RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Keep motor fast? [打印本頁]

作者: billy86che 時間: 2007-11-13 13:44
標題: Keep motor fast?
Why don't we talk about how to keep a motor fast?

作者: scalpel 時間: 2007-11-13 15:23

原帖由 billy86che 於 2007-11-13 13:44 發表

 登錄/註冊後可看大圖

Why don't we talk about how to keep a motor fast?

Do you have any suggestion? I want to know too!

作者: sumandy 時間: 2007-11-13 15:38
老師. 你真係要教下我

作者: billy86che 時間: 2007-11-13 16:59
I'll at least do these:

1. reshim the rotor so it rotates at(near) the centre of the magnetic field.
2. check if the rotor runs smoothly on the 2 bearings.
3. balance the rotor.
4. run-in the motor at a low voltage.
5. check its temperature after a few laps.

any other suggestions?

[ 本帖最後由 billy86che 於 2007-11-13 17:40 編輯 ]

作者: terencelyl7411 時間: 2007-11-13 18:25
fly copper head if that is black
spary motor cleaner after play
see the motor bearing is fit or not when brand new

作者: billy86che 時間: 2007-11-13 20:35

原帖由 terencelyl7411 於 2007-11-13 18:25 發表

 登錄/註冊後可看大圖

fly copper head if that is black
spary motor cleaner after play
see the motor bearing is fit or not when brand new

But would it be too difficult to use a standard commutator lathe on a mini-z motor?

作者: terencelyl7411 時間: 2007-11-13 20:59
you're talking about if the motor case not sit with bearing/rotor ?
usually , i would not lathe the motor case , cause it may not refined as the
machine/ computer cutting , so i will test before i buy ( not all the shop can give me this service !

)
but normally , it's ok ! . for me , if the motor case not good fit , i'll just use an old one or replace the
bearing the see if it will better or not .

[ 本帖最後由 terencelyl7411 於 2007-11-13 21:02 編輯 ]

作者: billy86che 時間: 2007-11-13 21:04
" lathe the motor case "???
Here is a comm lathe. How can it cut the motor case?

[ 本帖最後由 billy86che 於 2007-11-13 21:08 編輯 ]

作者: sumandy 時間: 2007-11-13 21:39
如果用手繞芯. 用邊隻Motor Case好呢?

作者: billy86che 時間: 2007-11-13 21:51

原帖由 sumandy 於 2007-11-13 21:39 發表

 登錄/註冊後可看大圖

如果用手繞芯. 用邊隻Motor Case好呢?

其實用邊隻Motor Case(PN or ATM)都可以好快, 不過可能要調較一吓麼打芯前方個銅圈嘅位置.

[ 本帖最後由 billy86che 於 2007-11-13 21:54 編輯 ]

作者: terencelyl7411 時間: 2007-11-13 22:43

原帖由 billy86che 於 2007-11-13 09:04 PM 發表 <a href="http://bbs.rc-evo.com/redirect.php?goto=findpost&pid=638755&ptid=62000" target="_blank"><img src="http://bbs.rc-evo.com/images/common/back.gif" border="0" alt="" /></a> 
" lathe the motor case "??? 
Here is a comm lathe. How can it cut the motor case?<img src="images/smilies/default/shocked.gif" smilieid="6" border="0" alt="" />

oic , i dont know what's that word , we call this as copper head meachine

作者: terencelyl7411 時間: 2007-11-13 22:44

原帖由 billy86che 於 2007-11-13 09:51 PM 發表 <a href="http://bbs.rc-evo.com/redirect.php?goto=findpost&pid=638809&ptid=62000" target="_blank"><img src="http://bbs.rc-evo.com/images/common/back.gif" border="0" alt="" /></a> 

 

 
其實用邊隻Motor Case(PN or ATM)都可以好快, 不過可能要調較一吓麼打芯前方個銅圈嘅位置.

i prefer the new atm one , new endball seems smarter

作者: billy86che 時間: 2007-11-13 23:23

原帖由 terencelyl7411 於 2007-11-13 22:43 發表

 登錄/註冊後可看大圖

oic , i dont know what's that word , we call this as copper head meachine

Yes, we call it "銅頭機" in cantonese but in English, it is "Commutator Lathe".
Please, if you have used that kind of machine on a 130 motor, show us how. I guess many people here want to see that.

作者: sumandy 時間: 2007-11-14 00:18

原帖由 terencelyl7411 於 2007-11-13 22:44 發表

 登錄/註冊後可看大圖

i prefer the new atm one , new endball seems smarter

New ATM? like Stock R or AD stock type?

作者: terencelyl7411 時間: 2007-11-14 10:24
M1 Endbell , dont know , it should be the stock R one

作者: terencelyl7411 時間: 2007-11-14 10:24

原帖由 billy86che 於 2007-11-13 11:23 PM 發表 <a href="http://bbs.rc-evo.com/redirect.php?goto=findpost&pid=638957&ptid=62000" target="_blank"><img src="http://bbs.rc-evo.com/images/common/back.gif" border="0" alt="" /></a> 

 

 
Yes, we call it "銅頭機" in cantonese but in English, it is "Commutator Lathe". 
Please, if you have used that kind of machine on a 130 motor, show us how. I guess many people here want to see tha ...

i dont have that , but some brother fly copper head for me , i dont know what he use

作者: billy86che 時間: 2007-11-14 11:42

原帖由 terencelyl7411 於 2007-11-14 10:24 發表

 登錄/註冊後可看大圖

i dont have that , but some brother fly copper head for me , i dont know what he use

Ask him to post that, please!

作者: terencelyl7411 時間: 2007-11-14 17:09
just ask Gibson sir ...

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)