RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 轉向 Problems.... [打印本頁]

作者: raymen 時間: 2009-5-10 00:45
標題: 轉向 Problems....
本帖最後由 raymen 於 2009-5-11 23:23 編輯

升起部車轉向時車輪不断震動? But if I take off the wheels is no problems.........

Thks for comments...

作者: WTW 時間: 2009-5-10 00:57
可能接收受到干擾！

作者: 丘比凸 時間: 2009-5-10 00:57
虛位作怪

作者: raymen 時間: 2009-5-10 01:55
How to solve it ?

作者: 丘比凸 時間: 2009-5-10 02:06

How to solve it ?
raymen 發表於 2009-5-10 01:55

登錄/註冊後可看大圖

我攝下塞下整實淨佢

作者: raymen 時間: 2009-5-10 02:25

我攝下塞下整實淨佢
丘比凸發表於 2009-5-10 02:06 AM

登錄/註冊後可看大圖

U mean the C-hub ?

作者: raymen 時間: 2009-5-11 01:04
Any more suggestions ??

Is that normal to the 1/10 tourings ?

作者: WallaceNg 時間: 2009-5-11 01:24
係咪一開著部車，個servo就係到震啊？
係既你試下開左支控，移下d電線睇下有冇好轉
我之前係咁，支後發覺控入面d電線放係一d位係會有干擾

作者: raymen 時間: 2009-5-11 15:17
No....

升起部車轉向時車輪不断震動 FULL hand

作者: cowboy 時間: 2009-5-11 15:34
有冇set downstops？

作者: raymen 時間: 2009-5-11 16:24
What is downstops ?

How to do it, thks for your help......

作者: Marco明 時間: 2009-5-11 16:32
應該係成份轉向組件既虛位所造成........

作者: raymen 時間: 2009-5-11 16:35
本帖最後由 raymen 於 2009-5-11 23:28 編輯

應該係成份轉向組件既虛位所造成........
Marco明發表於 2009-5-11 04:32 PM

登錄/註冊後可看大圖

作者: cowboy 時間: 2009-5-14 11:38
係咪用手攞起部車、俾油、轉向、跟住車輪不断震動?

作者: hoitang55 時間: 2009-5-14 12:12
如比油轉向震,虛位問題,用介子攝攝佢
如冇比油都震,servo有干擾

作者: lung1 時間: 2009-5-14 12:37
"升起部車轉向時車輪不断震動" it is normal...........

作者: cowboy 時間: 2009-5-14 13:11
樓主講多少少啦！當時有冇俾油？有冇相睇？

作者: tekin 時間: 2009-5-14 13:15
servo problem, change other servo to test.

作者: cowboy 時間: 2009-5-14 13:26

servo problem, change other servo to test.
tekin 發表於 2009-5-14 13:15

登錄/註冊後可看大圖

Basing on the limited information:

升起部車轉向時車輪不断震動? But if I take off the wheels is no problems.........

It seems that it may not be a servo problem........wheels shake when they were put on while no shake was found when they were put off.....

作者: lung1 時間: 2009-5-14 13:40
本帖最後由 lung1 於 2009-5-14 13:42 編輯

don't worry, most of the car have this problem...
(assume that your car suspension, servo condition is no problem)

the solution is to change this one, but only suitable for xray and HB CYCLONE..

For XRAY:

登錄/註冊後可看大圖

For cyclone:

登錄/註冊後可看大圖

作者: nobuster 時間: 2009-5-14 15:06
你用乜控乜接收先

作者: raymen 時間: 2009-5-14 17:02

don't worry, most of the car have this problem...
(assume that your car suspension, servo condition is no problem)

the solution is to change this one, but only suitable for xray and HB CYCLONE..
...
lung1 發表於 2009-5-14 01:40 PM

登錄/註冊後可看大圖

Yes... thanks this is my problems!

Thanks all brothers.... x 100000000000

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)