RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: RC10 Refurbishment [打印本頁]

作者: ryancmlam 時間: 2007-12-21 22:53
標題: RC10 Refurbishment
After seeing Bro Frankie played his vintage RC10 at TKO, I bid it from ebay. The shell is so ugly and needs to be refurbished.

作者: eddywon 時間: 2007-12-21 23:15
用迫力油？係咪有毒o架？你毒發未呀？

講笑！我都有要番新車殼，正猶疑用模型天拿水定點！！

作者: recargo 時間: 2007-12-21 23:37
I share your happiness.

作者: agentjerry 時間: 2007-12-22 11:01

原帖由 ryancmlam 於 2007-12-21 22:53 發表

 登錄/註冊後可看大圖

After seeing Bro Frankie played his vintage RC10 at TKO, I bid it from ebay. The shell is so ugly and needs to be refurbished.

Ryan Hing,

What material u used to wash away the old color?

tks

作者: ryancmlam 時間: 2007-12-23 01:06
Jerry Hing,

As you can see from the picture, I used the brake fuild ($41, 0.5L from Caltex). It is water soluble so that you can use water to remove the residual brake fuild form the body. I used around 0.25L to remove all the paint out. You can do it by just soaking the brake fuild into a unused colth or "fish tank filter cotton" and put on the paint for 15-20min, then use unused colth to rub the paint out. Of couse, you have to use Mr. Thinner to remove the residual color.

Ryan

作者: minimini 時間: 2007-12-23 03:01
hi bro ryan............. your car is really lovely ..........

but............the servo saver is not the original wor........

作者: ryancmlam 時間: 2007-12-23 09:03

原帖由 minimini 於 2007-12-23 03:01 發表

 登錄/註冊後可看大圖

hi bro ryan............. your car is really lovely ..........

but............the servo saver is not the original wor........

Bro minimini, your eyes are so 'sharp'.

Yes, the servo saver is not the original because we (Frankie and I) didn't regonised from the photos when placed the bid at ebay. Bro Frankie had helped me to bid the original servo saver from ebay again. The servo saver that you saw in the photos is modified from Futaba servo horns.

作者: minimini 時間: 2007-12-23 23:47
the gear box is the 6-gear tranny or stealth one ??........

作者: lastenfield 時間: 2007-12-24 00:54

原帖由 minimini 於 2007-12-23 23:47 發表

 登錄/註冊後可看大圖

the gear box is the 6-gear tranny or stealth one ??........

See see the gear box holding scews from the bottom pic!

作者: minimini 時間: 2007-12-24 00:57

原帖由 lastenfield 於 2007-12-24 00:54 發表

 登錄/註冊後可看大圖

See see the gear box holding scews from the bottom pic!

oic.......using small screws......should be stealth.......

作者: ryancmlam 時間: 2007-12-24 15:56

原帖由 minimini 於 2007-12-24 00:57 發表

 登錄/註冊後可看大圖

oic.......using small screws......should be stealth.......

Yes. This one is stealth gear box. I bid another one with 6 gear box which is on the way to Hong Kong.

BTW, I am looking for the motor pinion gear for the 6 six gear box. Do you know where I can find it or what pitch it should be ? Can I use the Tamiya one ?

作者: go2usie 時間: 2007-12-24 17:45
Bro Ryan ~

Your RC10 looks cool can classic~
Do u think it will be ready for a race on next week~
if so, i will try to fix my T losi and hop of i can have a race with yours ~

作者: ryancmlam 時間: 2007-12-24 23:56

原帖由 go2usie 於 2007-12-24 17:45 發表

 登錄/註冊後可看大圖

Bro Ryan ~

Your RC10 looks cool can classic~
Do u think it will be ready for a race on next week~
if so, i will try to fix my T losi and hop of i can have a race with yours ~

I think so. Will let you know after this X'mas holiday.

作者: minimini 時間: 2007-12-25 02:22

原帖由 ryancmlam 於 2007-12-24 15:56 發表

 登錄/註冊後可看大圖

Yes. This one is stealth gear box. I bid another one with 6 gear box which is on the way to Hong Kong.

BTW, I am looking for the motor pinion gear for the 6 six gear box. Do you know where I c ...

I think the pinion gear should be 32 pitch.........

作者: ryancmlam 時間: 2007-12-25 08:52

原帖由 minimini 於 2007-12-25 02:22 發表

 登錄/註冊後可看大圖

I think the pinion gear should be 32 pitch.........

Thanks Bro minimini. BTW, I was given to know from Frankie that you have a lot of vintage rc car. Mr. Mikewu will, sometimes, call for a Vintage offroad party at TKO. Do you want to join ?

