RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 鋰電漲了= 就快壞??? [打印本頁]

作者: Samsunny    時間: 2010-11-8 10:17
標題: 鋰電漲了= 就快壞???
鋰電漲了= 就快壞???,  有乜方法鋪救????
Thanks
作者: @JOLY@    時間: 2010-11-8 10:29
放入垃圾桶吧如果你再玩要有心理準備佢會爆炸
作者: 日月天    時間: 2010-11-8 10:33
放入垃圾桶吧如果你再玩要有心理準備佢會爆炸
@JOLY@ 發表於 2010-11-8 10:29

Boom!!! Boom!!!!! Fire
作者: Samsunny    時間: 2010-11-8 11:04
真的這麼危險?????
有乜方法預防鋰電發漲???
作者: tomlaua31    時間: 2010-11-8 11:38
keep 50%-80%power,is ok
作者: chacha    時間: 2010-11-8 11:44
lipo over charge lithium  -->  lipo over charge lithium    
World's Most Dangerous Battery!  ---> World's Most Dangerous Battery!
Lipo 電 Spec:
***Storage***
Unlike certain other types of batteries, lithium polymer batteries can be stored for one or two months without significantly losing charge. However, if storing for long periods, manufacturers recommend discharging the battery to 40% of full charge. In addition, other sources recommend refrigerating (but not freezing) the cell

***Charging***
LiPoly batteries must be charged carefully. The basic process is to charge at constant current until each cell reaches 4.2 V; the charger must then gradually reduce the charge current while holding the cell voltage at 4.2 V until the charge current has dropped to a small percentage of the initial charge rate, at which point the battery is considered 100% charged. Some manufacturers specify 2%, others 3%, but other values are also possible. The difference in achieved capacity is minute.

Balance charging simply means that the charger monitors the voltage of each cell in a pack and varies the charge on a per-cell basis so that all cells are brought to the same voltage.

It is important to note that trickle charging is not acceptable for lithium batteries; Li-ion chemistry cannot accept an overcharge without causing damage to the cell, possibly plating out lithium metal and becoming hazardous. Most manufacturers claim a maximum and minimum voltage of 4.23 and 3.0 volts per cell 低過3V每片電就過放,這片電池就要說再見. Taking any cell outside these limits can reduce the cell's capacity and ability to deliver full rated current.

Most dedicated lithium polymer chargers use a charge timer for safety; this cuts the charge after a predefined time (typically 90 minutes).
作者: chiyuen    時間: 2010-11-8 12:07
請看我的 PM
作者: chiyuen    時間: 2010-11-8 12:19
如果是微 漲,不一定的,可以用义機 setting 到 LIPo MOD 放電每 Cell--3.00 V , 跟著 set 2 cell放電,用5-10A, 放完電隔1小時, 跟著用5A 充電, ( 最好义機有温度 sender, 可以看到電池了溫度,如有不正常,即時關义機和拔開插 ) ,如效果不理想,可以齊放電然後隔幾日,再充電,如沒改善可以放到垃圾桶.
還有不張電 過放或 over low,一舨可以放半個鐘,安全時為15分鐘,

  希望 可以幫得上
作者: ilove-benz    時間: 2010-11-8 12:23
有件肥肥地
今晚界開來看看內里是什麼鬼東西

作者: chacha    時間: 2010-11-8 12:43
本帖最後由 chacha 於 2010-11-8 12:46 編輯

watch this http://www.youtube.com/watch?v=6vYn2lbBh0Q

http://www.youtube.com/watch?v=T7A0HH_QyPE&feature=related

http://www.youtube.com/watch?v=6M5ftkN9PtY&NR=1&feature=fvwp
作者: zivtong    時間: 2010-11-8 12:52
除非真係漲得好勁
摸落去仲好實既
咁就唔好用啦

如果只係少少,可以摸到, 可以按下去,浮下浮下既,冇問題

如果真係掉,CUT左個插頭,用縮通包好,掉去鋰電回收箱啦,可以叫人開箱掉入去
好多MTR都有依個箱
作者: michealp    時間: 2010-11-8 13:06
如果是微 漲,不一定的,可以用义機 setting 到 LIPo MOD 放電每 Cell--3.00 V , 跟著 set 2 cell放電, ...
chiyuen 發表於 2010-11-8 12:19

"可以用义機 setting 到 LIPo MOD 放電每 Cell--3.00 V , 跟著 set 2 cell放電,"
唔明呢到.. 即係點?
即係先 set 1 cell 放電, 之後再 2 cell 放電?
咁同直接2 cell 放電有咩分別呢?
作者: michealp    時間: 2010-11-8 13:09
其實我有舊 by energy lipo 好得意的
我唔知係冷縮熱漲定點
正常玩, 冇過放, 次次一玩完就實漲的.. 禁落去係好"林"的, 好似有d 氣係入面咁
放一陣, 舊電一凍番就會正常番, 呢個情況已經好耐了
不過舊電本身已經唔係咁爆了
平時都係用來開 tire 行熱身圈用的
作者: 三寶    時間: 2010-11-8 13:57
其實同手提用ge 鋰電發漲係唔係一樣le,
我係唔理佢照用@@, 只係要成日差姐...
我又試過放佢入雪櫃, 又好似ok wor...
都唔知點解...haha

佢咁大電流, 都係小心為上la
作者: chiyuen    時間: 2010-11-8 17:41
sorry 寫漏1行應該是, 1 cell set 到 3v , 2 cell set 到 6v,
作者: chiyuen    時間: 2010-11-8 17:55
因為有 的义機 其本 setting 是這樣, 每 cell set 到 3v , 當放電時再 set 2 cell 义機會自動計算电壓,也會安全啲, 也可以到達要求的V數,
作者: sai20092001    時間: 2010-11-8 22:10
YS~...漲左=冇得救..要作好準備!!
作者: bravohk    時間: 2010-11-8 22:28
不過這裡經常有人把微脹/大脹的鋰電放上二手區, 是否有必要管制下?
作者: chiyuen    時間: 2010-11-8 23:37
好意見呀,如果是真的,一些新手用家買了這...................風險很高!!!!!!!!!!!!!
作者: lazer    時間: 2010-11-9 00:20
放入垃圾桶吧如果你再玩要有心理準備佢會爆炸
@JOLY@ 發表於 2010-11-8 10:29 AM


放入垃圾桶前仲要做d野先, 請看以下棄置li-po的標準程序:
http://www.rctoys.com/pdf/thunde ... -lipo-batteries.pdf




歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/) Powered by Discuz! X3.2