RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 沙猪比較容易損壞是邊 PART 呀？ [打印本頁]

作者: mark999hk 時間: 2006-2-14 09:44
標題: 沙猪比較容易損壞是邊 PART 呀？
唉~~嗰日吾係好識用個電撻，不停係咁撻.....終放搞壞咗電撻入面粒單向。而家想換返個手拉好似好啲，一來可以就倒力同吾怕個電撻冇電。

仲有想問吓各師兄，沙猪比較容易損壞是邊 PART 呀？Thanks

[ 本帖最後由天照於 2006-2-14 12:27 編輯 ]

作者: Skyline 時間: 2006-2-14 11:04
Spur gear .... 經常性掃牙 .....

作者: Skyline 時間: 2006-2-14 11:05
狗骨杯，亦經常性打爆 ......

作者: mark999hk 時間: 2006-2-14 11:09

原帖由 Skyline 於 2006-2-14 11:05 AM 發表
狗骨杯，亦經常性打爆 ......

thanks, 頭定尾呀？

作者: mark999hk 時間: 2006-2-14 11:10

原帖由 Skyline 於 2006-2-14 11:04 AM 發表
Spur gear .... 經常性掃牙 .....

sorry, where is it located?

作者: Skyline 時間: 2006-2-14 11:36

原帖由 mark999hk 於 2006-2-14 11:09 發表

thanks, 頭定尾呀？

後輪，另外原庒 break 粒膠六角都好易撻哂

作者: Skyline 時間: 2006-2-14 11:36

原帖由 mark999hk 於 2006-2-14 11:10 發表

sorry, where is it located?

車中間凸咗出嚟好大隻嘅齒輪 ....

作者: mark999hk 時間: 2006-2-14 11:40

原帖由 Skyline 於 2006-2-14 11:36 AM 發表

車中間凸咗出嚟好大隻嘅齒輪 ....

how much of that 大隻嘅齒輪?

作者: Skyline 時間: 2006-2-14 13:37

原帖由 mark999hk 於 2006-2-14 11:40 發表

how much of that 大隻嘅齒輪?

$2X per piece ... don't worry ...

作者: Skyline 時間: 2006-2-14 13:40

原帖由 mark999hk 於 2006-2-14 11:40 發表

how much of that 大隻嘅齒輪?

Oh yes, regarding your roto start and the damaged one-way bearing issue. Is there anything wrong with the engine where U cannot start the engine, even if U keep using the roto start? Since the roto start provides a very powerful turning force, it can damage the engine if keep pressing the one button for a long time.

作者: mark999hk 時間: 2006-2-14 13:45

原帖由 Skyline 於 2006-2-14 01:40 PM 發表

Oh yes, regarding your roto start and the damaged one-way bearing issue. Is there anything wrong with the engine where U cannot start the engine, even if U keep using the roto start? Since ...

Thanks for opinion. So, I will change the hand start for the savage. It will be easy for me to use.

作者: Skyline 時間: 2006-2-14 14:17

原帖由 mark999hk 於 2006-2-14 13:45 發表

Thanks for opinion. So, I will change the hand start for the savage. It will be easy for me to use.

That's up to U la brother, but remember not to pull too hard when starting, cause I've broke many pull start before ...

作者: rickyl215 時間: 2006-2-14 16:16

原帖由 mark999hk 於 2006-2-14 09:44 發表
唉~~嗰日吾係好識用個電撻，不停係咁撻.....終放搞壞咗電撻入面粒單向。而家想換返個手拉好似好啲，一來可以就倒力同吾怕個電撻冇電。

仲有想問吓各師兄，沙猪比較容易損壞是邊 ...

副計末run in好最好都唔好用電撻住！因壓力仲係比較大,買個粒one way用住手拉先啦師兄。

作者: mark999hk 時間: 2006-2-14 16:18

原帖由 rickyl215 於 2006-2-14 04:16 PM 發表

副計末run in好最好都唔好用電撻住！因壓力仲係比較大,買個粒one way用住手拉先啦師兄。

Not run in yet~~~sorry, do I know you?

作者: mark999hk 時間: 2006-2-14 16:44

原帖由 Skyline 於 2006-2-14 02:17 PM 發表

That's up to U la brother, but remember not to pull too hard when starting, cause I've broke many pull start before ...

Mr. Skyline, do you have Savage X?

