RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 你地 d 12仔motor 係how many turn? [打印本頁]

作者: silvavisil 時間: 2009-5-5 09:47
標題: 你地 d 12仔motor 係how many turn?
如題

作者: hardmankam 時間: 2009-5-5 10:05
i am new hand... use 2xA123 @6.6V & 好盈 9T
rollout about ~ 35mm

作者: EDI 時間: 2009-5-5 10:44
XRAY 7.5T

作者: raman9551 時間: 2009-5-5 11:04
CRC / 12R5 - 6.5T

作者: tekin 時間: 2009-5-5 11:24
4 cell-4.5R
6 cell-8.5R

作者: pro4 時間: 2009-5-5 12:49
12R5 5.5R A123 2S1P

作者: cowboy 時間: 2009-5-5 16:54
10.5R

作者: silvavisil 時間: 2009-5-5 19:34
HB 12x
8.5T / 5.5T
5200mah Lipo
Motor T=23
Spur Gear=100

作者: hardmankam 時間: 2009-5-5 23:11

HB 12x
8.5T / 5.5T
5200mah Lipo
Motor T=23
Spur Gear=100
silvavisil 發表於 2009-5-5 19:34

登錄/註冊後可看大圖

silvavisil:
Do you run 3.7V or 7.4V Lipo? How do you put the batteries in your 12x. I also have a 12x. Can you post a photo of your car, thanks!

作者: pmkpang 時間: 2009-5-6 00:41
S120 - 8.5T

作者: silvavisil 時間: 2009-5-6 03:28
10# hardmankam

I'm using a 7.4V 分體式 Lipo. Well, if you wanna buy there is only 4200mah left in KWS or 6000mah. but 6000mah is 4-5mm thicker then 4200mah!

作者: ringolau 時間: 2009-5-6 09:03
RC 12L4, EP 4600 4 cells.
好盈60A, Orion 4.5T

作者: hardmankam 時間: 2009-5-6 10:20

10# hardmankam

I'm using a 7.4V 分體式 Lipo. Well, if you wanna buy there is only 4200mah left in KWS or 6000mah. but 6000mah is 4-5mm thicker then 4200mah!
silvavisil 發表於 2009-5-6 03:28

登錄/註冊後可看大圖

silvavisil: which esc r you using? there is not much room for esc + receiver using 分體式 Lipo. here is my setup: http://bbs.rc-evo.com/viewthread ... p;page=1#pid1200958

作者: silvavisil 時間: 2009-5-6 13:55
14# hardmankam

作者: minimini 時間: 2009-5-6 14:03

14# hardmankam
silvavisil 發表於 2009-5-6 13:55

登錄/註冊後可看大圖

呢........呢..........呢..........呢部係咪傳說中........"會飛嘅拖頭"...........

作者: silvavisil 時間: 2009-5-6 14:28
係呀! 1:12 scale. 今日有time DIY again!

作者: hardmankam 時間: 2009-5-6 23:29
15# silvavisil

thanks for share!

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)