RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: TAMIYA DB 02 [打印本頁]

作者: sammy 時間: 2011-11-23 20:28
標題: TAMIYA DB 02
TAMIYA DB 02

作者: tiger1 時間: 2011-11-23 20:33
What is the advantage of this design??

作者: 藤原拓海 時間: 2011-11-23 20:33
第1果幅圖好靚...............條女

作者: tiger1 時間: 2011-11-23 20:45
agree

want to see inside too

作者: ryancmlam 時間: 2011-11-23 23:15
Can use stick pack

作者: ftbingobingo 時間: 2011-11-24 03:56

tiger1 發表於 2011-11-23 20:33

登錄/註冊後可看大圖

What is the advantage of this design??

我知!!! 可以用舊款TRANSPONDER

作者: mlee 時間: 2011-11-24 10:28

tiger1 發表於 2011-11-23 20:33

登錄/註冊後可看大圖

What is the advantage of this design??

1)  Tamiya can make some money, tones of options will come....
2)  Players have a new Tamiya buggies to play.
3)  Take away all the belts from DB01

****
Now it can be seen that the center part is not a diff...

作者: tiger1 時間: 2011-11-24 10:29
Center has that extra beveled gear for the stability of the other gears

作者: Wilsonf 時間: 2011-11-24 11:02
new design to cancel all the torque steer in tradition shaft car!

but that involved many bevel gears, seems a low efficiency car...

作者: tiger1 時間: 2011-11-24 16:03
Torque steering is always there with shaft running longitudinally

作者: tiger1 時間: 2011-11-24 16:04
The mid-shaft, on the other hand is not too small. May be high power brushless is a problem....

作者: joho 時間: 2011-11-24 17:01
The major reason I think, is to place the motor like the way you can on a belt drive car, so to eliminate the torqe effect on typical shaft drive car, but at the same time still have all the advantage of a shaft driven car. Whetherit works or not we will have to wait and see.

作者: tiger1 時間: 2011-11-24 17:23
even front and rear shaft runs in different directions, the torque steering situation will still be there, except super high traction.

作者: joho 時間: 2011-11-24 18:56
Torque steer 係同摩打的位置及摩打芯的轉動方向有關，條shaft 咩方向轉只係mo

tor 的作用。

作者: joho 時間: 2011-11-24 19:00
只要個摩打係縱置，就會有torque steer. kyosho 架FS2理論上解決到呢個問題。

作者: tiger1 時間: 2011-11-24 20:11
correct!!

作者: txzmxn 時間: 2011-11-24 21:29
中間嗰個唔係差速來㗎，前後軸同一方向轉，每個bevel牙只接獨其中另一個bevel牙。
個設計都幾突別，不過會唔會無咁㩒用？

作者: RANKS 時間: 2011-11-24 22:40
the numbers of teeth of the bevel gears can be changed just like useing 36 pulley in front and 37 pulley in the back on 501X

作者: Wilsonf 時間: 2011-11-24 23:53
本帖最後由 Wilsonf 於 2011-11-24 23:54 編輯

Here

DB02 from 30:25

and many other good stuff!

作者: ftbingobingo 時間: 2011-11-25 00:55

tiger1 發表於 2011-11-24 16:04

登錄/註冊後可看大圖

The mid-shaft, on the other hand is not too small. May be high power brushless is a problem....

So the demo uses brushed motor

作者: mlee 時間: 2011-11-25 09:53

ftbingobingo 發表於 2011-11-25 00:55

登錄/註冊後可看大圖

So the demo uses brushed motor

The Demo car seems to be the same as DB01 back in the days=> bushed motor setup. However, DB01 can handle bushess system because of its belt drive design. It seems that DB02 is more direct drive and has less room to give, Slipper pad replacement tends to occur more frequently.... Look forwards to review test reports...

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)