RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Solder iron advice [打印本頁]

作者: yikl 時間: 2009-8-4 00:51
標題: Solder iron advice
Hi C-hing.

I want to replace the wires on my LRP esc. I am using a 80w goot solder iron from Ap Liu Street but it is not easy to take the wires out. Does any c-hing have good recommendations on which solder iron to use to replace wires? I try to find some flat head iron but can't find something nice.

Thanks.

作者: Noir.KAZE 時間: 2009-8-4 00:59
你有冇吸鍚泵?
冇既可以買返支試下
你難take out those wires係佢仲未熱甩唔到定點先
可以買隻w大數d既iron試下(最好買返日本仔野)

作者: EXEX12345 時間: 2009-8-4 01:10

你有冇吸鍚泵?
冇既可以買返支試下
你難take out those wires係佢仲未熱甩唔到定點先
可以買隻w大數d既iron試下(最好買返日本仔野)
Noir.KAZE 發表於 2009-8-4 00:59

登錄/註冊後可看大圖

但佢以經用緊80W LA BOR

作者: Noir.KAZE 時間: 2009-8-4 01:13
應該仲有d大d既
我隻雞雞地都有120W

作者: lung1 時間: 2009-8-4 01:15
其實80W已足夠, 最緊要係支雞要係恆溫, 同埋唔好落太多錫...
太多錫就算100W 都無用.....

作者: lkwmic 時間: 2009-8-4 01:18
用松香會更好！

作者: yikl 時間: 2009-8-4 01:37
Thanks c-hing. I think one of the problem is the solder iron is using those pencil like tips. I think those with a large flat surface is easier to use.

Lung1, what is 恆溫? How can I tell if my solder iron is 恆溫? Thanks.

作者: yikl 時間: 2009-8-4 01:39
2# Noir.KAZE

I put the iron on the spot, but the solder doesn't melt. But I turn on the solder iron for a long time la wor.

作者: 肥神 時間: 2009-8-4 02:17
i think you can suggest this solder iron :http://www.goot.co.jp/c/detail.html
i'm using PX-242,IT IS A VERY GOOD product!! 219$ IN 華輝,鴨記!!

作者: LeoChan 時間: 2009-8-4 02:20

作者: yikl 時間: 2009-8-4 09:28
9# 肥神

Thanks. I will go to 華輝,鴨記 this weekend.

作者: cottonchu 時間: 2009-8-4 23:15
現在不是個個都改為用松香la 咩?

作者: Andrew168 時間: 2009-8-5 11:47
可能有一點冇留意, 就係錫線質素, 要買d好質素錫線

作者: dtm 時間: 2009-8-5 13:30
An 80W Goot iron even with a pointed tip is more than enough to do the job. In fact be careful with it when using next to electronic components, you will have those melting off the board before you know it. I normally use a 60W goot iron for normal work and 100W flat tip for soldering batteries only.

Clean the tip when it is hot with a damn sponge. Melt a little new solder onto the cleaned tip to "tin" it. Then apply on the joint, works every time. If you put a dirty iron to the joint, you will not get anywhere.......

作者: AMAT 時間: 2009-8-5 18:01
WATT數唔係重點

重點係......能否衡溫.
同埋個辣雞咀合唔合適.

宜家果O的電子產品,用尖咀O既唔係好適合,要換成斜CUT平咀果O的,加上衡溫,咁就可以好快咁焊好你想焊O既電變同電線.

個人就用緊呢個白光(HAKKO)加斜平咀,好好用.
一定要買返HAKKO出O既咀.

主要係要支辣雞溫度可以完全去到支雞咀,咁先有用.80WATT絕對足夠.
太熱你仲衰,焊壞O的電子O野.

咩吸錫泵呀,冇乜用.

作者: lkwmic 時間: 2009-8-5 18:55
吸錫泵是當你焊錯了錫的時候用的！

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)