RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: HY 120A-1S 晤落散熱? [打印本頁]

作者: eyhpoon 時間: 2011-3-21 11:51
標題: HY 120A-1S 晤落散熱?
發覺裝好盁 120A-1S 落 CRC GEN XL & PROTOFORM AMR-12殼, 如果加ESC散熱會頂住個殼,
(準備用1S LIPO + 4.5T)

見過有的外國12仔比賽都無用散熱 (不過係TEKIN, NOSRAM)

有無師兄試好盁 120A-1S晤落散熱有無問題?

作者: kay1926 時間: 2011-3-21 12:10
先 check check full load ( 1s lipo + 4.5 T )幾多 amp 先？

作者: jf813 時間: 2011-3-21 12:11
I use 3.5t and ESC is very hot... 70 degree+. Just tape the fan onto the ESC will help. And will be able to clear the AMR body.

作者: eyhpoon 時間: 2011-3-21 13:02

I use 3.5t and ESC is very hot... 70 degree+. Just tape the fan onto the ESC will help. And will ...
jf813 發表於 2011-3-21 12:11

登錄/註冊後可看大圖

C-Hing, you mean just fan with no heatsink?
My problem is I cannot install the heatsink at all.
Thx

作者: jf813 時間: 2011-3-22 03:07
回復 4# eyhpoon

yes, no heat sink. Just tape the fan onto the esc. It should fit wor. I am running r5 with amr body.

作者: eyhpoon 時間: 2011-3-22 23:26
本帖最後由 eyhpoon 於 2011-3-23 01:26 編輯

我而家既Layout:

登錄/註冊後可看大圖

HY-120A-1S比較大,打橫會頂住side link.而家謂有打直放散熱靠出 (右邊). 但靠出個AMR12殼比較低身,剩6mm到,原裝散熱兩邊有7mm,小小頂.風扇有10mm厚一定放晤落....

作者: hihizaza 時間: 2011-3-22 23:50
try BILTZ shell la,
i use lrp ver2 with heatsink,enough space wor!!!

作者: jf813 時間: 2011-3-23 09:53
回復 6# eyhpoon

I place the ESC on the other side and turn 90degree on my r5. Ya, I think the side link is longer on the crc compare to the R5.....

作者: eyhpoon 時間: 2011-3-23 22:26

回復 eyhpoon

I place the ESC on the other side and turn 90degree on my r5. Ya, I think the sid ...
jf813 發表於 2011-3-23 09:53

登錄/註冊後可看大圖

I have found some 5mm thick heatsink. Order it through web and wait for it to arrive and see if it fits. But certainly cannot mount a fan

作者: jf813 時間: 2011-3-24 09:40
Maybe you can use the heat sink and mount the fan standing up? Seen it done before. not as good as mount it on top but it works.

作者: eyhpoon 時間: 2011-3-24 18:21
I have received the 5mm heatsink (Left), original is on right
Also received some very thin 3M heatsink stickers

登錄/註冊後可看大圖

作者: eyhpoon 時間: 2011-3-24 18:23
Also mount (by double sided tape) the fan in front. Blowing air backwards
I wonder if I need to buy a high rpm one, because it seems like the air flow is not very strong when powered by 1S Lipo

登錄/註冊後可看大圖

作者: eyhpoon 時間: 2011-3-24 18:30
Also painted a pure white "practice shell"

登錄/註冊後可看大圖

The only problem I still have is the small original spur gear (76T). Since this is so small, I need to use a pretty large pinion gear (34T minimum) otherwise motor would hit the rear shaft. I wonder if 76T spur is design for high T motors?
Right now the rollout is close to 67mm which I guess (I am newbie, just learn from forum) is too high for 4.5T motor. Plan to change it to 96T sometime, but I need to wait for it to arrive.

作者: mikuro 時間: 2011-3-24 19:13
本帖最後由 mikuro 於 2011-3-24 21:55 編輯

Also painted a pure white "practice shell"

The only problem I still have is the small origina ...
eyhpoon 發表於 2011-3-24 18:30

登錄/註冊後可看大圖

Hello, for your reference, mine using 24/96 (64 pitch) with 4.0T.
Are you waiting for CRC spur? Actually, you can try other brand instead of waiting for CRC.

作者: joesheng 時間: 2011-3-24 20:50
Very nice ten two son^_^

作者: eyhpoon 時間: 2011-3-24 22:56

Hello, for your reference, mine using 24/96 (64 pitch) with 4.0T.
Are you waiting for CRC spur? ...
mikuro 發表於 2011-3-24 19:13

登錄/註冊後可看大圖

Thanks and I have ordered Kawada and also CRC (Kimbrough) 96T. Cause I live in Beijing and most things need to be bought through mail. So I need to be a little patient.

BTW, CRC now has two versions of spur gear. Originally is made by Kimbrough with 12 1/8 balls. Now they have a version which has 16 3/32 balls. Wonder if anyone has tried?

作者: jf813 時間: 2011-3-25 09:36
回復 16# eyhpoon

yes, I had use the 16 ball spur before. Not really necessary as the diff will not slip much anyway... BTW: The spur came with the kit is for stock racing only, Mod change it to 87-95t la.

作者: eyhpoon 時間: 2011-3-25 14:28

回復 eyhpoon

yes, I had use the 16 ball spur before. Not really necessary as the diff will not ...
jf813 發表於 2011-3-25 09:36

登錄/註冊後可看大圖

Thanks!

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)