RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 有冇刨殼技術分享? [打印本頁]

作者: billy86che 時間: 2007-11-14 15:53
標題: 有冇刨殼技術分享?
有冇刨殼技術分享?
要薄又唔穿.please.

作者: henry888 時間: 2007-11-14 16:17
haha老師, 你都要做幾多準備wor

作者: kennily 時間: 2007-11-14 16:17
我的經驗就是一邊刨一邊睇清楚....一有過龍就補返d筆地再刨 (個人經驗分享,不一定最好)

作者: penny. 時間: 2007-11-14 17:15
講到到樣野，一定係搵Henry啦！

作者: checkie 時間: 2007-11-14 21:18
羅記~~~~~~~~~~~~~~~~~~~~~~~~~~

作者: henry888 時間: 2007-11-15 00:05
羅到唔想羅喇, 好辛苦
羅得快又穿, 羅得慢又累
隻手痺哂嫁

作者: billy86che 時間: 2007-11-15 07:23
講吓用咩工具呀?

作者: henry888 時間: 2007-11-15 10:22
鴨記$25蚊一個既羅頭(鑽石波羅頭)個表面有好多刀片仔咁既
有好多款, 買隻蛋形, 個頭有少少平既就會好刨d, 就手d

作者: 800mah 時間: 2007-11-16 01:56
乜野叫' 刨殼' ??

作者: henry888 時間: 2007-11-16 03:03

原帖由 800mah 於 2007-11-16 01:56 發表

 登錄/註冊後可看大圖

乜野叫' 刨殼' ??

rub off the extra plastic from the body to make it lighter than b4, the CG lower than b4 ,
improve acceleration and the reaction in the corner

作者: 800mah 時間: 2007-11-17 19:53
i see, then maybe the next thing kyosho should do is to produce some 'light weight' mini-z bodies just like what tamiya does with polycarbonates.

作者: billy86che 時間: 2007-11-17 21:47

原帖由 800mah 於 2007-11-17 19:53 發表

 登錄/註冊後可看大圖

i see, then maybe the next thing kyosho should do is to produce some 'light weight' mini-z bodies just like what tamiya does with polycarbonates.

I don't think the Japanese will understand our demand.
Also, producing lighter body shell by making the plastics thinner is a lot more expensive. It is not the same case as using polycarbonates.

作者: henry888 時間: 2007-11-18 01:49

原帖由 800mah 於 2007-11-17 19:53 發表

 登錄/註冊後可看大圖

i see, then maybe the next thing kyosho should do is to produce some 'light weight' mini-z bodies just like what tamiya does with polycarbonates.

好似我地咁玩係kyosho既客路屬小部份
4wd主打drift, 只係我地玩到佢咁盡
睇番人地外國玩車仔, 主要都係玩下樣, 有基本性能, 絕少DIY創作

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)