RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Walkera #76 [打印本頁]

作者: kschan 時間: 2006-8-16 21:47
標題: Walkera #76
Hi !! Is Walkera#76 good for beginner ?

I like it because its strong frame. Pls comment !!

作者: 小步 時間: 2006-8-16 22:55
SAME AS WALKERA #4, FP machine

But got more easier demage when your crash coz the rotation speed is higher then Walkera 4
Also new machine the repair cost is higher then Walker 4

But no need to modifty and just adjust less pitch(about 8degrees) will got more stable on hovering.
More easier to modifty burshless system coz the main flame have stronger the Walker4

作者: kschan 時間: 2006-8-16 23:42
when compared with E-sky 004, which one is better ?

作者: 小步 時間: 2006-8-17 18:39
Frankly Speaking, when all is original

Walkera 4 performanceis better then then EK004,but Esky 's electronic is more stable then Walkera's one
Walkera products got very bad QC and always got problems when you buy a bad quility one.

作者: kschan 時間: 2006-8-17 19:51
Thank you !!

I bought walkera #76 yesterday,  could anyone tell me where I can buy the cheapest part for this heli ?
I found this heli was similiar to #22.  Is #22's part compatible with #76.  Moreover, how to modify this heli
to brushless motor and control.
I found this heli was more easily to hover.  I like this heli and hope it will be more stable and reliable.

作者: zipdrive 時間: 2006-8-18 10:16

原帖由 kschan 於 2006-8-17 19:51 發表
Thank you !!

I bought walkera #76 yesterday, could anyone tell me where I can buy the cheapest part for this heli ?
I found this heli was similiar to #22. Is #22's part compatible with #76. ...

How much, Where to buy ???

作者: 小步 時間: 2006-8-18 11:40
imcompatible parts with #22
I don't know when can buy parts in HK , maybe in Ap Lu St.
no need to modifly brushless 1st, try to use 1300MAH 10C or higher lipo batterys and tune down about at +7~+8 degrees on the main blades and try .

作者: kschan 時間: 2006-8-18 23:38
hk$ 600 in Au Lu St.
Can I use 11.1 or 7.4 lipo ?
Is there any tool recommended to check the main blade angle?

作者: zifu 時間: 2006-8-19 11:45
#22 spare parts problem

作者: 小步 時間: 2006-8-19 14:59
YES, Sure

Aslo #76 must use 11.1V then can get the better performance.
If use 7.4V Lipo light weight batt , will cause very unstable
Also Hearvy weight batt are not suggested, 880MAH 7.4V or 1300MAH 11.1V 10C or higher is enough.

P.S. batter replace the tail motor to [NS60] when your tail motor become unstable.coz 11.1V causeing yr original motor hearvy loading

作者: kschan 時間: 2006-8-22 14:34
help !!
Just crashed by accident

pls tell me where can i buy the rotor shaft and main shaft and how much ?
Thank you !!

作者: kschan 時間: 2006-9-1 14:41
Any other main blade are suitable for #76 ? Pls recommend !!

作者: 小步 時間: 2006-9-1 14:46
fm now i can't find any blades suitable for #76

Only can buy original one

作者: kschan 時間: 2006-9-1 14:48
Thank you !!

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)