RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Pan Car Galaries ^^ [打印本頁]

作者: mikuro 時間: 2011-2-1 11:55
標題: Pan Car Galaries ^^
本帖最後由 mikuro 於 2011-2-5 00:59 編輯

Hello all Pan Car Ching

Would you mind sharing your finished pan car (1/10 or 1/12, 扮Pro Ten 都得架), on and off shell here? ^^

Hope more Ching will join the Pen Car party !!!

Thank you very much !!!

作者: mikuro 時間: 2011-2-1 12:09
Here is my Xray XII link car

作者: hlsk 時間: 2011-2-1 13:35
好靚，但個幾條摩打線頂住左條油壓，會阻住扭腰

作者: mikuro 時間: 2011-2-1 13:52

好靚，但個幾條摩打線頂住左條油壓，會阻住扭腰
hlsk 發表於 2011-2-1 13:35

登錄/註冊後可看大圖

Hi Ching, my cable layout is not looking good but I have no issue on the damper since there is room under the body shell for the cables ^^

作者: hlsk 時間: 2011-2-1 14:43
回復 5# mikuro

Thz Ur call, btw, where and when u will ground it? Interest to c how it performs.

作者: derek5 時間: 2011-2-1 14:57
本帖最後由 derek5 於 2011-2-1 15:17 編輯

小小意見，個ESC線換16G，幼D，軟好多，減少對扭腰影響，原裝的太粗，太硬了，12仔可以幼D。用放在中間是ok的，因為成個12仔殼最高位就是中間，唔會頂住個殼(唔平)，另外，所有電線的長度要小心處理，長短得宜，才不會影響扭腰，有錯請指教，謝謝!

作者: mikuro 時間: 2011-2-1 15:00

回復 mikuro

Thz Ur call, btw, where and when u will ground it? Interest to c how it performs.
hlsk 發表於 2011-2-1 14:43

登錄/註冊後可看大圖

Normally, me and some Ching will play at JV on weekend. If you have 2WD car as well, you can join the party as well. ^^

作者: mikuro 時間: 2011-2-1 15:04
本帖最後由 mikuro 於 2011-2-1 15:06 編輯

小小意見，個ESC線換16G，幼D減少對扭腰影響，原裝的太粗，太硬了，12仔可以幼D。用放在中間是ok的，因為成 ...
derek5 發表於 2011-2-1 14:57

登錄/註冊後可看大圖

Hi Derek, it is good to see more pan car coming. Your CRC is looking great ^^
Can you show us your shell as well?
Yes, even the built-in cable is still okay but I agree to change to thinner cables. Thanks for sharing ^^
Btw, are you using 4.5T motor? Have you play at JV before? ^^

作者: derek5 時間: 2011-2-1 15:14
回復 9# mikuro

no, i'm living in YL, will go to TC or TRC in sometime.....

作者: derek5 時間: 2011-2-1 15:18

Hi Derek, it is good to see more pan car coming. Your CRC is looking great ^^
Can you ...
mikuro 發表於 2011-2-1 15:04

登錄/註冊後可看大圖

i'm using 4.5T and want to try 4.0T later, how about you?

作者: mikuro 時間: 2011-2-1 15:27
本帖最後由 mikuro 於 2011-2-1 15:28 編輯

回復 mikuro

no, i'm living in YL, will go to TC or TRC in sometime.....
derek5 發表於 2011-2-1 15:14

登錄/註冊後可看大圖

Alright then ^^
Nice shell. Thanks for sharing ^^

作者: mikuro 時間: 2011-2-1 15:29

i'm using 4.5T and want to try 4.0T later, how about you?
derek5 發表於 2011-2-1 15:18

登錄/註冊後可看大圖

I am using X12 4.0T ^^

作者: hlsk 時間: 2011-2-1 16:25
回復 8# mikuro

Thx for the invitation and love to grasp some knowledge from Ching like u

作者: mikuro 時間: 2011-2-1 16:33
本帖最後由 mikuro 於 2011-2-1 16:37 編輯

回復 mikuro

Thx for the invitation and love to grasp some knowledge from Ching like u
hlsk 發表於 2011-2-1 16:25

登錄/註冊後可看大圖

Tell you what, I am a beginner and I just picking up 1/12 pan car again since JV was born. ^^
Also, there are Ching here that sharing a lot more information on pan car as well.

