RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Xray 009 Gear Ratio 齒比 [打印本頁]

作者: gavl 時間: 2009-6-3 19:02
標題: Xray 009 Gear Ratio 齒比
search 過舊文，好多人都問過xray 009 gear ratio，set up book 有chart 提過同都睇過，個chart 提到最細 recommand既 48Pitch 係80 tooth，64 pitch 係110 pitch，唔知大家用到 / 用緊最細 / 最大既spur gear 係幾多，同大家用緊原裝齒定speed mind?

作者: defcone 時間: 2009-6-3 19:44
Gear ratio depends on your motor and the track you are running on.

作者: rcytong 時間: 2009-6-3 21:49
我用過原裝及Speedmind. 原裝比較快損耗,但Speedmind比較責.

作者: lung1 時間: 2009-6-3 22:17

search 過舊文，好多人都問過xray 009 gear ratio，set up book 有chart 提過同都睇過，個chart 提到最細 recommand既 48Pitch 係80 tooth，64 pitch 係110 pitch，唔知大家用到 / 用緊最細 / 最大既spur gear 係幾多 ...
gavl 發表於 3/6/2009 19:02

登錄/註冊後可看大圖

大減牙64PITCH 最細可以用104
48PITCH 最細可以用78

作者: Chrispo 時間: 2009-6-3 22:31

search 過舊文，好多人都問過xray 009 gear ratio，set up book 有chart 提過同都睇過，個chart 提到最細 recommand既 48Pitch 係80 tooth，64 pitch 係110 pitch，唔知大家用到 / 用緊最細 / 最大既spur gear 係幾多 ...
gavl 發表於 2009-6-3 19:02

登錄/註冊後可看大圖

From XRAY forum, one of the team drivers has stated the formula for chosing the range of the spur-pinon gears. It's (48 pitch) from 101 to 112. That means the sum of spur gear + pinion gear should be within 101 to 112. I'm running 8.5T with the final gear ratio of 5.10. My spur gear is 78 while the pinion is 27. The sum of spur and pinion = 78 + 27 = 105 which is within 101 - 112.

I hope the formula is helpful for you to work out the combinations of spur and pinon gears for your desired final gear ratio. Hope is helpful.

作者: cowboy 時間: 2009-6-3 23:24

From XRAY forum, one of the team drivers has stated the formula for chosing the range of the spur-pinon gears. It's (48 pitch) from 101 to 112. That means the sum of spur gear + pinion gear should b ...
Chrispo 發表於 2009-6-3 22:31

登錄/註冊後可看大圖

Wow! 8.5T with 5.1! Isn't it too aggressive? Which track you run?

作者: Chrispo 時間: 2009-6-4 00:05
There is a mistake! I mixed up with the no. of "T". Better to say I'm running 4000kv with 4.91 - 5.10 as FDR. I think it makes sense better in this way. I did run LRP x11 Stock Spec 8.5T (4700kv) with 5.44 - 5.67 as FDR.

作者: gavl 時間: 2009-6-4 00:27

Gear ratio depends on your motor and the track you are running on.
defcone 發表於 2009-6-3 19:44

登錄/註冊後可看大圖

Fully understand the gear ratio it depands on track size / driving style or some un-certain factor, so i'm not asking something no definitely answer.

作者: gavl 時間: 2009-6-4 00:34

我用過原裝及Speedmind. 原裝比較快損耗,但Speedmind比較責.
rcytong 發表於 2009-6-3 21:49

登錄/註冊後可看大圖

我今日試過用speedmind spur gear (已經手磨左塊)，但有一個問題因speedmind齒厚身左原裝個三粒鑼絲唔夠長，用3 x 4mm又長左小小，"修"到過左個adaptor小小頂到隻20T膠牙，變得有小小"kick"住，唔知師兄可唔可以影下你架車個spur gear個度點整？ Thanks!

