RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: gtb problem [打印本頁]

作者: ellis 時間: 2006-7-23 23:23
標題: gtb problem
各位brother,
小弟有少少關於GTB setting 既請教, 望你能俾少少advise過我.

我買左個gtb +4.5r, 第一時間係home set 左中位等正常情序,
但今day 係pyc 試車, 開車都無咩問題, 但去到一段後突然車子自行full 雞,
servo更自動偏向一邊, 情況有如 jam 機一樣(但絕不是jam機, 因我開住架車係pit位好耐都無事), 我第一時間致電求救,
我個fd 叫我將搖控(EX-1 MAR) reset 所有setting, 跟住 gtb 又再reset 多次試下,
不過都係一樣, 小弟想請用緊gtb既brother們請指點一下,
事關咩dead band, 咩freq. 我都未知咩黎, 唔知係咪要set sub-function先會正常.

many thx
ellis

(唔知關唔關擺位問題而產生干擾呢?)
有圖~

: 登錄/註冊後可看大圖

作者: leewui 時間: 2006-7-24 00:14
有也几钱呀

作者: SUNNY888 時間: 2006-7-24 00:25
你咁嘅情况似失控jam機喎.
呢個情况我諗同Dead Band 或者Drive frequency都冇關喎.
其實套GTB買番黎裝好之後應先做3個步驟.
1. 先set好支控. 照說明書講如ATV等先set好.
2. GTB set 中位.
3. 選擇GTB profile. 佢話factory set左1. 但最好自已set過.

至於 Dead Band , mini drive 等等睇下面.
http://bbs.rc-evo.com/viewthread ... 1&highlight=gtb

作者: oliver 時間: 2006-7-24 00:40

原帖由 ellis 於 2006-7-23 23:23 發表
各位brother,
小弟有少少關於GTB setting 既請教, 望你能俾少少advise過我.

我買左個gtb +4.5r, 第一時間係home set 左中位等正常情序,
但今day 係pyc 試車, 開車都無咩問題, 但去到一段後突然車子自行fu ...

試過一次
一比油就servo偏埋一邊...
原來排電個蕉插甩甩地有d接觸不良
之後換過排電就冇事...唔知係咪同你一樣

作者: binary 時間: 2006-7-24 08:35

原帖由 ellis 於 2006-7-23 23:23 發表
各位brother,
小弟有少少關於GTB setting 既請教, 望你能俾少少advise過我.

我買左個gtb +4.5r, 第一時間係home set 左中位等正常情序,
但今day 係pyc 試車, 開車都無咩問題, 但去到一段後突然車子自行fu ...

Hi Brother,
你既問題，小弟有時也會發生。但我唔係用 GTB, 只係普通 23T motor + 普通 ESC, PYC 直路有時會突然一o下會行左或行右！(結果當然係撞車啦

)。但小弟都覺得唔似 Jam 機 (Receiver is brand new)，試過場上得我一個人 on track 也有咁既問題！我都搵緊原因！可能真係上面兄弟講既蕉插問題也有可能！唉！什麼都要試o下。

作者: ernestf 時間: 2006-7-24 11:07
Hi

I had similar problem before ... mine was with a 10T brushed motor and when the tx is close to the rx (eg, at pit) it works fine but if I move away from the car, it get jams inconsistently. At the end, I did the following to resolve the problem (none of my radio gears has problem) :

(1) rewire the ESC such that the +/- wire is not close to and/or over the rx crystal position
(2) rewire the ESC such that the +/- batteries wire is not close to the rx antenna
(3) use something like that on the - motor wire and - batt wire to avoid / reduce interference

Hope this help.

: 登錄/註冊後可看大圖

作者: binary 時間: 2006-7-24 13:07

原帖由 ernestf 於 2006-7-24 11:07 發表
Hi

I had similar problem before ... mine was with a 10T brushed motor and when the tx is close to the rx (eg, at pit) it works fine but if I move away from the car, it get jams inconsistently. A ...

Thanks ernestf for your valuable experience.

BTW, what is the stuff (you circled it above) connected to the -ve motor wire? How should it call in Chinese or English? I may get it at KWS and have a try.

作者: ellis 時間: 2006-7-24 13:50
多謝咁多位brother 既advise 先~

問多樣, gtb 當set 好中位時, 除左紅燈長著外, 係咪仲有多兩色燈同時長著呢?
因我唔肯定~

thx

作者: ernestf 時間: 2006-7-24 14:34

原帖由 binary 於 2006-7-24 13:07 發表

Thanks ernestf for your valuable experience.

BTW, what is the stuff (you circled it above) connected to the -ve motor wire? How should it call in Chinese or English? I may get i ...

Hi Ellis

No thanks - the one is just clip on the - wire of the batt and motor, not soldered or connected ... etc. I am not sure how it called, perhaps some other members in the board can assist further.

Cheers
Ernest

作者: SUNNY888 時間: 2006-7-24 15:04

原帖由 ellis 於 2006-7-24 13:50 發表
多謝咁多位brother 既advise 先~

問多樣, gtb 當set 好中位時, 除左紅燈長著外, 係咪仲有多兩色燈同時長著呢?
因我唔肯定~

thx

set中位程序
1. 開搖控
2. 按住(set botton)開接收
3. 繼縝接住(set botton)直至紅燈左. (only red light)
4. 紅燈左就立刻放(set botton)
5. 將搖控推到full雞.住D燈會閃直到住綠燈.
6. 將搖控拉去剎車.燈直到綠燈閃.
7. 搖控回中,紅燈左. 攪掂

作者: ellis 時間: 2006-7-24 15:11
brother sunny888,

呢個小弟明白, 但我指當set 好哂中位後,
正式開個gtb, 除左紅燈外, 係咪仲有兩隻顏色燈(唔記得咩顏色, 但好似係最左果兩隻)係同紅色燈一齊長著呢?

作者: binary 時間: 2006-7-24 15:16

原帖由 ellis 於 2006-7-24 15:11 發表
brother sunny888,

呢個小弟明白, 但我指當set 好哂中位後,
正式開個gtb, 除左紅燈外, 係咪仲有兩隻顏色燈(唔記得咩顏色, 但好似係最左果兩隻)係同紅色燈一齊長著呢?

From my memory, it seems yes.

作者: kevin 時間: 2006-7-24 21:48
我想問點set 後波

作者: SUNNY888 時間: 2006-7-24 21:55

原帖由 ellis 於 2006-7-24 15:11 發表
brother sunny888,

呢個小弟明白, 但我指當set 好哂中位後,
正式開個gtb, 除左紅燈外, 係咪仲有兩隻顏色燈(唔記得咩顏色, 但好似係最左果兩隻)係同紅色燈一齊長著呢?

當你着左個GTB.  應該會有兩個燈號顯示.都係正常. (BRUSHED MODE 未試過, 吾知會吾會有其他燈號)

1.  藍,黃同紅燈着左.  表示在自定PROFILES. 即PROFILE(1-4)
2.  只有紅燈着.  表示在PROFILE5.

作者: SUNNY888 時間: 2006-7-24 22:11

原帖由 kevin 於 2006-7-24 21:48 發表
我想問點set 後波

只有PROFILE 2同5, 先至有後波.
而後波%係冇得set架.

作者: kevin 時間: 2006-7-25 22:23
點set做 PROFILE 2同5?

作者: ellis 時間: 2006-7-25 23:24

原帖由 kevin 於 2006-7-25 22:23 發表
點set做 PROFILE 2同5?

跟住說明書咁襟住個set button , 睇住d燈閃既次數一個一個咁落就得~
除非你唔明點set profile?

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)