RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 有關電車差速 [打印本頁]

作者: szsonggx 時間: 2010-7-29 10:14
標題: 有關電車差速
請問哪款電車差速防塵做得最好？油車就做得很好！

作者: 肥神 時間: 2010-7-29 10:24
如果有心玩車仔,好多人會用nt1牙差,做少少功夫,換少少零件,放落去,416
t3度,好過玩atomic果款(特別係416果隻)

作者: beebone 時間: 2010-7-29 10:39
回復 1# szsonggx

XRay

作者: sbman 時間: 2010-7-29 10:57
剛剛 download 左 XRAY NT1 個 manual 來睇
見到個 gear diff 係砌好左個 diff 先上 pulley
你地改落 416 時, 係咪砌好左個 diff 就上 416 個 pulley 去個 diff 度?

作者: beebone 時間: 2010-7-29 11:00

剛剛 download 左 XRAY NT1 個 manual 來睇
見到個 gear diff 係砌好左個 diff 先上 pulley
你地改落 416 ...
sbman 發表於 2010-7-29 10:57

登錄/註冊後可看大圖

oic, 你意思係牙差. 依家有plug and play牙差

作者: 肥神 時間: 2010-7-29 11:29
回復 4# sbman

YES~~就係鑼大個416PULLY,對番位置,上羅C,就得喇~
好COME行,又好用,不過呢,就用2粒細傘牙就得,唔洗用4粒,用4粒架車會比較唔定

作者: rcpop 時間: 2010-7-29 11:49
小弟新手一名...可否post d 相
講解安裝方法...
thanks!

作者: GigaRacer 時間: 2010-7-29 13:03

回復 sbman

YES~~就係鑼大個416PULLY,對番位置,上羅C,就得喇~
好COME行,又好用,不過呢,就用2粒細傘牙 ...
肥神發表於 2010-7-28 19:29

登錄/註冊後可看大圖

How about for Xray?

作者: GigaRacer 時間: 2010-7-29 13:21
Wait, should use NT1 front gear diff, right?

作者: sbman 時間: 2010-7-29 14:11
我諗肥神係講緊 NT1 front gear diff (前牙差)
睇 manual 後牙差同 pulley 係一件過
係前牙差先係差速同 pulley 分開

作者: 肥神 時間: 2010-7-29 14:50
我唔清楚,我無玩油車,我只不過係買一包XRAY牙差FOR NT1的
PART ON好像是35000.

作者: albylee 時間: 2010-7-29 19:23

回復 sbman

YES~~就係鑼大個416PULLY,對番位置,上羅C,就得喇~
好COME行,又好用,不過呢,就用2粒細傘牙 ...
肥神發表於 2010-7-29 11:29

登錄/註冊後可看大圖

ching 怎樣改呀我都想用NT1牙差改落416用呀可否話我知Thank

作者: stanley_wwy 時間: 2010-7-29 20:30
回復 9# GigaRacer

yes....it's to use the front diff.

the rear diff comes with a big pulley, won't fit in a EP car.

作者: GigaRacer 時間: 2010-7-30 00:15
OK, front NT1 diff + Xray pully.

How about the bearings? Any modification on that?

作者: hk_sdu 時間: 2010-7-30 01:09

回復 GigaRacer

yes....it's to use the front diff.

the rear diff comes with a big pulley, won ...
stanley_wwy 發表於 2010-7-29 20:30

登錄/註冊後可看大圖

The rear diff with pully, u can cut it away ma, it is just plastic.

作者: GigaRacer 時間: 2010-7-30 02:43
Any mod other than that? How about the bearing and outdrive cups? Do they fit?

作者: stanley_wwy 時間: 2010-7-30 04:09
回復 15# hk_sdu

? cut away?

then why not using the front diff in the first place?

作者: GigaRacer 時間: 2010-7-30 05:27

我唔清楚,我無玩油車,我只不過係買一包XRAY牙差FOR NT1的
PART ON好像是35000.
肥神發表於 2010-7-28 22:50

登錄/註冊後可看大圖

C hing, please take a close up picture of your gear diff.

Thank you very much!

作者: 天娜 時間: 2010-7-30 09:41
有無牙差可以改落軸車度, 如 TBevo5

作者: hk_sdu 時間: 2010-7-30 13:41

回復 hk_sdu

? cut away?

then why not using the front diff in the first place?
stanley_wwy 發表於 2010-7-30 04:09

登錄/註冊後可看大圖

Are u sure the front diff can fit?

