RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 733離合器啤令問題 [打印本頁]

作者: lailcm 時間: 2009-8-31 00:15
標題: 733離合器啤令問題
唔知點解玩唔夠一缸油個離合器壓力啤令就爆開已換過兩次, 跟說明書安裝隙位0.7mm, 及比油唔多去,較鬆D個彈弓好少少,但玩兩玩自己又上返緊, 唔識行,有無師兄可以幫幫忙....

作者: redbullbull 時間: 2009-8-31 00:35
我架車行左2L油都冇出現問題

作者: lailcm 時間: 2009-8-31 01:16
2# redbullbull

你最好check下, 我懷疑佢原裝來的時候22T個齒反轉裝錯比我令17T個齒出左小小頂住個壓力啤令不平所以爆開, 還有check下個油缸彈弓位, 我買返呢就爆左要等兩星期先有貨, 還有check下個離合器黑色個三塊低掌D孔位方向,同說明書所講不同, 唔知會唔會有影響, 頭波箱D牙又有問題 QC問題多多......made in china

作者: redbullbull 時間: 2009-8-31 01:21

2# redbullbull

你最好check下, 我懷疑佢原裝來的時候22T個齒反轉裝錯比我令17T個齒出左小小頂住個壓力啤令不平所以爆開, 還有check下個油缸彈弓位, 我買返呢就爆左要等兩星期先有貨, 還有check下個離合器黑色 ...
lailcm 發表於 2009-8-31 01:16

登錄/註冊後可看大圖

我只有油江問題囉
但我拿3天就換了比我十分快手
換了的新油江就沒有問題了

作者: superx 時間: 2009-8-31 16:59
wa..733 so ma fan ge...

作者: lailcm 時間: 2009-8-31 21:06
唔ma fan 你只要check 清楚先比錢就無問題 la..........主要係油缸睇清楚D, 如果你抽到無爆就恭喜你......

作者: redbullbull 時間: 2009-8-31 21:08

唔ma fan 你只要check 清楚先比錢就無問題 la..........主要係油缸睇清楚D, 如果你抽到無爆就恭喜你......
lailcm 發表於 2009-8-31 21:06

登錄/註冊後可看大圖

最新果批733換晒新油江la
爆油江問題叫做解決了

作者: lailcm 時間: 2009-8-31 21:09

我只有油江問題囉
但我拿3天就換了比我十分快手
換了的新油江就沒有問題了
redbullbull 發表於 2009-8-31 01:21

登錄/註冊後可看大圖

已經係一個月前的事,我估我係早期有問題果D所以要等貨到掛.....

作者: macau-rc 時間: 2009-9-1 09:23
如果抽到無爆油缸就恭喜!? Snake 可以上市啦, 只係賣油缸都發達！

作者: mtaristo 時間: 2009-9-1 09:30

唔知點解玩唔夠一缸油個離合器壓力啤令就爆開已換過兩次, 跟說明書安裝隙位0.7mm, 及比油唔多去,較鬆D個彈弓好少少,但玩兩玩自己又上返緊, 唔識行,有無師兄可以幫幫忙....
lailcm 發表於 2009-8-31 00:15

登錄/註冊後可看大圖

clutch gap 0.7 mm is correct but what's the end play? Should be 0.1 mm. Too large end play will make the thrust bearing damage in very short time. (btw, Do you know what is endplay?)

作者: lailcm 時間: 2009-9-1 21:40

clutch gap 0.7 mm is correct but what's the end play? Should be 0.1 mm. Too large end play will make the thrust bearing damage in very short time. (btw, Do you know what is endplay?)
mtaristo 發表於 2009-9-1 09:30

登錄/註冊後可看大圖

師兄我唔係好明end play是什麼,
你意思係咪clutch gap 越小越好呀

作者: mtaristo 時間: 2009-9-2 12:04
本帖最後由 mtaristo 於 2009-9-2 12:07 編輯

師兄我唔係好明end play是什麼,
你意思係咪clutch gap 越小越好呀
lailcm 發表於 2009-9-1 21:40

登錄/註冊後可看大圖

spare sometime and try to understand the instruction manual.

  you must understand what is clutch gap and what is end paly first.

btw the way, clutch gap is the gap between the clutch shoe and clutch bell before engage. In your case, 0.7 mm is almostly correct.  Endplay is the amount of the movement of the clutch bell along the engine shaft after you installed the whole clutch set to the engine. Normally the endplay should be 0.1 mm, too large endplay will damage the thrust bearing.

how to make clutch gap 0.7 mm and endplay 0.1 mm, the 733 instruction manual, XRAY NT1 manaul, Teammagic G4 manaul, Mugen MTX-4 manual tells you very clearly. Please put sometime to read the manaul and try to understand it.

It is very important to a GP player

作者: mtaristo 時間: 2009-9-2 15:45
本帖最後由 mtaristo 於 2009-9-2 16:01 編輯

(from XRAY NT1 instruction manual)

setting cltuch gap first,
[attach]297341[/attach]

then set the endplay
[attach]297339[/attach]

[attach]297342[/attach]

作者: lailcm 時間: 2009-9-2 20:43
哦!!明白唔該晒師兄..............

作者: mtaristo 時間: 2009-9-2 21:34

哦!!明白唔該晒師兄..............
lailcm 發表於 2009-9-2 20:43

登錄/註冊後可看大圖

welcome and enjoy GP.

作者: turky 時間: 2009-10-5 19:16
我都試過齒杯令斷，d質數真係，，，
我舊果d用2年都末斷過

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)