower because carbon reinforce ones are strong but they are brittle (they can't flex as much as the orginal ones) so if they hit something they tend to snap straight away but the orginal ones flex so can absorb some of the force

作者: t2 時間: 2009-3-12 22:01

原帖由 Eddie168 於 2009-3-12 21:49 發表

 登錄/註冊後可看大圖

I personally prefere using the orginal tower because carbon reinforce ones are strong but they are brittle (they can't flex as much as the orginal ones) so if they hit something they tend to snap ...

Let me do a crash test and see which one is stronger!

作者: mlee 時間: 2009-3-13 14:34

原帖由 Eddie168 於 2009-3-12 21:49 發表

 登錄/註冊後可看大圖

I personally prefere using the orginal tower because carbon reinforce ones are strong but they are brittle (they can't flex as much as the orginal ones) so if they hit something they tend to snap ...

Totally agreed with this C-Hing.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)