RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Traxxas 1/10 大E-Revo 換控及Gear問題 [打印本頁]

作者: DLAM 時間: 2013-3-27 10:01
標題: Traxxas 1/10 大E-Revo 換控及Gear問題
本帖最後由 DLAM 於 2013-3-27 10:08 編輯

想請教師兄們:

Traxxas 1/10 E-Revo 本身用緊2個Servo, 如果想換個4PL控, 但係個Futaba接收得一個 "ch1"位, 點算?

另外如果架大E-Revo用:

ESC+Motor: Tekin RX8 + T8 2650KV (行4S - 14.8V)
Spur Gear: 60 (32pitch)
Pinion Gear: 應該用幾多? (驚太高溫燒ESC)

作者: kay1926 時間: 2013-3-27 10:28
Y CABLE FOR 2個Servo

作者: 965 時間: 2013-3-27 10:54
How come not using the stock mamba monster esc and 2200kv ar?

Tekin is smoother with sensor.... But for monster truck... Mamba 2200kv + 6s (or even 5) is good combination....

作者: DLAM 時間: 2013-3-27 11:31

965 發表於 2013-3-27 10:54
How come not using the stock mamba monster esc and 2200kv ar?

Tekin is smoother with sensor.... Bu ...

My e-revo came with brushed motors, I am trying to convert it to brushless. Mamba Monster is not easy to buy in Hong Kong. I have a used T8 motor 2650kv, just trying to buy a RX8 to fit it.

作者: 680086 時間: 2013-3-27 17:47
師兄
e-revo Brushless #5608L
睇圖係 18 tooth pinion gear ,, 68 tooth spur gear

作者: DLAM 時間: 2013-3-27 19:24
Yes, I know that gear was for the Castle Mamba Monster 2200kv, I am planning to use 2650kv with 60 spur gear.

作者: 965 時間: 2013-3-27 23:05
Cool.... Tekin is a much better system ... But for monster truck, you better go to their 4038 2000kv, and run 6s ... Similar top speed as 2650 with 4s, but more power .... Slightly bit heavier, but ok for truck la...

作者: jackyrc 時間: 2013-3-28 18:59
Futaba 4PL控, ch1 and ch3 可較同步

作者: DLAM 時間: 2013-3-29 16:06

jackyrc 發表於 2013-3-28 18:59
Futaba 4PL控, ch1 and ch3 可較同步

師兄，教下我點Set得唔得？

作者: Htse 時間: 2013-4-15 14:46

DLAM 發表於 2013-3-29 16:06

登錄/註冊後可看大圖

師兄，教下我點Set得唔得？

using a Y-connector is much much much more easier. and 2650kv motor = not a good idea on monster truck. well u should but couple pinion gear and test the temperature on the motor, try 18T and work ur way down to less tooth or up if it's too hot.

作者: DLAM 時間: 2013-4-16 09:54

Htse 發表於 2013-4-15 14:46

登錄/註冊後可看大圖

using a Y-connector is much much much more easier. and 2650kv motor = not a good idea on monster t ...

What is the safe liimit on temperature of a running Tekin T8 motor (2650KV)?

作者: 965 時間: 2013-4-16 11:02
So you hv 2650 motor already? You actually can try to trade to the tekin 2000kv (longer can) or say hobbywing 2000kv

I love to hv the tekin 2650...

Anyway, ~150f is still ok temp gei....

作者: 965 時間: 2013-4-16 11:02
So you hv 2650 motor already? You actually can try to trade to the tekin 2000kv (longer can) or say hobbywing 2000kv

I love to hv the tekin 2650...

Anyway, ~150f is still ok temp gei....

作者: DLAM 時間: 2013-4-16 13:56

965 發表於 2013-4-16 11:02

登錄/註冊後可看大圖

So you hv 2650 motor already? You actually can try to trade to the tekin 2000kv (longer can) or say ...

Yes, if you have the Tekin T8 2250KV, we can trade.........

作者: Htse 時間: 2013-4-18 08:20

DLAM 發表於 2013-4-16 09:54

登錄/註冊後可看大圖

What is the safe liimit on temperature of a running Tekin T8 motor (2650KV)?

if u can touch it for 3 sec it should be fine....

作者: george519 時間: 2014-4-22 11:11
Hi Ching, 我而家係度爬e revo舊文, 想問一下, 有刷e-revo改無刷, 是否只係換摩打齒同大減便可?? 請教我

作者: DLAM 時間: 2014-4-22 11:49

george519 發表於 2014-4-22 11:11
Hi Ching, 我而家係度爬e revo舊文, 想問一下, 有刷e-revo改無刷, 是否只係換摩打齒同大減便可?? 請教我 ...

成份Motor Mount 要換晒!

作者: DLAM 時間: 2014-4-22 11:56

george519 發表於 2014-4-22 11:11
Hi Ching, 我而家係度爬e revo舊文, 想問一下, 有刷e-revo改無刷, 是否只係換摩打齒同大減便可?? 請教我 ...

仲有有刷版原裝行14mm Hex, 呔軨冇乜選擇！

要改埋行17mm Hex好D ，可以行Pro-line 40 series

我其中一部E-Revo就係咁改

作者: george519 時間: 2014-4-22 12:16

DLAM 發表於 2014-4-22 11:49
成份Motor Mount 要換晒!

嘩, 三四佰走唔甩啦

作者: george519 時間: 2014-4-22 12:20
咁成份Motor Mount加改埋行17mm Hex, 大約要几錢呀? 因睇中左架二手有刷, 但想改無刷玩, 睇下化唔化算

作者: DLAM 時間: 2014-4-22 15:14

george519 發表於 2014-4-22 12:20
咁成份Motor Mount加改埋行17mm Hex, 大約要几錢呀? 因睇中左架二手有刷, 但想改無刷玩, 睇下化唔化算 ...

大概$300-$400左右。你睇中果架擺咗好多次上去都係賣唔出因為太貴(當年新車$3XXX)。
除咗motor mount份嘢另外你要加套1/8 truck 用嘅摩打電變再換埋大軨呔，$4000+走唔甩

作者: george519 時間: 2014-4-22 15:17

DLAM 發表於 2014-4-22 15:14
大概$300-$400左右。你睇中果架擺咗好多次上去都係賣唔出因為太貴(當年新車$3XXX)。
除咗motor mount份嘢 ...

係啦, 佢都擺過左1年架喇, 咁真係無數圍, 去訂新車算喇......
有機會一齊玩番轉啦!

作者: DLAM 時間: 2014-4-22 16:25
好！

作者: bigmouthguy 時間: 2014-4-24 01:39
唔洗用Y CABLE 你SET CHANNEL 3去同轉向同步就OK。

17MM hub 唔貴
http://www.rcmart.com/traxxas-5353x-wheel-hubs-p-28025.html

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)