RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 鑼絲問題 [打印本頁]

作者: gimsink 時間: 2011-8-8 23:31
標題: 鑼絲問題
請問有冇師兄知道美制鑼絲點睇 ? 例如 4-40 x 1/2 的話, 要用 3/32 六角批去收, 4-40 代表乜 ?另外公制及美制綜絲牙係唔係一樣 ? 我想幫架 RC10T4 換不銹钢鑼絲, 不過唔知道點買相对的美制鑼絲.....

作者: hardmankam 時間: 2011-8-9 01:19
4-40 x 1/2 -> '4' is the screw size, '40' is the thread count per inch, 1/2 is the length in inches.

http://www.engineersedge.com/screw_threads_chart.htm

tips: go to 新填地街, there are a few screw special shops there. just give them the size and they know what to give you. Its better to bring your T4 manual along.

作者: gimsink 時間: 2011-8-14 22:51
前幾日去大照買不銹鋼鑼絲, 一大包3mm 杯頭波頭乜頭物頭買左2百蚊, 可切兩三架車有排用. 可惜冇2.5mm 六角頭鑼絲, 得十字頭. 有冇師兄知道邊间有2.5mm六角頭 ? 另外順便買美制六角鑼絲比T4用, 大照老細問番我轉頭點解今個星期咁多人揾美制六角 ? 話十年冇發市要訂貨等幾日先有, 嘿嘿....另外老細超好人我同佢吹左陣水佢打左個九折比我, 仲有呀四眼師傅幫我汁料, 對完又對怕弄錯, 直得敬佩 ? KWS D 所謂老細真係要誠心誠意學吓咩係待客之道, 否則真係自食其果 !!

作者: rcpop 時間: 2011-8-15 13:34
師兄.. 大照在那裡..我都想買螺絲 ...

作者: gimsink 時間: 2011-8-15 19:33
廣東道九百七十幾號！

作者: rcracing 時間: 2011-8-15 23:50

gimsink 發表於 2011-8-14 22:51

登錄/註冊後可看大圖

前幾日去大照買不銹鋼鑼絲, 一大包3mm 杯頭波頭乜頭物頭買左2百蚊, 可切兩三架車有排用. 可惜冇2.5mm 六角頭 ...

梗好招乎啦,一粒賺你半元

,2百蚊賺你1百蚊去边都好招乎啦..........

作者: gimsink 時間: 2011-8-16 09:06
This is small money, I don't care how much the other peoples earn, as long as I can huy stuffs in a price that acceptable to me that's fine. Many chings said how cheap they can buy stuffs elasewhere but this is no meaning to me, cus I cannot get the so called "cheap price" even I go to the same place.

作者: joesham 時間: 2011-8-16 09:36
Is a good shop, I also by screw there

作者: pma 時間: 2011-8-17 00:28
I also have a T4. If you can buy, please share with me. Thanks.

作者: move7648 時間: 2011-8-17 11:26

gimsink 發表於 2011-8-16 09:06

登錄/註冊後可看大圖

This is small money, I don't care how much the other peoples earn, as long as I can huy stuffs in a ...

同意，自己俾錢俾得開心，價錢自己又覺得ok就得
如果俾錢都要受氣，咁差嗰一百幾十，唔係話大口氣，但我寧願豪俾佢

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)