RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Slash 新車開盒；請各高手多多指教 [打印本頁]

作者: dannychan 時間: 2010-8-21 23:34
標題: Slash 新車開盒；請各高手多多指教
本帖最後由 dannychan 於 2010-8-21 23:36 編輯

新入手 Slash Ultimate，打算全車打散再砌過，請問有那些地方要注意？

[attach]405098[/attach]

[attach]405099[/attach]

[attach]405100[/attach]

[attach]405101[/attach]

[attach]405102[/attach]

[attach]405103[/attach]

[attach]405104[/attach]

[attach]405105[/attach]

[attach]405106[/attach]

[attach]405107[/attach]

[attach]405108[/attach]

[attach]405109[/attach]

[attach]405110[/attach]

[attach]405111[/attach]

作者: sekwing211 時間: 2010-8-21 23:45
點解要打散再砌過

作者: dannychan 時間: 2010-8-21 23:55

點解要打散再砌過
sekwing211 發表於 2010-8-21 23:45

登錄/註冊後可看大圖

一來喜歡砌車；二來怕原廠流水線式組合有defect.

作者: alexman 時間: 2010-8-21 23:59

點解要打散再砌過
sekwing211 發表於 2010-8-21 23:45

登錄/註冊後可看大圖

了解架車既結構,有問題D易解決...

作者: gimsink 時間: 2010-8-22 00:07
打散再砌 not necessary la, Slash is assembled very good.
If you have time, change screw to stainless steel type la.
And if you have moer time, find some way to seal the space of main shaft ( both end ).
That's all you need to do.

作者: afu 時間: 2010-8-22 01:04
弓起晒!如果末落地的話,最好OP左個J concept overtray同#6860x先.我未用6860x之前爛左幾隻大齒魔打齒兩隻Bearing一隻中差一隻限滑

而家用之後就冇晒事Lu~~

作者: ThomasZ 時間: 2010-8-22 01:38
跑爛地的話,中差的啤鈴要經常檢查,如死左呢粒啤鈴繼續玩,會燒熔中差殼。

作者: dannychan 時間: 2010-8-22 14:54

打散再砌 not necessary la, Slash is assembled very good.
If you have time, change screw to stainle ...
gimsink 發表於 2010-8-22 00:07

登錄/註冊後可看大圖

Thank you for your advice. O.K. I will change the screw to stainless steel type.

作者: dannychan 時間: 2010-8-22 14:57

弓起晒!如果末落地的話,最好OP左個J concept overtray同#6860x先.我未用6860x之前爛左幾隻大齒魔打齒兩隻Be ...
afu 發表於 2010-8-22 01:04

登錄/註冊後可看大圖

請問#6860x motor mount 在那買？

作者: afu 時間: 2010-8-22 15:50
rcmart不過而家冇貨!ST Racing都有出可上A Main Hobbies訂!

作者: 22年 時間: 2010-8-22 16:46

Thank you for your advice. O.K. I will change the screw to stainless steel type.
dannychan 發表於 2010-8-22 14:54

登錄/註冊後可看大圖

又重又貴換黎仲乜？多餘。

作者: gimsink 時間: 2010-8-22 22:14
If you play the Slash in beach or some place that possibily be weted by salty water, then the screw will get rustly very fast (even you clean it after play), rustly screw will be difficult be taken off if you need repair later. 多餘 ??
[attach]405501[/attach]

作者: dannychan 時間: 2010-8-24 08:44

If you play the Slash in beach or some place that possibily be weted by salty water, then the screw ...
gimsink 發表於 2010-8-22 22:14

登錄/註冊後可看大圖

Totally agree !!

作者: tsk28 時間: 2010-8-24 09:21
其實本人都不太建議在海灘玩, 一來清洗麻煩, 二來就算洗完, d金屬都會生銹, 好麻煩

作者: kiev 時間: 2010-8-24 09:23
本帖最後由 kiev 於 2010-8-24 09:25 編輯

Totally agree !!
dannychan 發表於 2010-8-24 08:44

登錄/註冊後可看大圖

咁你快 d 去配埋不鏽鋼啤呤 ... 濕水玩車第一件瓜就係啤呤 !

