RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 艱苦經歷.......TT01-M(FINISHED #2) [打印本頁]

作者: koji1230 時間: 2009-6-4 02:06
標題: 艱苦經歷.......TT01-M(FINISHED #2)
本帖最後由 koji1230 於 2009-6-7 23:35 編輯

艱苦經歷.......TT01-M

DAY ONE:
original frp chassis is too soft

hand made a 2mm Alum. chassis..........

TO BE CONTINUE

作者: koji1230 時間: 2009-6-4 02:10
本帖最後由 koji1230 於 2009-6-7 19:41 編輯

if i use m03 萬向 @ TT01 - M, do i need to change the 前後杯 to metal parts,or i can use originla 前後杯? thx c hing

DAY 2:
hand made main shaft

build up the chassis

作者: chacha 時間: 2009-6-4 02:16
咁辛苦呀…師兄，如果照抄，買套板好過

作者: koji1230 時間: 2009-6-4 02:21
3# chacha
haha

DIY ma

作者: chacha 時間: 2009-6-4 02:29
用手鋸定積梳

作者: koji1230 時間: 2009-6-4 02:36
5# chacha
積梳,c hing, can u answere me the question in #2??
thx

作者: Tamadi 時間: 2009-6-4 03:08
樓主嘅心幾另人佩服 !

不過比我就, 一係等碳纖板出, 一係就買多塊底板, 一齊裝當加硬 !

作者: Angtr 時間: 2009-6-4 04:10
just an advice! your aluminium sheet will not able to take impact, as those are not heat treated aluminium, will twist and band easily, strongly suggest you use stronger upper deck.

Original TT f/r up rights are ok, if you got spares bucks, good way to buy aluminium f/r up rights.
appreciate your post, I m also using alu sheet for off my buggie under trade protections.

作者: wingwing 時間: 2009-6-4 13:53
精神可嘉！不過鋁板一撞就曲，C hing 要有心理準備。

ps 令我想起我第一架遙控車 - 林宝 Countach LP 500.....
http://oldtamiya.interfree.it/models/58008.htm

作者: tekin 時間: 2009-6-4 14:00
hard work

作者: 清清 時間: 2009-6-4 14:37
不要介意，因我覺得有法國大餐感覺

作者: 大野 時間: 2009-6-4 14:49
嘩...好大功程呀.

作者: smallfaifai 時間: 2009-6-4 15:41

if i use m03 萬向 @ TT01 - M, do i need to change the 前後杯 to metal parts,or i can use originla 前後杯? thx c hing
koji1230 發表於 2009-6-4 02:10

登錄/註冊後可看大圖

要轉金屬parts......建議連差速齒都換埋其他touring的牙差齒，咁就可以用普通o既金屬差速杯連接萬向。

作者: raymen 時間: 2009-6-4 16:32
本帖最後由 raymen 於 2009-6-4 16:38 編輯

This is a very good idea , I do almost for all my cars .....

except Buggy!

作者: koji1230 時間: 2009-6-4 18:10
11# 清清
haha,i'm in holiday,just make some DIY
may be it's no use ga

作者: truckman 時間: 2009-6-4 21:12

This is a very good idea , I do almost for all my cars ..... except Buggy!
raymen 發表於 2009-6-4 16:32

登錄/註冊後可看大圖

還以為C兄改油車，2層板咪好重

作者: chacha 時間: 2009-6-4 21:54
可能師諗住可以散埋熱呢

作者: powis 時間: 2009-6-4 22:11

要轉金屬parts......建議連差速齒都換埋其他touring的牙差齒，咁就可以用普通o既金屬差速杯連接萬向。
smallfaifai 發表於 2009-6-4 15:41

登錄/註冊後可看大圖

then the cost to make the TT01M is very expensive wor!

作者: koji1230 時間: 2009-6-4 22:48
18# powis
agree

i use original 差速齒 ja
i don't want put much $ in this car

not worth!

作者: koji1230 時間: 2009-6-4 22:50

可能師諗住可以散埋熱呢
chacha 發表於 2009-6-4 21:54

登錄/註冊後可看大圖

i think it will "cup" 熱 ......

haha

作者: koji1230 時間: 2009-6-8 00:37
at last,i have run it once @ basketball playground,performance ok,control like M03,
but better than M03 coz of 4WD is better handling,about this car $320.......pass la

作者: Andrew168 時間: 2009-6-10 15:02
DIY 嘅心, 真得一讃

作者: chacha 時間: 2009-6-10 15:13
何解要加多塊 2mm 鋁板呢

作者: koji1230 時間: 2009-6-10 22:48

何解要加多塊 2mm 鋁板呢
chacha 發表於 2009-6-10 15:13

登錄/註冊後可看大圖

i think it would be more safety..........

haha.......may be it's not safe

作者: chacha 時間: 2009-6-10 22:55
24# koji1230

自幼無心向學，英文程度有限

作者: 3BG 時間: 2009-6-11 11:06
just try the tt01M，not bad and very fast

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)