作者: minimini 時間: 2007-12-25 11:53

原帖由 ryancmlam 於 2007-12-25 08:52 發表

 登錄/註冊後可看大圖

Thanks Bro minimini. BTW, I was given to know from Frankie that you have a lot of vintage rc car. Mr. Mikewu will, sometimes, call for a Vintage offroad party at TKO. Do you want to join ?

absolutely yes........actually I am going to build up a RC10 for hard-running...........hope to join you guys in TKO soon.........

作者: ryancmlam 時間: 2007-12-25 18:58
That's go. Let our RC10s race togather at TKO

作者: lastenfield 時間: 2007-12-25 22:23

原帖由 minimini 於 2007-12-25 11:53 發表

 登錄/註冊後可看大圖

absolutely yes........actually I am going to build up a RC10 for hard-running...........hope to join you guys in TKO soon.........

Could I join your function?

作者: minimini 時間: 2007-12-25 22:38

原帖由 lastenfield 於 2007-12-25 22:23 發表

 登錄/註冊後可看大圖

Could I join your function?

why not ??!!.......come on baby.......

作者: ryancmlam 時間: 2007-12-25 22:49

原帖由 lastenfield 於 2007-12-25 22:23 發表

 登錄/註冊後可看大圖

Could I join your function?

Yes, pls check "party section" and I will also PM your guys when the "Vintage Offroad party is held"

作者: lastenfield 時間: 2007-12-25 23:28

原帖由 ryancmlam 於 2007-12-25 22:49 發表

 登錄/註冊後可看大圖

Yes, pls check "party section" and I will also PM your guys when the "Vintage Offroad party is held"

Thank you very much!

作者: go2usie 時間: 2007-12-26 18:34
ryan . will u put put on a set of new "shoes" or which its came with ?

作者: tiger1 時間: 2007-12-26 18:40
I wish I could join la....

作者: go2usie 時間: 2007-12-26 19:04
dont think just do~~~ dont think just join~~~

作者: go2usie 時間: 2007-12-26 19:04
bro ryan~ does your RC10 have a rear wing ?

作者: ryancmlam 時間: 2007-12-26 22:24
Bro go2usie.

1. Shoes: No time to buy the new "shoes" and I think I will use the original one first and then buy new. (in fact, I don't know which sets of shoes are appropriate, need to ask Bro Frankie).

2. Rear Wing, the re-release one is one its way to my home. However, as I can't wait for it, I put the 3 racing plastic one as the temporary wing (see attached photos). Hoping it looks not so ugly.

[ 本帖最後由 ryancmlam 於 2007-12-26 23:59 編輯 ]

作者: minimini 時間: 2007-12-27 09:57

原帖由 ryancmlam 於 2007-12-26 22:24 發表

 登錄/註冊後可看大圖

Bro go2usie.

1. Shoes: No time to buy the new "shoes" and I think I will use the original one first and then buy new. (in fact, I don't know which sets of shoes are appropriate, need to ask Bro Fra ...

the plastic wing looks a bit too wide wor.........but at least it can have some protection when "cup 4".......

I will buy one too......

作者: ryancmlam 時間: 2007-12-27 13:28
RC10 Lovers, pls note and join if you have time

http://bbs.rc-evo.com/viewthread ... &extra=page%3D1

作者: go2usie 時間: 2007-12-27 16:33
this will be my TKO 30 racer.....

作者: go2usie 時間: 2007-12-27 16:33
Team Losi Jrx2 Pro

作者: go2usie 時間: 2007-12-27 16:34
with Novak T4 .... matched era~

作者: minimini 時間: 2007-12-27 18:40

原帖由 go2usie 於 2007-12-27 16:33 發表

 登錄/註冊後可看大圖

Team Losi Jrx2 Pro

wa....... "Losi 5-link"........very lovely !!........

作者: go2usie 時間: 2007-12-27 19:32
the 5-link design is special.

actually, i have not much of this buggy i can find.

作者: go2usie 時間: 2007-12-27 19:38
and , bro minimini, do u have any information about this motor ?

<< cant uplod pic -- over limit per day >>

this motor is Trinity - "monster horsepower - 85-87 world championship " wrote over the motor.

作者: li5115 時間: 2007-12-27 23:34
換然一新。恭喜！恭喜！

作者: tiger1 時間: 2007-12-27 23:50
very nice lah

作者: tiger1 時間: 2007-12-27 23:51
JRX Pro by far was the best Losi buggy, I think better than xx4 or xxx4.