作者: raymomo 時間: 2011-2-2 00:06
回復 1# mikuro

First time show my F104 pan car here!! haha and some shell of 1/10 pan car[attach]460425[/attach][attach]460426[/attach][attach]460427[/attach][attach]460428[/attach][attach]460429[/attach][attach]460430[/attach][attach]460431[/attach][attach]460432[/attach][attach]460433[/attach][attach]460434[/attach][attach]460435[/attach][attach]460436[/attach][attach]460437[/attach]

作者: mikuro 時間: 2011-2-2 00:10

回復 mikuro

First time show my F104 pan car here!! haha and some shell of 1/10 pan car
raymomo 發表於 2011-2-2 00:06

登錄/註冊後可看大圖

Thanks Ray for sharing. ^^
Seems you wanna to get Corally Pro Ten as well. GoGoGo ^^

作者: abcde 時間: 2011-2-2 00:15

回復 mikuro

First time show my F104 pan car here!! haha and some shell of 1/10 pan car
raymomo 發表於 2011-2-2 00:06

登錄/註冊後可看大圖

very nice....f37 r35 ?
f104 have a abc leman shell....if use normal oil car tire...it good fit (180mm width) as I saw one ching try before.....it is good because large range oil car tire degree can choice and more cheap.....speedmind oil tire only $90 1 set.......

作者: abcde 時間: 2011-2-2 00:23
show some of mind...but now all are dirty and some is retire...
they are f109..f103..f103GT....ae 12r5 ......

作者: raymomo 時間: 2011-2-2 00:24
回復 17# mikuro

already have waiting list in red star!! but one big trouble thing is the parts problem,need to ask them more details about it!! pick up u CRC already?

作者: raymomo 時間: 2011-2-2 00:25
回復 18# abcde

yes ar F37 F35! any other choice of the more solf rear tire??

作者: abcde 時間: 2011-2-2 00:30

回復 abcde

yes ar F37 F35! any other choice of the more solf rear tire??
raymomo 發表於 2011-2-2 00:25

登錄/註冊後可看大圖

now only this choice....i also ask those shop have more hard front and more soft rear...they say only this.....rear 35 is ok and if can find front 40 is more better....
uncle chan may have another brand but i haven't try ....it may have differnt degree...
btw....you just need change shell to abc then can use normal oil car tire....

then thousand of soft and hard can choice....

作者: raymomo 時間: 2011-2-2 00:34
回復 22# abcde haha tonight i try this shell for test run , it is really really good fit for now[attach]460471[/attach]

作者: mikuro 時間: 2011-2-2 00:51
本帖最後由 mikuro 於 2011-2-2 00:54 編輯

回復 mikuro

already have waiting list in red star!! but one big trouble thing is the part ...
raymomo 發表於 2011-2-2 00:24

登錄/註冊後可看大圖

今日收到電話到貨 ^^
Thanks Wai gor since I nearly forgot to buy those allen wrench tonight ^^

作者: raymomo 時間: 2011-2-2 00:59
回復 24# mikuro

one important thing u didnt buy??

作者: mikuro 時間: 2011-2-2 01:01

回復 mikuro

one important thing u didnt buy??
raymomo 發表於 2011-2-2 00:59

登錄/註冊後可看大圖

Ray 兄, please advise. Thanks !

作者: raymomo 時間: 2011-2-2 01:01
本帖最後由 raymomo 於 2011-2-2 01:04 編輯

[attach]460507[/attach]回復 26# mikuro

4mm Rear Top Plate !

作者: mikuro 時間: 2011-2-2 01:11

回復 mikuro

4mm Rear Top Plate !
raymomo 發表於 2011-2-2 01:01

登錄/註冊後可看大圖

Just check out that the original one is about 2.5mm.
Is this easily broken so you suggest to get the 4mm option part?

