RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: New hand CRC Gen X questions [打印本頁]

作者: GigaRacer    時間: 2010-10-11 12:07
標題: New hand CRC Gen X questions
Just got an used CRC Gen X.  What's the different between Gen X and Gen XL?  Their website said Gen XL is for Lipo.  Is there any other major differences?
作者: jf813    時間: 2010-10-11 12:36
main different is the rear pod.  XL stand with open rear pod for brushless.  X is option.
作者: GigaRacer    時間: 2010-10-11 13:19
Does all newer 1/12 have standard tire mount?  Meaning it can fit with any 1/12 tires?
作者: GigaRacer    時間: 2010-10-11 13:43
Does this one have open rear pod?  Thanks!
作者: hardmankam    時間: 2010-10-11 19:35
回復 4# GigaRacer

Your car is a GenX with an open pod.
CRC can accept standard 1/12 pre-mount tires.
作者: move7648    時間: 2010-10-11 21:49
回復  GigaRacer

Your car is a GenX with an open pod.
CRC can accept standard 1/12 pre-mount tir ...
hardmankam 發表於 2010-10-11 07:35 PM


咩係pre-mount呔?
係唔係所有現成呔都要磨呔?
有無鋪頭代工?
作者: rcmodel    時間: 2010-10-11 22:02
樓主架車好熟口面wor  係咪2 手買架?
作者: hardmankam    時間: 2010-10-11 22:12
咩係pre-mount呔?
-> pre-mount 呔是指已glue,已cut 的呔 =  即買即玩, 現成呔
係唔係所有現成呔都要磨呔?
-> 現成呔可磨,可吳磨. 但磨呔優點是你可以控制呔的厚度.
有無鋪頭代工?
-> 不知道. 但應考慮買磨呔機.
作者: hardmankam    時間: 2010-10-11 22:14
樓主架車好熟口面wor  係咪2 手買架?
rcmodel 發表於 2010-10-11 22:02


樓主住在美國 wor
作者: rcmodel    時間: 2010-10-11 22:18
仲以為戚calvin果架 tim
幾時有局呀 我成兩個星期冇玩12仔
作者: move7648    時間: 2010-10-11 22:19
咩係pre-mount呔?
-> pre-mount 呔是指已glue,已cut 的呔 =  即買即玩, 現成呔
係唔係所有現成呔都要磨呔 ...
hardmankam 發表於 2010-10-11 10:12 PM


明白
唔磨的話, 唔係厚d, com行d咩?
作者: hardmankam    時間: 2010-10-11 22:26
回復 11# move7648

對,唔磨=com d,
不過磨了呔好行d.
作者: hardmankam    時間: 2010-10-11 22:31
回復 10# rcmodel

This sat?  Oct 16 2010?
作者: GigaRacer    時間: 2010-10-12 00:29
回復  GigaRacer

Your car is a GenX with an open pod.
CRC can accept standard 1/12 pre-mount tir ...
hardmankam 發表於 2010-10-11 03:35


Thank you C hing, again.
作者: rcmodel    時間: 2010-10-12 14:44
16 oct.  Ok. But 我好早會到around. 9:00
作者: hardmankam    時間: 2010-10-12 18:23
我 都 會 早 到 !




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/) Powered by Discuz! X3.2