RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 蕉插點焊? [打印本頁]

作者: move7648 時間: 2009-4-21 22:50
標題: 蕉插點焊?
請問係加錫响電線, 再塞落蕉插度,
定係熔d錫落蕉插度, 再塞電線落去??

以上兩個方法我都玩唔掂...
我用80~200w辣雞 (槍型o個隻)

作者: kinman182004 時間: 2009-4-21 23:07
我都想知，因為一焊熱力從电線流走，成日唔夠熱，焊極都焊唔到，焊到都成半粒鐘！
咩牌紙同w數嘅辣雞好用？通常枝辣雞要用完要點保養？我用都用咗2枝，一係唔黐錫，一係唔夠熱！

作者: move7648 時間: 2009-4-21 23:23

我都想知，因為一焊熱力從电線流走，成日唔夠熱，焊極都焊唔到，焊到都成半粒鐘！
咩牌紙同w數嘅辣雞好用？通常枝辣雞要用完要點保養？我用都用咗2枝，一係唔黐錫，一係唔夠熱！
kinman182004 發表於 2009-4-21 11:07 PM

登錄/註冊後可看大圖

"唔上錫"問題
你有無落松香?
又可能支雞污槽喎

都係等ching答
我都攪唔掂

作者: f-16 時間: 2009-4-21 23:24
係囉、我焊T插果時又係5痴錫=

作者: 衫魚仔 時間: 2009-4-21 23:24
加錫响電線,熔d錫落蕉插度, 再塞電線落去

作者: samitoneau 時間: 2009-4-21 23:47
for T plug, you have to scratch the soldering surface first in order to the solder stick to it

for banana plug, I melt some solder into the plug first. than use the soldering iron to touch the outside of the banana plug so to heat the solder inside together with the banana plug. since there are a lot of thing being heated, the heat capacity is large and the temperature is kept high for a longer time. When your soldering iron is touching the banana plug and you see the solder inside is melted, put in the wire. After the wire is in place, remove the soldering iron and wait for the solder to cool (I use mouth to blow so to make it cool quicker). after the solder cools down, the wire must be tightly soldered.

better to use a higher watt soldering iron because you have to heat up a lot of things.

This method is easy to success but uses more solder. It might not be the most beautiful soldering method but it is easy to success.

作者: samitoneau 時間: 2009-4-21 23:50
note: don move when the wire is inside the banana plug before the solder cools down.

作者: gordonf35 時間: 2009-4-21 23:55

for T plug, you have to scratch the soldering surface first in order to the solder stick to it

for banana plug, I melt some solder into the plug first. than use the soldering iron to touch the outs ...
samitoneau 發表於 2009-4-21 23:47

登錄/註冊後可看大圖

講左我地既心得出黎，哈哈！

to樓主：依個方法好好用嫁！真係值得一試

作者: kinman182004 時間: 2009-4-22 09:32
6# samitoneau

Thank C-hing...i will try again but can you advise how many Watts of soldering iron will use?

作者: chestertai 時間: 2009-4-22 10:01
Searched from youtube, hope this help

http://www.youtube.com/watch?v=DhrE0FZ9-lo
http://www.youtube.com/watch?v=n9rjxCy2YxU
http://www.youtube.com/watch?v=AzfTY247HSE

作者: kinman182004 時間: 2009-4-22 10:23
10# chestertai

Excellent.....it's very useful link for me. Thank you very much.

作者: move7648 時間: 2009-4-22 11:51
唔該晒咁多位ching, 今晚再試下先

作者: joanne 時間: 2009-4-22 13:33
燒一個半個就 O.K. 我覺得好覆雜又耐. 買含松香的 goots 錫線好好多, 又快. 一焊就溶又唔駛落膏, 又夠實. 我半個鐘可以燒好幾排電, 幾隻摩打. 不過一筒 goots 錫線唔多, 好以 3M 左右. 我又再買咗 2筒 ~!

作者: smalljohndoe 時間: 2009-4-22 15:29
其實旱蕉插係最易, 只要你有支粗既烙鐵咁就ok, 我用開一字批形的
係線同蕉插有個小洞位落錫, 塞電線入去, 再放烙鐵係個小洞頭頂打圈, 烙鐵攞開, 電線定一陣就ok

作者: redbullbull 時間: 2009-4-22 23:30

其實旱蕉插係最易, 只要你有支粗既烙鐵咁就ok, 我用開一字批形的
係線同蕉插有個小洞位落錫, 塞電線入去, 再放烙鐵係個小洞頭頂打圈, 烙鐵攞開, 電線定一陣就ok
smalljohndoe 發表於 2009-4-22 15:29

登錄/註冊後可看大圖

我自己一日旱N咁多對蕉插
因為蕉插佢鍍左金.........多數難上錫
可以先用粗砂紙先打花個蕉插
咁好易上錫架la
仲有隻雞多數用100w-120w
係鴨x街昌x電業到有賣$大約38-60

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)