作者: raymomo 時間: 2011-2-2 01:15
回復 28# mikuro

yes!! very easily broken, must change item!!haha

作者: mikuro 時間: 2011-2-2 01:16

回復 mikuro

yes!! very easily broken, must change item!!haha
raymomo 發表於 2011-2-2 01:15

登錄/註冊後可看大圖

Noted and thanks ^^

作者: billlkyy 時間: 2011-2-2 03:06
我又來.....

作者: mikuro 時間: 2011-2-2 03:20

我又來.....
billlkyy 發表於 2011-2-2 03:06

登錄/註冊後可看大圖

Morning Bill, thanks for sharing your ride ^^

作者: hairy 時間: 2011-2-2 08:42
my car.....

作者: mikuro 時間: 2011-2-2 09:43
本帖最後由 mikuro 於 2011-2-2 09:49 編輯

my car.....
hairy 發表於 2011-2-2 08:42

登錄/註冊後可看大圖

This is the Legendary Rocket in JV >_<
Can you tell us what turn is the motor?
What is the gear ratio?

作者: hairy 時間: 2011-2-2 10:26
4600kv 20/96 3s

作者: lky2000 時間: 2011-2-2 11:35

my pancar series

作者: 1524 時間: 2011-2-2 11:43
回復 36# lky2000

I LIKE THE PORSCHE VERY MUCH!!!

作者: lky2000 時間: 2011-2-2 11:53
thanks 1524 ching PORSCHE chasiss is trc pro12

作者: 1524 時間: 2011-2-2 13:20

thanks 1524 ching PORSCHE chasiss is trc pro12
lky2000 發表於 2011-2-2 11:53

登錄/註冊後可看大圖

thank for your sharing.
可惜之前對12仔無咩興趣,
所以錯過左好多古董12仔.
不過睇幾個ching分享d舊12仔, 真係覺得舊12o既設計各有特色. 好精彩!!!

作者: mikuro 時間: 2011-2-2 14:07

my pancar series
lky2000 發表於 2011-2-2 11:35

登錄/註冊後可看大圖

Very nice collection ^^

作者: BT 時間: 2011-2-2 15:20
So good Pan car

作者: gon628 時間: 2011-2-2 18:40
Ching speedmind oil tire where to buy ... thx

作者: abcde 時間: 2011-2-2 21:09

Ching speedmind oil tire where to buy ... thx
gon628 發表於 2011-2-2 18:40

登錄/註冊後可看大圖

ching.....uncle chan should have..."good view" model...last time i buy f42 r40....$90 1 set......
and i think f40 r37.....or f37 r35....also OK depend on how fast your car....more fast need more soft....

作者: abcde 時間: 2011-2-2 21:13

ching.....uncle chan should have..."good view" model...last time i buy f42 r40....$90 1 set......
...
abcde 發表於 2011-2-2 21:09

登錄/註冊後可看大圖

if you are f103GT/f104 change to GT (use front and rear hex )....you will only have 180mm width...you need that ABC shell wihich for f104 change to play leman....
that shell around 180mm width.....

作者: teamlosi 時間: 2011-2-3 08:44
本帖最後由 teamlosi 於 2011-3-7 22:12 編輯

買了很久唔知重有冇parts。

作者: JohnnyC 時間: 2011-2-4 04:03
回復 45# teamlosi

Wow...nice vintage Corally....but I dun think easy to get parts lu.....!

作者: emaxxyeung 時間: 2011-2-4 09:45
呢部corally c10,我都有部,

作者: mikuro 時間: 2011-2-4 10:04

買了很久唔知重有冇parts。
teamlosi 發表於 2011-2-3 08:44

登錄/註冊後可看大圖

Very nice vintage Pro Ten !!!
Thanks for sharing ^^

作者: gon628 時間: 2011-2-4 23:45
thx....but where is Uncle Chan.....

作者: abcde 時間: 2011-2-6 00:17
回復 49# gon628
陳叔...好景....

