RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: F103 用12仔 SERVO ? [打印本頁]

作者: lung1 時間: 2009-11-18 10:15
標題: F103 用12仔 SERVO ?
有無CHING 係F1上裝12仔 SERVO 呢?
我睇返個SPEC 隻9650 都唔差BOR~

PHOTO FROM RC-EVO:

作者: yokomo 時間: 2009-11-18 10:28
I am now using Sanwa 141 in my F103GT, handling is quite good.

作者: lung1 時間: 2009-11-18 11:06

I am now using Sanwa 141 in my F103GT, handling is quite good.
yokomo 發表於 18/11/2009 10:28

登錄/註冊後可看大圖

師兄有無相睇下??

作者: hardmankam 時間: 2009-11-18 11:11
本帖最後由 hardmankam 於 2009-11-18 11:13 編輯

I am using Futaba 9650 on F103 (F1). I can post a pic tonight.
btw, S9650 is digital and plastic gears. (not analog and metal gear)

作者: yokomo 時間: 2009-11-18 11:18
OK, I will take some pics for your reference.

作者: lung1 時間: 2009-11-18 11:18

I am using Futaba 9650 on F103 (F1). I can post a pic tonight.
btw, S9650 is digital and plastic gears. (not analog and metal gear)
hardmankam 發表於 18/11/2009 11:11

登錄/註冊後可看大圖

THANKS~
請問CHING 係點裝...??

作者: hardmankam 時間: 2009-11-18 11:25
I mount the servo with the servo saver facing upwards, with this way, I do not have to cut the ears off. But I have to cut the F103 servo mount a little for this to work. I will post a picture for you to see tonight.

作者: cHRisTiAN 時間: 2009-11-18 11:33

THANKS~
請問CHING 係點裝...??
lung1 發表於 2009-11-18 11:18

登錄/註冊後可看大圖

buy Tamiya (#51380) F104 D Parts (Battery Holder).
which include two servo mount, one for standard size servo, next one for 12son servo size.
also you can install 104servo mount on your 103, that is OK.

作者: lung1 時間: 2009-11-18 11:49

I mount the servo with the servo saver facing upwards, with this way, I do not have to cut the ears off. But I have to cut the F103 servo mount a little for this to work. I will post a picture for ...
hardmankam 發表於 18/11/2009 11:25

登錄/註冊後可看大圖

THANKS~等你POST 相~

作者: lung1 時間: 2009-11-18 11:50

buy Tamiya (#51380) F104 D Parts (Battery Holder).
which include two servo mount, one for standard size servo, next one for 12son servo size.
also you can install 104servo mount on your 103, that ...
cHRisTiAN 發表於 18/11/2009 11:33

登錄/註冊後可看大圖

lomay 同我講左啦~

不過我諗住將隻servo 訓底放~

作者: hardmankam 時間: 2009-11-18 12:12
one problem i found by servo 訓底放 is that the steering link cannot be parallel with the a-arms. (the servo saver ball connector is a lot higher than the steering block ball connector).

作者: cHRisTiAN 時間: 2009-11-18 12:13
10# lung1
i see~~~
also i thing you may need to cut your shell .

作者: hardmankam 時間: 2009-11-18 22:06
here are some photos

作者: hardmankam 時間: 2009-11-18 22:07
sorry, here are the rest of the photos

作者: tomatchinhk 時間: 2009-11-19 00:42
我用 ko metal gear... 吾記得什麼型號

http://www.flickr.com/photos/24652306@N07/3953043067/

作者: lung1 時間: 2009-11-20 13:59
唔該曬襟多位~!

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)