RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區
標題: 終於砌好T3了 [打印本頁]
作者: hkdavidlam 時間: 2010-3-14 23:50
標題: 終於砌好T3了
多得咁多位師兄的幫作
t3終於砌好了
但仲未開始set車
麻煩各位師兄睇睇有無part整錯...thanks!
-
-
-
-
-
-
-
作者: hkdavidlam 時間: 2010-3-14 23:59
同埋~~~砌完之後...包0002...仲有好多零件剩下...正常嗎?
-
作者: kennywch 時間: 2010-3-14 23:59
車靚，電子嘢差，可惜！
作者: chestertai 時間: 2010-3-15 00:03
同埋~~~砌完之後...包0002...仲有好多零件剩下...正常嗎?
hkdavidlam 發表於 2010-3-14 23:59
spare parts
作者: mike20192 時間: 2010-3-15 00:04
同埋~~~砌完之後...包0002...仲有好多零件剩下...正常嗎?
hkdavidlam 發表於 2010-3-14 23:59
我都係咁!我林係比人做後備!
作者: hkdavidlam 時間: 2010-3-15 00:20
5# mike20192
唔該晒你們~~~thanks!
作者: hkdavidlam 時間: 2010-3-15 00:21
4# chestertai
原來係咁~~~我都安心d~~~
作者: Noir.KAZE 時間: 2010-3-15 08:32
可以的話
motor同電變擺埋d
個接收打棟擺
加返把motor fan
底板果3條黑色柱可以唔整落去
作者: hkdavidlam 時間: 2010-3-15 10:36
回復 8# Noir.KAZE
唔該晒~~~MOTOR FAN大約係點樣架?
因為我有多一把"ESC FAN"...岩用嗎?
作者: Noir.KAZE 時間: 2010-3-15 10:40
回復 Noir.KAZE
唔該晒~~~MOTOR FAN大約係點樣架?
因為我有多一把"ESC FAN"...岩用嗎?
hkdavidlam 發表於 2010-3-15 10:36
KWS有好多唔同裝風扇既motor heat sink賣
可以自己去睇
連唔連埋風扇買就自己諗啦(不過好多都連埋)
作者: skylegion 時間: 2010-3-15 13:52
無刷應該裝返個風扇
作者: totimothy 時間: 2010-3-15 13:55
樓主，你架車加埋電子野用左幾$
作者: memberbilly 時間: 2010-3-15 13:59
樓主會唔會仲用緊3003 servo呢
作者: totimothy 時間: 2010-3-15 14:06
唔會呱
3003 servo頂唔順，除非....佢用緊T1X/T2X摩打
作者: hkdavidlam 時間: 2010-3-15 14:48
回復 12# totimothy
car: $3250
5.5T motor+ 60A Esc: $700
towerpro mg 995 servo: $75
metal wheel + tire + insert: $160
receiver + transmite: use old one
作者: hkdavidlam 時間: 2010-3-15 14:54
回復 13# memberbilly
I am using towerpro mg 995 servo
It is ok for 5.5T motor...84T gear+20T motor gear?
作者: airwalk 時間: 2010-3-15 14:57
依家D RC 係XRAY 好過雙星?
作者: Noir.KAZE 時間: 2010-3-15 15:08
回復 memberbilly
I am using towerpro mg 995 servo
It is ok for 5.5T motor...84T gear+20T motor ...
hkdavidlam 發表於 2010-3-15 14:54
作者: hkdavidlam 時間: 2010-3-15 15:19
本帖最後由 hkdavidlam 於 2010-3-15 15:26 編輯
回復 18# Noir.KAZE
towerpro mg 995 servo
Size: 40.7mm X 19.7mm X 42.9mm
Weight: 55.0g
Operating Speed: 0.2sec/60 degrees (4.8V); 0.13sec / 60 degrees (6.0V)
Stall torque: 10.0kg/cm (180oz/in); 15kg/cm (208oz/in)
Temperature Range: 0 - 55 degrees
Dead band width: 10us
Operating Voltage: 4.8V - 7.2V
作者: rsx 時間: 2010-3-15 15:36
wow, the servo spec is too good for it's price. Is this real ?
作者: memberbilly 時間: 2010-3-15 17:01
玩車有d 野係可以慳,有d係唔可以
servo 同 tire就係唔可以
作者: totimothy 時間: 2010-3-15 21:16
回復 totimothy
car: $3250
5.5T motor+ 60A Esc: $700
towerpro mg 995 servo: $75
metal wheel ...
hkdavidlam 發表於 2010-3-15 14:48
5.5T...無感嗎??
同埋你樣樣野都唔係貴，但都有番幾百蚊,個servo $75，會唔會support唔到架野呀?