作者: mikuro 時間: 2011-3-5 09:02
本帖最後由 mikuro 於 2011-3-5 09:24 編輯

Here is the trial run for my CRC GX10 LE with 1S + SXX v2 + 4.0T octa at end of FEB 11

Now will switch to 2S and test again soon

作者: joesheng 時間: 2011-3-5 14:32
Very nice~
Cool~~~

作者: photocatcher 時間: 2011-3-5 22:47
[attach]471908[/attach][attach]471909[/attach][attach]471911[/attach][attach]471910[/attach][attach]471912[/attach]

作者: airyu 時間: 2011-3-6 23:32
my S120L ,, finally got my king pin

作者: airyu 時間: 2011-3-6 23:37
again my S120L

作者: lung1 時間: 2011-3-6 23:53

my S120L ,, finally got my king pin
airyu 發表於 6/3/2011 11:32 PM

登錄/註冊後可看大圖

nice photo~

作者: airyu 時間: 2011-3-7 07:35
thank you

作者: 1524 時間: 2011-3-7 22:58

again my S120L
airyu 發表於 2011-3-6 23:37

登錄/註冊後可看大圖

nice car.
waiting for your comment on this rocket!

作者: raymomo 時間: 2011-3-7 23:00
回復 55# airyu

like your shell!! so nice!

作者: airyu 時間: 2011-3-7 23:05
thank you

作者: lucky88lucky 時間: 2011-3-8 15:59
正到暈

作者: billck1 時間: 2011-3-12 00:37
[attach]474111[/attach][attach]474112[/attach]

放大假終於砌好啦。多多指教！

作者: billck1 時間: 2011-3-12 01:19
回復 2# mikuro

CHING，AMR對車頭燈貼紙係唔係要另外買？

作者: mikuro 時間: 2011-3-13 11:46

回復 mikuro

CHING，AMR對車頭燈貼紙係唔係要另外買？
billck1 發表於 2011-3-12 01:19

登錄/註冊後可看大圖

No. There is no lamp decals in the pack and they do not have lamp decals for sale as well.

作者: billck1 時間: 2011-3-15 08:46
回復 64# mikuro
CHING多謝回覆
你部XRAY 12仔頭轆轉向每邊幾多度？
重有你話set toe out 1度好唔好？

作者: mikuro 時間: 2011-3-15 08:53
本帖最後由 mikuro 於 2011-3-15 11:13 編輯

回復 mikuro
CHING多謝回覆
你部XRAY 12仔頭轆轉向每邊幾多度？
重有你話set toe out 1度好唔好？
billck1 發表於 2011-3-15 08:46

登錄/註冊後可看大圖

Mine mostly play at JV so I set the steering to about 45, for both sides.

If you find your ride is understeering, you may
1. using tire additives
2. increase the steering angle
3. set toe-out , about 1 degree is ok.

作者: pcm118 時間: 2011-3-15 09:40
you can also set the steering to maximum without binding, then use the dual rate in your transmitter to reduce the angle on course. I use only around 40%, with 1 degree toe-out and 1.5 degree camber, 呔水 on inner half at front and full at rear

作者: nel3838 時間: 2011-3-15 12:28

very nice....f37 r35 ?
f104 have a abc leman shell....if use normal oil car tire...it good fit (1 ...
abcde 發表於 2011-2-2 00:15

登錄/註冊後可看大圖

Hi ABCDE CHing, Yes, I have the ABC Leman shell (Response GT430), and fitted with Ride 104 tyres, so it is 180mm.

But how do you get F104 to use Oil Car tyres (foam I guess) to fit 180mm Leman shell? thx.

作者: abcde 時間: 2011-3-15 21:48

Hi ABCDE CHing, Yes, I have the ABC Leman shell (Response GT430), and fitted with Ride 104 tyre ...
nel3838 發表於 2011-3-15 12:28

登錄/註冊後可看大圖

mine is a f103GT.....not a f104.....i use 220mm oil car tire F/R and it then change from a 18xmm become a 200mm size...

