RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: yokom02漂移呔的問題 [打印本頁]

作者: 地獄羊咩仔 時間: 2006-2-8 21:55
標題: yokom02漂移呔的問題
我今日買左02呔,裝左,岩岩試車,部車響我樓下果d花園地甩到好似氣x船咁,個地好似上次party個小型公園場咁嫁,有咩方法攪到佢冇咁甩,我用ta04(但到左停車場d地(光滑的)又好似冇咁甩~,點好

[ 本帖最後由地獄羊咩仔於 2006-2-8 21:57 編輯 ]

作者: hkopium 時間: 2006-2-8 22:40

原帖由 地獄羊咩仔 於 2006-2-8 21:55 發表
我今日買左02呔,裝左,岩岩試車,部車響我樓下果d花園地甩到好似氣x船咁,個地好似上次party個小型公園場咁嫁,有咩方法攪到佢冇咁甩,我用ta04(但到左停車場d地(光滑的)又好似冇咁甩~,點好

用02 呔, camber 要較大. 後輪用 3 度會咬地D, 因為輪邊軟膠會有多D既接觸面.

作者: 地獄羊咩仔 時間: 2006-2-8 22:42
咁頭呢

作者: DC-5 時間: 2006-2-8 23:04
有無頭單..

作者: 地獄羊咩仔 時間: 2006-2-8 23:19
有

作者: Jim 時間: 2006-2-8 23:42
i dont know how to set it too.....

i am using ta04
now my setting is
02 tire
soft damper oil(>50#)
soft front spring,medium rear spring
front and rear stablise bar
front toe in
front and rear positve(not sure,is that called positive) camber

作者: hkopium 時間: 2006-2-9 00:18
My Toe:

  Front
[]===[]
  :    :
  :    :    <--- 由上面望落去
//===\\
Rear

//===\\ <--- 由車尾水平望 (Camber = 3)

[ 本帖最後由 hkopium 於 2006-2-9 00:21 編輯 ]

作者: Jim 時間: 2006-2-9 00:21

原帖由 hkopium 於 2006-2-9 00:18 發表
Front
[]===[]
: :
: :
//===\\
Rear

rear toe in?will it understeering ka???

作者: Edde 時間: 2006-2-9 20:03

原帖由 Jim 於 2006-2-9 00:21 發表

rear toe in?will it understeering ka???

尾 toe in 唔系幫助轉向咩.........

作者: D1仔 時間: 2006-2-10 17:06
我想問點樣度Camber架.......

作者: Jim 時間: 2006-2-11 03:15

原帖由 D1仔 於 2006-2-10 17:06 發表
我想問點樣度Camber架.......

expensive solution - there has a deck with marks and use a special wheel to measure(very thin wheel).
(actually....i dunno how to use it...ask some pros...)
cheap solution - put your car on a flat and balance surface,then use a compass(圓規) ans ruler to measure

作者: mikewu 時間: 2006-2-11 10:55

原帖由 Jim 於 2006-2-11 03:15 發表

expensive solution - there has a deck with marks and use a special wheel to measure(very thin wheel).
(actually....i dunno how to use it...ask some pros...)
cheap solution - put your car on a ...

Get a set of "set car tools"... Topcad has a set of metal ones for 3xx - 4xx dollars. I use Hudy plastic ones..... but it really helps when it comes to setting up a car.........

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)