作者: gavl 時間: 2009-6-4 00:52

From XRAY forum, one of the team drivers has stated the formula for chosing the range of the spur-pinon gears. It's (48 pitch) from 101 to 112. That means the sum of spur gear + pinion gear should b ...
Chrispo 發表於 2009-6-3 22:31

登錄/註冊後可看大圖

Thanks Bro. the formula is helpful, now need to decide the smaller spur gear can use on T2 009 first (i'm running 11.5T), the motor i try arround 5.1 on Pro4, but still slow and not powerful enough (compare with other's running 11.5T on same track)。

作者: lung1 時間: 2009-6-4 07:47

我今日試過用speedmind spur gear (已經手磨左塊)，但有一個問題因speedmind齒厚身左原裝個三粒鑼絲唔夠長，用3 x 4mm又長左小小，"修"到過左個adaptor小小頂到隻20T膠牙，變得有小小"kick"住，唔知師兄可唔可 ...
gavl 發表於 4/6/2009 00:34

登錄/註冊後可看大圖

用平頭SCREW 就可以...

作者: Chrispo 時間: 2009-6-4 09:57

Thanks Bro. the formula is helpful, now need to decide the smaller spur gear can use on T2 009 first (i'm running 11.5T), the motor i try arround 5.1 on Pro4, but still slow and not powerful enoug ...
gavl 發表於 2009-6-4 00:52

登錄/註冊後可看大圖

To answer your question, I've tried usig 76-tooth 48 pitch spur gear on my XRAY. Mine is 008 and it should be very similar to your 009. The fact is if you are already running 5.1 for your 11.5T, have you ever checked the motor temp after running for 5 minutes? I've been using Team Powers 4000kv, running for 8 minutes with the above mentioned FDR (4.p1 - 5.10), the motor temp is about 64 - 68 deg (if I'm extremely hard and rough on my car, I can get up to 70 deg). Hope the info is helpful to you.

I do use SpeedMind and haven't needed to do any modification to the spur gear. I will switch to M3 x 6 flathead screws and left the adaptor not in use. I can post you some photos this evening if you need them.

作者: gavl 時間: 2009-6-4 17:11
本帖最後由 gavl 於 2009-6-4 17:32 編輯

用平頭SCREW 就可以...
lung1 發表於 2009-6-4 07:47

登錄/註冊後可看大圖

我都係用緊hex 圓頭，um..........你講平頭鑼絲，你係咪講緊上底板有斜位("bearbar")個隻？

試左真係ok喎，用卡尺度過D 3x4mm謂圓頭實際條長過4mm，but 平頭係4mm到，but thank you!

作者: gavl 時間: 2009-6-6 02:15

To answer your question, I've tried usig 76-tooth 48 pitch spur gear on my XRAY. Mine is 008 and it should be very similar to your 009. The fact is if you are already running 5.1 for your 11.5T, hav ...
Chrispo 發表於 2009-6-4 09:57

登錄/註冊後可看大圖

Thank you for your details info, i think the info. is helping other's player too.
I didn't check the temp after running (cause i don't have thermometer, and should get 1 very soon), as i said last run my 11.5T with pro4 @5.1, the car has reach the top speed in the middle of forthright, and a little slowing down after, is that strange? but anyway i prepare all i need on my 009 and try to found the best setting with 11.5T on next run..

If u don't mind would u like to take some pics on the speedmind spurgear set? with the flathead screw.

作者: Chrispo 時間: 2009-6-6 08:32

Thank you for your details info, i think the info. is helping other's player too.
I didn't check the temp after running (cause i don't have thermometer, and should get 1 very soon), as i said las ...
gavl 發表於 2009-6-6 02:15

登錄/註冊後可看大圖

Will post the photos this evening, please be patient!

"Slowing down" is a strange description to me!! Do you mean your car is not having much acceleration or is not further picking up speed from the mid of the straight to the first corner down the straight? May I ask where do you run your car most of the time? At TC, TRC or PYC?

作者: Chrispo 時間: 2009-6-6 23:03
13# gavl
Hi Gavl, take a look at these photos and hope they are helpful to you.

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

作者: gavl 時間: 2009-6-8 01:22
Thanks Brp. chrispo, i will take some of mine tomorrow, guess similar to your's but just didn't work on my car.

作者: tekin708 時間: 2009-6-8 07:27
i use xray spur gear because of not expensive($2x) and durable.
the max spur gear size may be 48pitch-87T, 64pitch-118T

作者: tekin708 時間: 2009-6-8 14:49

Thanks Brp. chrispo, i will take some of mine tomorrow, guess similar to your's but just didn't work on my car.
gavl 發表於 2009-6-8 01:22

登錄/註冊後可看大圖

so i use xray spur gear to my 007/008 only because of without modify, quite durable and not expensive.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)