作者: nel3838 時間: 2011-3-15 22:50
本帖最後由 nel3838 於 2011-3-15 22:55 編輯

very nice....f37 r35 ?
f104 have a abc leman shell....if use normal oil car tire...it good fit (1 ...
abcde 發表於 2011-2-2 00:15

登錄/註冊後可看大圖

Thx ABCDE, here are mine two 假 Ten (不是好Pro) 供显 ....

enjoy...

[attach]475566[/attach]
[attach]475567[/attach]

Link for more photos on the 104
http://bbs.rc-evo.com/viewthread.php?tid=209314&extra=page%3D1

作者: Maxsl3 時間: 2011-3-15 23:29
回復 64# mikuro

Miko.. As mention, pls take a look .. see how you comment on my S100, I find very difficult to control after 3 laps running. thz

http://www.youtube.com/watch?v=eD8FuBbjFO4

作者: nel3838 時間: 2011-3-17 06:26

回復 mikuro

Miko.. As mention, pls take a look .. see how you comment on my S100, I find very d ...
Maxsl3 發表於 2011-3-15 23:29

登錄/註冊後可看大圖

Curious, it ran very fast on first couple laps, but later seems something got loose..... but nice and fast

作者: mikuro 時間: 2011-3-17 07:00

回復 mikuro

Miko.. As mention, pls take a look .. see how you comment on my S100, I find very d ...
Maxsl3 發表於 2011-3-15 23:29

登錄/註冊後可看大圖

Hi Alex, as discussed yesterday, you can try changing the diff nut in next run. ^^

作者: Maxsl3 時間: 2011-3-17 11:33
回復 73# mikuro

Hi Mike,, thanks so much for your comment ,. as discussed, I confirmed the rear transmission nut problem.. thopefully i would see you soon at JV and share the result then..thanks

作者: Maxsl3 時間: 2011-3-17 11:34
回復 72# nel3838

Thanks.. actually if the car is in proper setting, its run really fast and easier control compare to 4WD.

作者: nel3838 時間: 2011-3-17 13:10

回復 nel3838

Thanks.. actually if the car is in proper setting, its run really fast and e ...
Maxsl3 發表於 2011-3-17 11:34

登錄/註冊後可看大圖

wow even faster comparing with 4WD, that's great

作者: abcde 時間: 2011-3-17 22:36

Hi Alex, as discussed yesterday, you can try changing the diff nut in next run. ^^
mikuro 發表於 2011-3-17 07:00

登錄/註冊後可看大圖

Hi Mic...me, fyin and 3rock should play car on sat morning ...will you join ?

作者: nel3838 時間: 2011-3-17 22:49

Hi Mic...me, fyin and 3rock should play car on sat morning ...will you join ?
abcde 發表於 2011-3-17 22:36

登錄/註冊後可看大圖

What time CHing Sat morning?

PS: fyi actually I tried Sat night, seem more 2WD at night.......

作者: abcde 時間: 2011-3-17 23:09
around 10am to 10:30am start...

作者: mikuro 時間: 2011-3-18 10:11

Hi Mic...me, fyin and 3rock should play car on sat morning ...will you join ?
abcde 發表於 2011-3-17 22:36

登錄/註冊後可看大圖

Hi Wai gor, however, I may not be at JV early morning but I will try to see if I could fit in the schedule later on SAT.

作者: abcde 時間: 2011-3-18 20:45

Hi Wai gor, however, I may not be at JV early morning but I will try to see if I could fit ...
mikuro 發表於 2011-3-18 10:11

登錄/註冊後可看大圖

rain.rain....rain......

作者: mikuro 時間: 2011-3-18 21:05

rain.rain....rain......
abcde 發表於 2011-3-18 20:45

登錄/註冊後可看大圖

No worries, sunny day will come again

作者: nel3838 時間: 2011-3-19 00:31

No worries, sunny day will come again
mikuro 發表於 2011-3-18 21:05

登錄/註冊後可看大圖

Sunny day on Sunday maybe?

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)