作者: 肥神 時間: 2010-7-30 14:09
回復 18# GigaRacer [/隊

no problem~過1,2天我會放上來的~架車係車埸
作者: GigaRacer 時間: 2010-8-2 09:55
本帖最後由 GigaRacer 於 2010-8-1 18:37 編輯

C hing, got the picture yet?

NT1 front gear diff + pully.  Bearing will fit, right?  How about dog bones?

For T2/T3.  thanks!
作者: 肥神 時間: 2010-8-3 01:03
回復 22# GigaRacer
有相喇!!!!等好耐...唔好意思!!

登錄/註冊後可看大圖

登錄/註冊後可看大圖

登錄/註冊後可看大圖

登錄/註冊後可看大圖

登錄/註冊後可看大圖

作者: GigaRacer 時間: 2010-8-3 01:50
C hing, thank you so much!

Looks like it's the rear NT1 diff.
作者: 肥神 時間: 2010-8-3 01:55
回復 24# GigaRacer

係..無錯...呢隻係尾牙差
作者: GigaRacer 時間: 2010-8-3 02:08
I compared T2008 and NT1 manual.  Bearing size has no problem.  But I still think NT1 front diff maybe easier to make, at least no cutting on the diff.
作者: raman9551 時間: 2010-8-3 11:51
回復 26# GigaRacer

登錄/註冊後可看大圖

登錄/註冊後可看大圖

登錄/註冊後可看大圖

登錄/註冊後可看大圖

登錄/註冊後可看大圖

作者: GigaRacer 時間: 2010-8-3 12:22
Thank you C hing.

From the first picture: NT1 front diff, NT1 rear diff, and Spec R diff, correct?

So, should use NT1 rear diff, right?  Any change for the dog bones?  Thanks!
作者: raman9551 時間: 2010-8-3 12:28
回復 28# GigaRacer

但我見有人用NT1前差速呀, 你可去紅X攞老闆架車睇下, 佢用前差速嘅, 我T3就要用50mm狗骨
作者: GigaRacer 時間: 2010-8-3 12:37
my problem is..... i am not in HK.
作者: raman9551 時間: 2010-8-3 12:44
本帖最後由 raman9551 於 2010-8-3 12:45 編輯

回復 30# GigaRacer

你在...................加州
作者: GigaRacer 時間: 2010-8-3 13:30
Yes....

Here is the NT1 rear diff.  How do I cut it?

登錄/註冊後可看大圖

作者: GigaRacer 時間: 2010-8-3 13:39
here is the front NT1 diff.  Do the holes match with the 38T pully?  I know I need to cut the center part of the pully.  Thanks!

登錄/註冊後可看大圖

作者: raman9551 時間: 2010-8-3 14:48
對不起!我全是買二手回來的, 幫不了你答這問題, 要請其他ching幫手解答
作者: mike20192 時間: 2010-8-3 16:59

對不起!我全是買二手回來的, 幫不了你答這問題, 要請其他ching幫手解答
raman9551 發表於 2010-8-3 14:48

登錄/註冊後可看大圖

咁你2手反黎幾錢?
作者: raman9551 時間: 2010-8-3 17:31
回復 35# mike20192

$3xx
作者: 肥神 時間: 2010-8-3 18:08
回復 36# raman9551

如果你隻牙差係ANDY度買,那應該是TRC的其中一位C兄做的~
作者: gtimax 時間: 2010-8-3 20:36
must use rear diff nt1, use 磨機 , 磨去pulley90%餘下約2MM邊(等於T3 diff pulley內徑)
磨去t3 diff pulley內多餘的物料(可以塞入rear diff nt1)但要留4個孔上鏍絲
注意T3pulley其實騎住nt1 diff 邊0.5MM, 所以要加AA膠, 最後將T3 PULLEY膠圈吸回去,
,牙差杯磨闊D, OK晒!

登錄/註冊後可看大圖

登錄/註冊後可看大圖

作者: GigaRacer 時間: 2010-8-4 00:20
gtimax c hing, thanks for the great info.
作者: gtimax 時間: 2010-8-5 22:03
有唔明再問啦!

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/) Powered by Discuz! X3.2