RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 用緊E-maxx發燒的師兄，請問 [打印本頁]

作者: shoot 時間: 2007-1-24 01:05
標題: 用緊E-maxx發燒的師兄，請問
有冇邊條link可訂full set套装(吾要散件)？又可落番原裝双摩打，
這網業得T-maxx套裝

http://integy.automated-shops.com/cgi-bin/webc.cgi/st_main.html?p_catid=29&page=5&sid=4wSJJh1jZHIU8eH-34107350493.a2

作者: 毒魚 時間: 2007-1-24 01:20
好紅= ="

作者: orange00 時間: 2007-1-24 09:30
This one is only conversion kit. Do u have the original E-MAXX?

作者: RCman 時間: 2007-1-24 09:42
integy無出過full set 比Emaxx的
如果你係想買,有兩個choice
1) 買左呢套，片底板無用算數，其它Emaxx合用的。
2) 另有一套integy係四對arm，shock tower，其它再要的散買。

不過Emaxx的合金chassis integy無出到傢
只可買Gorilla Maxx 改裝chassis，or 買FLM chassis
我朋友用緊Gorilla Maxx
我就買左FLM chassis。

但有一點，係如果你改左甘多alloy parts的話，
原裝兩個550係頂吳順的，
我地都換曬BL玩傢，
當換左BL後，到所有膠萬向都頂吳順，
甘就要換曬全車CVD啦！
即係你大約要比多$10K(吳計部車)至打算改FULL Alloy parts

作者: shoot 時間: 2007-1-24 11:08
Thanks三位師兄
N年前第一代e-maxx玩過，月頭決定買番部，我睇過4個友台，知如換novak套無刷，需90%以上要改，但問題是，我現場睇過一架全改版用無刷，架車好"游"，直路快而飄飄地........吾識講！所以打算用原裝麼打+14粒電玩，ko咗先換電子嘢&cvd
1) 如我訂這套kit，底版用Gorilla或FLM chassis兩者都一樣fit位嗎
2) 你介紹的牌子，是否7075料

作者: jpmontoya2 時間: 2007-1-24 11:18

原帖由 shoot 於 2007-1-24 01:05 發表
有冇邊條link可訂full set套(吾要散件)？又可落番原裝摩打，
這網業得T-maxx套裝
http://integy.automated-shops.co ... ge=5&sid=4wSJJh ...

Um..basically there are no exisiting kit conversion which you can purcahse and play.....

You do at least need the original F/R diff case (with gears)....and the centre gearbox to make everything work

For chassis, it is mostly recommended Gorillamaxx or FLM as these two were used by other guys round the world, it will give the car alot more ridigidity and response compare to the stock one....

作者: jpmontoya2 時間: 2007-1-24 11:22

原帖由 shoot 於 2007-1-24 11:08 發表
Thanks三位師兄
N年前第一代e-maxx玩過，月頭決定買番部，我睇過4個友台，知如換novak套無刷，需90%以上要改，但問題是，我現場睇過一架全改版用無刷，架車好"游"，直路快而飄飄地........吾識講！所以 ...

To use the novak HV Maxx motor, the minimum you will need to modifiy is metal CVD all round (including the onein the centre gearbox)

The car that you have seen with the HV maxx are very likly with the original chassis and plastic arms......it can fly, but any sort of collision at that speed will meant that your car will be KO~~~

So we suggest if you are to go with brushless, you do at least modify the chassis (the gorillamaxx one also lower the CG so the car is better in handling)..and the all round CVD, that should give enough support to the HV for the time being.....

Another upgrade that you must get is the Piggy Bag shocks....these are needs as the Emaxx is quite a heavy truck......the stock damper will not be able to hold off the weight after the upgrade~

Hope it helps~

Also...both the Gorilamaxx and FLM are made from 6061 T6 aluminium....not 7075~

作者: orange00 時間: 2007-1-24 13:25

原帖由 shoot 於 2007-1-24 11:08 發表
Thanks三位師兄
N年前第一代e-maxx玩過，月頭決定買番部，我睇過4個友台，知如換novak套無刷，需90%以上要改，但問題是，我現場睇過一架全改版用無刷，架車好"游"，直路快而飄飄地........吾識講！所以 ...

Hi Shoot,
Your 1st generation E-MAXX is on my bench under modification. The chassis will be FLM. The stock chassis already install at my E-HELLFIRE.
Whatever parts you modify, just no GPx. For such kind of monster truck, the copy metal parts from plastic without any re-design will gain nothing.
By the way, will you concern E-REVO?
With this roller kit, just add a Slipperential (which cost 160 dollars) even can forget the centre gear box. You already have nearly a complet kit.

http://www.rc-monster.com/proddetail.php?prod=RCM_G2R_ROLLER&cat=11

登錄/註冊後可看大圖

[ 本帖最後由 orange00 於 2007-1-24 13:27 編輯 ]

作者: shoot 時間: 2007-1-24 19:54
Thank you你地好好人，我找到Gorilla個主頁了，見到G2 carbon fiber kit幾好, but only 2.5mm厚.....，擔心前面支點個位會易斷(友台師兄架車原裝成架斷開)，orange00兄你介紹套kit我都睇緊，Price好吸引&外形吾錯，but only四支小油壓 work 吾work.......？
其實我只想找一套用料好少少的kit為主(and 有dd design的款)，吾想又買老展貨玩，速度反而要求吾高

http://www.gorillamaxx.com/

作者: orange00 時間: 2007-1-24 22:03

原帖由 shoot 於 2007-1-24 19:54 發表
Thank you你地好好人，我找到Gorilla個主頁了，見到G2 carbon fiber kit幾好, but only 2.5mm厚.....，擔心前面支點個位會易斷(友台師兄架車原裝成架斷開)，orange00兄你介紹套kit我都睇緊，Price好吸引&外形 ...

果四支係原廠俾revo用既油壓. 你話work唔work.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)