作者: rickyl215 時間: 2006-2-14 16:48
因副計只run in咗1L油左右,所以未完全run in好架！

作者: mark999hk 時間: 2006-2-14 16:50

原帖由 rickyl215 於 2006-2-14 04:48 PM 發表
因副計只run in咗1L油左右,所以未完全run in好架！

Oh~~you are the guy who sell the Savage to me~~?

作者: rickyl215 時間: 2006-2-14 16:53
因副机係我帮佢run架！

作者: mark999hk 時間: 2006-2-14 16:55

原帖由 rickyl215 於 2006-2-14 04:53 PM 發表
因副机係我帮佢run架！

ok~~but how many "L" need to run in of this 25 class engine ka? Thanks

作者: rickyl215 時間: 2006-2-14 17:02
大约3L左右,當然最正確要感覺下 sleeve同 piston仲緊唔緊.(已上只作參考)

作者: Skyline 時間: 2006-2-14 17:25

原帖由 mark999hk 於 2006-2-14 16:44 發表

Mr. Skyline, do you have Savage X?

Not yet brother, haven't seen in HK and is only available via U.S. websites that ship goods worldwide .... price is not bad at all ...

作者: mark999hk 時間: 2006-2-16 10:43
標題: Parts
大鑊~~昨天走出 KWS 找粒手拉/電撻的單向 Bearing，週街都冇貨。部沙猪又要 wait 才可以玩~~真係"頂"吖

作者: Skyline 時間: 2006-2-16 14:13

原帖由 mark999hk 於 2006-2-16 10:43 發表
大鑊~~昨天走出 KWS 找粒手拉/電撻的單向 Bearing，週街都冇貨。部沙猪又要 wait 才可以玩~~真係"頂"吖

快摺有冇現貨？

作者: mark999hk 時間: 2006-2-16 14:17

原帖由 Skyline 於 2006-2-16 02:13 PM 發表

快摺有冇現貨？

Only have 手拉$185-$190 instock, but no 單向 Bearing

作者: WTO 時間: 2006-2-16 15:48

原帖由 mark999hk 於 2006-2-16 14:17 發表

Only have 手拉$185-$190 instock, but no 單向 Bearing

Buy from interent la.
http://www2.towerhobbies.com/cgi ... mp;I=LXDLN7&P=7

作者: mark999hk 時間: 2006-2-16 15:59

原帖由 WTO 於 2006-2-16 03:48 PM 發表

Buy from interent la.
http://www2.towerhobbies.com/cgi ... XDLN7&

Thanks, Mr. WTO. I just got a 100% new 25class hand start and the oneway bearing this afternoon by 2nd hand. It is only 200 for whole set. But anyway, thx alot

作者: moki 時間: 2006-2-16 20:32
Wai brother Mark, you see what I made!!??

作者: mark999hk 時間: 2006-2-16 21:37

原帖由 moki 於 2006-2-16 08:32 PM 發表
Wai brother Mark, you see what I made!!??

You carzy guy

. But I love it~~

作者: mark999hk 時間: 2006-2-20 15:01
標題: R U N - I N
各位師兄，小弟有小小嘢請教。就是如果我 Run-in 我部沙猪 25 級 Engine (部沙猪放在地上不動的時候)，部機的理想温度是多少呀？及放在地上慢慢行的理想温度又是多少？當 Run - in 完成，它的機温的可以去到幾多而又不會 Over Heat 呢？謝謝

作者: WTO 時間: 2006-2-20 15:59
always keep it below 120c when after high speed running.

作者: mark999hk 時間: 2006-2-20 16:02

原帖由 WTO 於 2006-2-20 03:59 PM 發表
always keep it below 120c when after high speed running.

But how much for run-in ar? thanks

作者: WTO 時間: 2006-2-20 16:06

原帖由 mark999hk 於 2006-2-20 16:02 發表

But how much for run-in ar? thanks

not exceed 100c

作者: mark999hk 時間: 2006-2-20 16:08

原帖由 WTO 於 2006-2-20 04:06 PM 發表

not exceed 100c

Thanks fo your reply.

作者: rickyl215 時間: 2006-2-20 16:22
我之前果架就 idle 70-80℃ 幔走 90-100℃ 極速110-120℃,副机過120℃就開始立机,
過140℃就overheat！

作者: mark999hk 時間: 2006-2-21 11:14

原帖由 rickyl215 於 2006-2-20 04:22 PM 發表
我之前果架就 idle 70-80℃ 幔走 90-100℃ 極速110-120℃,副机過120℃就開始立机,
過140℃就overheat！

but the 25 class engine is very easy to go to 90℃-100℃ if I put on the floor (no running) when I run-in the engine. why gei?

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)