RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: MR03 AE86改改改 [打印本頁]

作者: billy86che 時間: 2010-1-2 21:07
標題: MR03 AE86改改改
some photos[attach]333324[/attach]

作者: SuperAguri 時間: 2010-1-2 22:19
孖彈弓代替 cha cha 玩成點 ?

作者: billy86che 時間: 2010-1-2 22:23
本帖最後由 billy86che 於 2010-1-2 22:52 編輯

應該唔會再用cha cha.
Here are some ways to tune the rear suspension. And I can keep the plastic T plates.

作者: LokSpec 時間: 2010-1-2 23:27
媽星四驅車8T紫齒?

作者: tscc 時間: 2010-1-2 23:30
1# billy86che

快d申請設計專利, 如果唔係就益晒d"傷人"

作者: billy86che 時間: 2010-1-2 23:35
本帖最後由 billy86che 於 2010-1-2 23:36 編輯

4# LokSpec

Yes, very cheap.

But very quiet.

作者: LokSpec 時間: 2010-1-2 23:51
本帖最後由 LokSpec 於 2010-1-2 23:55 編輯

4# LokSpec

Yes, very cheap. But very quiet.
billy86che 發表於 2010-1-2 23:35

登錄/註冊後可看大圖

好消息

因剛收了朋友的MR02

一物兩用

睇真D,條RS-Watanabe 闊尾軨係DIY的嗎?

作者: billy86che 時間: 2010-1-2 23:53
7# LokSpec

Did you mean the 8T gear?

作者: LokSpec 時間: 2010-1-2 23:58

7# LokSpec

Did you mean the 8T gear?
billy86che 發表於 2010-1-2 23:53

登錄/註冊後可看大圖

Yes,
That mean TAMIYA 1/32 Mini 4WD and MR Series Mini-Z can use the same 8T gear

作者: billy86che 時間: 2010-1-3 00:01
9# LokSpec

4x plastic purple 8T + 4X metal 8T = 200 yen only

作者: LokSpec 時間: 2010-1-3 00:09

9# LokSpec

4x plastic purple 8T + 4X metal 8T = 200 yen only
billy86che 發表於 2010-1-3 00:01

登錄/註冊後可看大圖

Is plastic purple 8T better than the metal 8T?

BTW, 8 pcs plastic purple 8T only 157 yen only

http://www.tamiya.com/japan/prod ... wd_ao/kitA70001.htm

登錄/註冊後可看大圖

AO-1014

作者: billy86che 時間: 2010-1-3 00:12

Is plastic purple 8T better than the metal 8T?

BTW, 8 pcs plastic purple 8T only 157 yen only

http://www.tamiya.com/japan/prod ... wd_ao/kitA70001.htm
http://www.tamiya.com/jap ...
LokSpec 發表於 2010-1-3 00:09

登錄/註冊後可看大圖

The only use of the metal gears is to be thrown directly to the bin. You can test your basketball skills.

作者: d.s 時間: 2010-1-3 01:12
鬼斧神工!!勁!!

作者: 800mah 時間: 2010-1-3 02:36
i like your ball diff very much, can u tell me how did u shift spur gear inwards ?

作者: sky88602828 時間: 2010-1-3 05:56
1# billy86che
老師,你真係好利害!而且咁多年都係鐘意AE86! CT Raymond

作者: paulpoon306 時間: 2010-1-3 12:29
老師,你起边個場玩開?等我跟你學吓嘢先..! CT or MMS?

作者: ellis 時間: 2010-1-3 18:18
何解車底仲用膠t-板

作者: billy86che 時間: 2010-1-3 21:10

i like your ball diff very much, can u tell me how did u shift spur gear inwards ?
800mah 發表於 2010-1-3 02:36

登錄/註冊後可看大圖

The gear is DIY. I put 2 gears together and remove all the teeth of the outer one, so there is room for a wider tyre.

作者: billy86che 時間: 2010-1-3 21:14
本帖最後由 billy86che 於 2010-1-3 21:47 編輯

老師,你起边個場玩開?等我跟你學吓嘢先..! CT or MMS?
paulpoon306 發表於 2010-1-3 12:29

登錄/註冊後可看大圖

I play this on Wednesday at CT. I am using a 60-turn motor and run for more than 35 mins each pack of battery. Most people playing that night are using slow motors and can run for at least 20 mins. Interested?

作者: billy86che 時間: 2010-1-3 21:17
本帖最後由 billy86che 於 2010-1-3 21:22 編輯

17# ellis

"何解車底仲用膠t-板 "

That is exactly the reason why I am using 2 shocks, not a defect.

Still don't understand?

膠t-板先至正!

作者: billy86che 時間: 2010-1-3 21:58
本帖最後由 billy86che 於 2010-1-3 22:01 編輯

i like your ball diff very much, can u tell me how did u shift spur gear inwards ?
800mah 發表於 2010-1-3 02:36

登錄/註冊後可看大圖

See this higher resolution pic. Click to enlarge.

作者: 800mah 時間: 2010-1-3 23:11

See this higher resolution pic. Click to enlarge.
billy86che 發表於 2010-1-3 21:58

登錄/註冊後可看大圖

thank you very much, so AA glue will do the bonding between the two gears?

作者: billy86che 時間: 2010-1-4 14:34

thank you very much, so AA glue will do the bonding between the two gears?
800mah 發表於 2010-1-3 23:11

登錄/註冊後可看大圖

Yes. But you'd better file the surface a little bit and apply pressure when you glue it.

作者: 2slow 時間: 2010-1-4 14:55
billy86che師兄既作品往往都有驚喜... good job...
any detail report compares to conventional 尾擔?

作者: CIVICMAN 時間: 2010-1-4 15:23
勁勁勁勁勁勁吖

作者: billy86che 時間: 2010-1-4 15:38
Can't say it's detail but that's what I 've found:
1. The car ran so well the first time that I have given up playing with my modified MR02 AE86 from then on, which I had been playing with for more than 3 years.
2. I don't have to worry about changing the T plates to adjust the car's characteristics in centering force after rolling or when it breaks or gets worn out. (Plastic T plates are durable.)
3. I believe the oil damper shocks (with oil & pistons inside), which absorb vibration in a more linear way, give the rear a better grip than the conventional friction damper plates.

作者: chacha 時間: 2010-1-8 12:51

應該唔會再用cha cha.
Here are some ways to tune the rear suspension. And I can keep the plastic T plates.
billy86che 發表於 2/1/2010 22:23

登錄/註冊後可看大圖

應該申請設計專利左右平衡阻尼器 (如3件左中右彈弓)
圖片摩托車自行車 Damper

作者: billy86che 時間: 2010-1-11 05:03

應該申請設計專利左右平衡阻尼器 (如3件左中右彈弓)
圖片摩托車自行車 Damper
chacha 發表於 2010-1-8 12:51

登錄/註冊後可看大圖

That's for steering, not for suspension. They are similar in shape but not in its purpose.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)