RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 新玩具 [打印本頁]

作者: ice1234 時間: 2006-11-14 22:51
標題: 新玩具
80% 完成

[ 本帖最後由 ice1234 於 2006-11-14 22:53 編輯 ]

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

作者: gibson 時間: 2006-11-14 23:07
very good, may I ask how to make turns????

作者: 中遠 時間: 2006-11-15 02:08
打仗今既款。。。

作者: BOBBY 時間: 2006-11-18 00:23
几银啊？系边买架？

作者: 中遠 時間: 2006-11-18 00:27
雙星野，千幾好似。。。

作者: KMB182 時間: 2006-11-18 00:38

原帖由中遠於 2006-11-18 00:27 發表
雙星野，千幾好似。。。

呢部車唔多似係星星出..

作者: BOBBY 時間: 2006-11-18 00:49
千幾？1/16架？雙星野好似无甘平啊？

作者: 中遠 時間: 2006-11-18 00:58
以為係星星既泰格。。。

作者: BOBBY 時間: 2006-11-18 01:41
甘系边有买啊？

作者: 中遠 時間: 2006-11-18 02:30
出廣華街問問d模型店店長。。。

作者: Ang 時間: 2006-11-20 18:21
標題: Question
Looks like there are two 130 size motors and there is an integrated receiver + ESC unit. Just curious how does the receiver+ESC control each motor ?

Pls share.

作者: ice1234 時間: 2006-11-21 22:08
use servo to push the switch, so when one motor move , other one remain stop............tank will turn to the direction that u want..

作者: Ang 時間: 2006-11-22 00:54

原帖由 ice1234 於 2006-11-21 22:08 發表
use servo to push the switch, so when one motor move , other one remain stop............tank will turn to the direction that u want..

How does the wiring look like ?

I've got a few motorized model tanks at home and it'd be nice if it's easy to put R/C unit inside.

作者: python 時間: 2006-11-24 09:36
I think like this.

[ 本帖最後由 python 於 2006-11-24 12:07 編輯 ]

: 登錄/註冊後可看大圖

作者: Ang 時間: 2006-11-24 23:14
標題: More pix on the servo-switch setup please
Thanks for the diagram, very interesting.

Any chance to post a close up of the servo-switch setup ?

作者: tiger1 時間: 2006-11-26 14:27
That is a Nichimo 1/35 Tiger 1. It uses two RE140 motors. Not good. The gears are very soft, easily stripped.....

作者: ice1234 時間: 2006-11-26 15:34

原帖由 tiger1 於 2006-11-26 02:27 PM 發表
That is a Nichimo 1/35 Tiger 1. It uses two RE140 motors. Not good. The gears are very soft, easily stripped.....

it's type 130......not RE140 motor................

作者: ice1234 時間: 2006-11-26 15:35

: 登錄/註冊後可看大圖

作者: Ang 時間: 2006-11-26 23:58
標題: Close-up pix of the left/right switch mechanism please!
ice1234:

Very innovative mod

I'm surprised that you can fit so many stuff into a 1/35 platform.

I wish I could install the left/right switch mechanism into my motorized plastic model tanks.

Couple qusetions:

What kiind of micro-servo do you install ?
Would you mind to tell me how to DIY that left/right switch ?
Woud you put more close-up pix of the left/right switch mechanism ?
Would you show the inside of the turret ? Isn't it the place where you put the battery ?

Tak Po got a dual motor ESC but it's too expensive for my liking.

Thanks

作者: ice1234 時間: 2006-11-27 21:38

原帖由 Ang 於 2006-11-26 11:58 PM 發表
ice1234:

Very innovative mod I'm surprised that you can fit so many stuff into a 1/35 platform.

I wish I could install the left/right switch mechanism into my motorized plastic model tank ...

photo

o個兩個只不過係普通撞掣.....鴨記有得賣....
用其中兩個接點......com 同 nc......
當其中一個掣比servo撞到,該撞掣會變no....即係open circuit......o個邊個motor就會停低唔轉.....

[ 本帖最後由 ice1234 於 2006-11-27 22:00 編輯 ]

: 登錄/註冊後可看大圖

作者: ice1234 時間: 2006-11-27 21:51

原帖由 Ang 於 2006-11-26 11:58 PM 發表
ice1234:

Very innovative mod I'm surprised that you can fit so many stuff into a 1/35 platform.

I wish I could install the left/right switch mechanism into my motorized plastic model tank ...

servo --- esky....you can use any servo in same size
The battery are not put inside turret , it just under the receiver

[ 本帖最後由 ice1234 於 2006-11-27 21:53 編輯 ]

作者: Ang 時間: 2006-12-1 23:32
Your 1/35 Tiger I seems to have a big platform to put all those electronics stuff inside. I don't think others have as much space as yours.

作者: kenyips 時間: 2007-2-17 08:37
經典之作

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)