RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 唔知點解我隻Novak 4.5R摩打run完熱到辣手既? [打印本頁]

作者: jasonwong 時間: 2006-7-11 12:10
標題: 唔知點解我隻Novak 4.5R摩打run完熱到辣手既?
隻Novak 4.5R係新買既連GTB........

run完(無駁摩打齒空轉)熱到辣手既, 同埋行到某轉數個摩打就有d震+有唔唔聲(好似有d野頂住左咁)

Anyone can help me...??

[ 本帖最後由 jasonwong 於 2006-7-11 12:16 編輯 ]

作者: peter7 時間: 2006-7-11 13:05
check pm

作者: lceriyirri 時間: 2006-7-11 13:27
Oh.. I want to know too.
lemme see your pm too :p

I am planning to get a brushless too, so it sure will help

作者: jasonwong 時間: 2006-7-11 13:29
(FROM peter7) don't ever let the motor 空轉 too long because the rpm is too high. Try it on the car. If this is no overheat, your system is ok.

作者: peter7 時間: 2006-7-11 13:29
don't ever let the motor 空轉 too long because the rpm is too high. Try it on the car. If there is no overheat, your system is ok

作者: jasonwong 時間: 2006-7-11 13:37
Thank you.....Peter....

作者: ellis 時間: 2006-7-11 13:53

原帖由 jasonwong 於 2006-7-11 13:37 發表
Thank you.....Peter....

what's profile u choose on the gtb?
最終齒比又係多少?

作者: ellis 時間: 2006-7-11 13:55

原帖由 jasonwong 於 2006-7-11 12:10 發表
隻Novak 4.5R係新買既連GTB........

run完(無駁摩打齒空轉)熱到辣手既, 同埋行到某轉數個摩打就有d震+有唔唔聲(好似有d野頂住左咁)

Anyone can help me...??

bro.

你點樣run 隻motor?
駁好電吊半雞行數分鐘 or use other method?
can u tell me?

作者: lingkithung 時間: 2006-7-11 13:56
我都想知4.5r 可承受的齒比是多少, 因我也打算買!~thanks

作者: ellis 時間: 2006-7-11 14:01

原帖由 lingkithung 於 2006-7-11 13:56 發表
我都想知4.5r 可承受的齒比是多少, 因我也打算買!~thanks

說明書上有廠方建議, 4.5r 最好用9.幾至10.幾.(手上無說明書, 忘記實數)
有師兄叫我由10開始先.

作者: jasonwong 時間: 2006-7-11 16:31

原帖由 ellis 於 2006-7-11 13:53 發表

what's profile u choose on the gtb?
最終齒比又係多少?

the default one....jar
but I haven't try it on the track...because I just bought it yesterday....

about 9.8齒比la...

作者: jasonwong 時間: 2006-7-11 16:33

原帖由 ellis 於 2006-7-11 13:55 發表

bro.

你點樣run 隻motor?
駁好電吊半雞行數分鐘 or use other method?
can u tell me?

駁好電吊3/4雞行15mins....

作者: kawada 時間: 2006-7-11 16:49

原帖由 jasonwong 於 2006-7-11 16:33 發表

駁好電吊3/4雞行15mins....

I really dont think Brushless motor require any runin progress.. since it is " Brushless " .. Motor runin is to fine tune an appropriate match point between the brush and armature that BL dont have ..

I will recommend to lube your motor bearings ( both front & end bell 's ) before your first move is more important than " Run it In "

作者: jasonwong 時間: 2006-7-11 16:54

原帖由 kawada 於 2006-7-11 16:49 發表

I really dont think Brushless motor require any runin progress.. since it is " Brushless " .. Motor runin is to fine tune an appropriate match point between the brush and armature that ...

I will buy the bearings later....because I haven't play this BL system on track before....

作者: kawada 時間: 2006-7-11 18:40

原帖由 jasonwong 於 2006-7-11 16:54 發表

I will buy the bearings later....because I haven't play this BL system on track before....

No need to replace them if they didnt deform.. its guaranteed to be a nightmare .. just lube ( drop 2 to 3 drops of bearing oil onto the bearing of both ends will do ) them before u run it and after 10 to 20 packs of batteries.. then ur motor will stand much more longer ..

How to do that .. reference here

http://www.rcstudy.com/forum/viewtopic.php?t=2308

作者: jasonwong 時間: 2006-7-11 19:00

原帖由 kawada 於 2006-7-11 18:40 發表

No need to replace them if they didnt deform.. its guaranteed to be a nightmare .. just lube ( drop 2 to 3 drops of bearing oil onto the bearing of both ends will do ) them before u run it and af ...

Thank you.....

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)