There were quite a bit of problem with the 3 珠差設計.
Mugen 'forgot' to design a spring washer in the front/rear diff, adjustment was almost impossible to get right, either too tight or too loose.... and the 設計 basically disallowed any addition of the missing piece...
The middle 珠差 was better by a little bit, also forgot the the spring washer but it can be easily add back to make it very nice and smooth with some good diff lub, e.g. AE lub.作者: tiger1 時間: 2012-3-9 10:19
MIP made an aftermarket front and rear 珠差 for the bulldog, super rare!!!
I have only seen them in brochure and one time on ebay in the last 10+ years!!! They are super smooth, just like most MIP ball diff. 作者: RGear 時間: 2012-3-21 21:17
This car is really hard to find, even can't find in eBay作者: @850 時間: 2012-3-22 17:44
是否近大圍銅鑼灣天橋底沙地,我玩時只有圍圈走及木板跳台.我玩水星及青蛙.作者: tiger1 時間: 2012-3-22 17:56
still can find this car on ebay from time to time.作者: tiger1 時間: 2012-3-22 17:56
yahoo japan has nib from time to time, even today!!作者: jj2006 時間: 2012-4-4 22:35
還有四輪轉向,但大部份都改回頭輪轉向作者: hihizaza 時間: 2012-4-5 11:09
網上有無manual download呢作者: wave 時間: 2012-4-5 11:20
恭喜ching! 我訓過龍,miss 左。。 作者: hihizaza 時間: 2012-4-18 13:27
我部仲等緊零件返,不過點整都無你架咁令立立,正作者: pinky 時間: 2012-5-19 20:44
我細個都有一架.四轉向超正,你係那理Bid回來請pm作者: fat_fat_cat 時間: 2012-5-19 20:50
I get the bulldog in my japan trip when it first release. I still remember I get it when it just reach the distributor, I pack it there, but missed the black main frame:Q:Q 作者: tiger1 時間: 2012-5-20 12:07
4wds 行到直線已經係奇蹟作者: Q太郎 時間: 2012-5-21 20:18
當年我就係用834B砌低佢..代我出一口氣....係我恩車也是我至愛....作者: POLO-GTI 時間: 2012-5-22 01:45
大圍銅鑼灣橋低 :)作者: ting2 時間: 2012-5-24 17:25 本帖最後由 ting2 於 2012-5-24 17:29 編輯
唔玩喇。。。
次次買完都話玩,整好整乾淨就硬係唔捨得玩...
CHING, 知唔知有咩方法可以漂白D鈴呀? 好黃。。。作者: tiger1 時間: 2012-5-24 23:32
use household bleach, not too long though, may be 1/2 hour. 作者: PKKC 時間: 2012-5-25 00:18 回復 ting2 的帖子
Very nice bulldog. I want to get one too!作者: ting2 時間: 2012-5-25 01:04