作者: hkdavidlam 時間: 2010-3-15 22:57
回復 22# totimothy
the motor is sensorless
the servo is ok so far
but the tire is so poor
it will detach from the wheel at high speed
The speed of car seem to be too fast....it is totally out of my expection
作者: hkdavidlam 時間: 2010-3-15 22:59
回復 21# memberbilly
C hing,
Any good suggestion about tire for T3
Thanks
作者: hk_sdu 時間: 2010-3-15 23:58
本帖最後由 hk_sdu 於 2010-3-16 00:00 編輯
Sorex 36R at this weather, almost no other choice
consider Yokomo M039 tire insert
plastic rims with AA glue ($2x for 4 rims)
作者: rsx 時間: 2010-3-16 00:14
回復 totimothy
the motor is sensorless
the servo is ok so far
but the tire is so poor
it wil ...
hkdavidlam 發表於 2010-3-15 22:57
You did not glue the tire to wheel?
Even if you use white pig motor, glue the tire to wheel is a must.
hk_sdu c-hing had already given a very good choice on tire. Depending on road condition and temperature, you may also need 32R or 40R (this is for rubber tire). Since T3 is a top end touring car, maybe you don't mind consider buying dedicated tire glue instead of AA (sorry I forgot the brand name, just ask the model shop owner and they will give you the right one)
Google on your low cost servo, ppls comments are mostly negative. Maybe you should also consider a better servo before it's too late. (maybe a cheap 3003 is a better choice).
作者: f-16 時間: 2010-3-16 00:14
話時話、T3可吾可以用TAMIYA的車頭海棉?
作者: hkdavidlam 時間: 2010-3-16 01:40
回復 26# rsx
I see~~~
I have a "TAMIYA CEMENT" for rubber Tires in my home~~~
Thanks for yours advice
作者: hkdavidlam 時間: 2010-3-16 01:43
用set車架set完架車了
T3...可以正式落地~~~
-
-
-
-
-
-
-
-
-
-
-
作者: hkdavidlam 時間: 2010-3-16 01:44
回復 27# f-16
sorry~~~我都唔知添~~
作者: hkdavidlam 時間: 2010-3-16 08:24
回復 25# hk_sdu
Thanks a lot...i will go to KWS Street to see see today
作者: 1524 時間: 2010-3-16 10:48
樓主.....
請問你玩T3之前, 仲玩過咩車?
唔知玩o既感覺, 兩者會唔會有好大分別?
作者: nick7 時間: 2010-3-16 11:03
樓主為架t3安全換過好少少既servo 同 tire啦
作者: 145240370 時間: 2010-3-16 11:14
呢條TIRE你唔會想玩架T3
你玩玩下會好冇心機
作者: hkdavidlam 時間: 2010-3-16 11:41
本帖最後由 hkdavidlam 於 2010-3-17 01:45 編輯
回復 32# 1524
我玩過df03ra呀
用hobbywing 35A esc + 9t brushless motor
部車都好好玩...不過...我覺得佢的steering的虛位太大
所以玩t3
作者: hkdavidlam 時間: 2010-3-16 11:42
回復 33# nick7
好...我今天去廣華街買
作者: hk_sdu 時間: 2010-3-16 12:40
If u play on street, this tire may be quite fun, but no performance on track. No need to buy good tire, it all depends on your purpose. T3 with good tire is not a must.
作者: hkdavidlam 時間: 2010-3-16 12:59
本帖最後由 hkdavidlam 於 2010-3-16 13:05 編輯
回復 37# hk_sdu
我其實諗住拿部T3來飛街
因我家樓下有一條大馬路....平時都無咩車...好好飛下
睇來...我條胎都可以用住先嗎?
作者: skylegion 時間: 2010-3-16 13:58
普通胎行都ok
作者: totimothy 時間: 2010-3-16 14:00
普通胎行? ok la
作者: hkdavidlam 時間: 2010-3-16 14:27
回復 39# skylegion
Yeah...thanks for yours reply and suggestion
作者: hkdavidlam 時間: 2010-3-17 00:52
今天買埋"車殼"了~~~完工
-
-
-
作者: milkboy 時間: 2010-3-17 10:11
david哥仔~~~
我見你地買架T3玩得咁開心...
都諗住買架黎玩
有時間大家研究一下
^^b
remark：個殼好靚喎~~~~現成野定係自己搞嫁 ^^~
作者: skylegion 時間: 2010-3-17 13:50
Take a Video !!!
作者: totimothy 時間: 2010-3-17 13:53
你個殼...講真,唔夠型
你起馬+ D LED燈 la
作者: hkdavidlam 時間: 2010-3-17 14:44
回復 43# milkboy
個殼...我係買...完成品的
好呀...大家一齊研究下
作者: hkdavidlam 時間: 2010-3-17 14:46
回復 45# totimothy
個殼係完成品
無得加野的
作者: hkdavidlam 時間: 2010-3-17 15:00
回復 44# skylegion
遲下有機會先拍啦
作者: console001 時間: 2010-3-17 21:31
SUBARU friend woh !
我又貼上來賀賀佢 !