作者: ThomasZ 時間: 2010-8-24 23:40
早兩日玩草地,有d草攝左入d轆的啤鈴到一齊磨,磨到塊藍色膠幾乎無哂,d沙塵入哂啤鈴。
用番普通啤鈴會唔會襟磨d? 塊藍色膠好似幫唔到手

作者: hlsk 時間: 2010-8-25 00:05

又重又貴換黎仲乜？多餘。
22年發表於 2010-8-22 16:46

登錄/註冊後可看大圖

E 位 Ching 一早話左自己玩車 is for fun with his children only. 所以做換乜都冇所謂. 但係架車一落鹹水, 換乜縲絲都死. 所有金屬野都會rusting.

Gimsink Ching please have a detail check with all bearings, motor shaft and gear box, hope they arent rusting or sanding yet, clean them immediately with wd40 or sell it out before everything breaks

作者: gimsink 時間: 2010-8-25 11:23
In my case, the main gear bearing get rusting seriously and the small bearing of the torque slipper a littel rust (a few round play in beach and even flush by lots tapwater after each play), I bought some replacement bearing in MK (not KWS) and grease-protect it and install back ( details in other post ). 3 round play in beach and no rust so far. All other bearings are OK wor, no rust at all !

作者: gimsink 時間: 2010-8-25 11:38
Turnbuckles and camber link also serious rust, go to SASA and buy a small bottle transperant finger nail oil, or pink/red etc...as you like ( high quality HK$25, cheap one HK$6, I buy cheap one ) and brush linkage 3-5 layesr to prevent rusting. That's it !
Gearbox protected by diff. oil, no rusting.
Motor shaft also rust, but " for fun with my boy only", forget about it !! haha.

作者: dannychan 時間: 2010-8-25 11:43
多謝各位師兄意見，過兩日得閒啲便開始做improvement，希望星期日可以第一次落地。

作者: Dinballian 時間: 2010-8-26 11:02
Note that the stainless screws are a bit softer then the stock steel screws and you will need a quality hex driver otherwise you will round out the screws.

作者: watchmanll 時間: 2010-8-29 23:15
好野呀....

作者: watchmanll 時間: 2010-8-29 23:17
好野呀....

作者: patrickli071 時間: 2010-9-3 17:43
請問樓主部車買左幾錢??

作者: dannychan 時間: 2010-9-3 20:11

請問樓主部車買左幾錢??
patrickli071 發表於 2010-9-3 17:43

登錄/註冊後可看大圖

買陣$3850，而家唔使啦

作者: patrickli071 時間: 2010-9-3 20:32
回復 25# dannychan

而家幾多左右??
同埋佢係咪一定要一set 咁買架??

作者: dannychan 時間: 2010-9-3 20:44

回復 dannychan

而家幾多左右??
同埋佢係咪一定要一set 咁買架??
patrickli071 發表於 2010-9-3 20:32

登錄/註冊後可看大圖

有幾個版本，齋車也有；請參考這裡：
http://www.rcmart.com/catalog/kits-traxxas-c-420_1196.html

作者: patrickli071 時間: 2010-9-3 22:28
回復 27# dannychan

咁你買係咪都係係呢個網度訂??

作者: kenji0316 時間: 2010-9-4 20:56
回復 1# dannychan

c兄想問下個殼係咪佢噴埋架?

作者: dannychan 時間: 2010-9-4 21:14
回復 28# patrickli071

No

作者: dannychan 時間: 2010-9-4 21:14
回復 29# kenji0316

Yes

作者: kenji0316 時間: 2010-9-4 21:23
回復 31# dannychan

你呢隻model6807?係包埋電.控同叉機?

作者: dannychan 時間: 2010-9-4 21:44
回復 32# kenji0316

http://www.rcmart.com/catalog/rc ... harger-p-31745.html

作者: kenji0316 時間: 2010-9-4 22:41
回復 33# dannychan

原廠控好用嗎?d電玩1次玩到幾耐?

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)