RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Setting of Asso 12R5 [打印本頁]

作者: st_kuen 時間: 2011-3-17 13:25
標題: Setting of Asso 12R5
Any c-hing can share the following setting experience (Say, the setting in JV):

1) What is the depth of the set screw should be screw into the chassis brace (say, using silver side spring)?
2) What is the position of the shock collar should be place in the shock body? (It will affect the angle between chassis and lower motor plate)

thank in advance!!

作者: kawada 時間: 2011-6-12 01:28
本帖最後由 kawada 於 2011-6-12 22:47 編輯

Download the following pdf from Xray, It provide detail setup reference and suit all pan cars

http://www.teamxray.com/teamxray/showfile.php?file_id=5057

作者: joesheng 時間: 2011-6-12 10:48
Thanks for your information~

作者: FATYUEN83 時間: 2011-6-12 11:56
Thanks for your information too~

作者: jf813 時間: 2011-6-13 11:38
side screw usually very little or no preload. Especially if you use hard spring like silver.... center spring adjust it so the chassis is flat with rear pod. If center a little higher than rear pod will give a little more rear grip. But the car is less "predictable" when the rear end start to loose grip.

作者: st_kuen 時間: 2011-6-14 23:14
Many thanks for Kawada & jf813 c-hing!!

作者: levinng 時間: 2011-7-2 16:06
我架associate 5.1 有d推頭情况, 各位ching，頭彈弓用咩度數呢

作者: joesheng 時間: 2011-7-2 16:17
你用speedmind?
如果係既話,你試下換呔先~

作者: levinng 時間: 2011-7-2 18:23
回復 joesheng 的帖子

真係咁差?我見幾多Ching 用...

作者: levinng 時間: 2011-7-3 00:23
回復 levinng 的帖子

有用呔水呀，咁唯有開套matrix 試下啦..... ching 用開邊隻呔呢?

作者: joesheng 時間: 2011-7-3 00:50
回復 levinng 的帖子

Xceed F/M R/M,very good codition~

作者: joesheng 時間: 2011-7-3 00:51
F/50% tire water,R/100%,
TRY TRY~

作者: levinng 時間: 2011-7-3 02:08
回復 joesheng 的帖子

Try try sin... Thanks ching!

作者: vin00002002 時間: 2011-7-18 02:33
If all original without option parts and tire water, can it run fast in good control?

作者: levinng 時間: 2011-7-18 03:41
回復 vin00002002 的帖子

Understeering if no tyre water. Btw if u play slow motor (eg.. 1cell +5.5T or 2 cell + 10.5T) there will be no impact to you.

作者: levinng 時間: 2011-7-18 15:55
回復 joesheng 的帖子

已經解決推頭問題，原來我其中一邊A臂粒波子上下調轉左, 衣家用番speedmind 頭中尾中完全冇問題.

作者: vin00002002 時間: 2011-7-26 01:12
wanna play S120 with 60a + 5.5T + 2 cell, is that ok? seems nothing to set on 12 son but do i need to set anything? like spring, camber, tow in-out, ride height?

作者: dxmaxian 時間: 2011-7-26 08:59
回復 jf813 的帖子

Side sprin is very funny, You can chose useing preload or not, And with preload you will get 2 times hardness than non-preload

作者: jf813 時間: 2011-7-26 09:51

dxmaxian 發表於 2011-7-26 08:59

登錄/註冊後可看大圖

回復 jf813 的帖子

Side sprin is very funny, You can chose useing preload or not, And with preload y ...

ya... just personally I don't really like to add lot of preload as this makes the steering too fast, not very stable. I prefer to change to harder spring if necessary. Just my 2 cents

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)