作者: minimini 時間: 2007-12-27 23:58

原帖由 go2usie 於 2007-12-27 19:38 發表

 登錄/註冊後可看大圖

and , bro minimini, do u have any information about this motor ?

>

this motor is Trinity - "monster horsepower - 85-87 world championship " wrote over the motor.

the motor sticker is transparent with black words ..........or pink sticker with black words ??........I think I may have them......

作者: go2usie 時間: 2007-12-28 01:11
it is pink sticker with black letters printed over.

作者: go2usie 時間: 2007-12-28 01:12
標題: 回復 33# 的帖子
i mean i have not much information i can find...

i wanna find more about the jrx2

作者: minimini 時間: 2007-12-28 01:12

原帖由 go2usie 於 2007-12-28 01:11 發表

 登錄/註冊後可看大圖

it is pink sticker with black letters printed over.

oic...... I got it too......

作者: go2usie 時間: 2007-12-28 01:21
do u have its diagram ....or manual or else ?

there are no marking with the angle of the bell ... after apart and clean ... it run not smooth....

作者: go2usie 時間: 2007-12-28 16:35
pic upload

作者: ryancmlam 時間: 2008-1-1 01:24
Bro Frankie,
I found that we can use the tamiya DT02 parts to modify the RC10 so that it can use the 2.2" tryes or tamiya tryes.

1. Front wheels: Replace the RC10 uprights by DT02 or TA01/02's one. Need to add spacers. Part no.0555059, JPY420

2. Rear wheels: Replace the axle hub by DF02's one. Need to make the button hold a bit large and file out the button a bit.

[ 本帖最後由 ryancmlam 於 2008-1-1 01:55 編輯 ]

作者: minimini 時間: 2008-1-1 01:41

原帖由 ryancmlam 於 2008-1-1 01:24 發表

 登錄/註冊後可看大圖

Bro Frankie,
I found that we can use the tamiya DT02 parts to modify the RC10 so that it can use the 2.2" tryes or tamiya tryes.

1. Front wheels: Replace the RC10 uprights by DT02's one. Need to a ...

Hi bro Ryan & Frankie,

just a wise guess only.......is it possible to use the Kyosho RB5 steering parts for replacement ??........coz' I trust Kyosho' plastic material more than Tamiya......

作者: ryancmlam 時間: 2008-1-1 01:55

原帖由 minimini 於 2008-1-1 01:41 發表

 登錄/註冊後可看大圖

Hi bro Ryan & Frankie,

just a wise guess only.......is it possible to use the Kyosho RB5 steering parts for replacement ??........coz' I trust Kyosho' plastic material more than Tamiya......

No idea on whether Kyosho RB5 parts can be used. I tried Tamiya DT02 only because I have it. The performance of my vintage RC10 is excellent, definitely out of my expectation, it is better than the new Tamiya DT02. An 1980's RC10 is better than a 2000's DT02.

作者: minimini 時間: 2008-1-1 02:02

原帖由 ryancmlam 於 2008-1-1 01:55 發表

 登錄/註冊後可看大圖

No idea on whether Kyosho RB5 parts can be used. I tried Tamiya DT02 only because I have it. The performance of my vintage RC10 is excellent, definitely out of my expectation, it is better than th ...

寶刀未老.........

作者: minimini 時間: 2008-1-1 02:13

原帖由 ryancmlam 於 2008-1-1 01:55 發表

 登錄/註冊後可看大圖

No idea on whether Kyosho RB5 parts can be used. I tried Tamiya DT02 only because I have it. The performance of my vintage RC10 is excellent, definitely out of my expectation, it is better than th ...

I think RC10 with metal bath-tub chassis got better performance than the graphite one......coz' it has a better weight balance.....pls correct me if I am wrong.......

作者: ryancmlam 時間: 2008-1-1 02:26

原帖由 minimini 於 2008-1-1 02:13 發表

 登錄/註冊後可看大圖

I think RC10 with metal bath-tub chassis got better performance than the graphite one......coz' it has a better weight balance.....pls correct me if I am wrong.......

I suppose "the graphite one" that you mean is the graphite version Vintage RC10, not the B4. I don't have idea on which one is better. I like the RC10 gold pan only because it was my dream car when I was a kid.

作者: minimini 時間: 2008-1-1 02:29

原帖由 ryancmlam 於 2008-1-1 02:26 發表

 登錄/註冊後可看大圖

I suppose "the graphite one" that you mean is the graphite version Vintage RC10, not the B4. I don't have idea on which one is better. I like the RC10 gold pan only because it was my dream car whe ...

yes....... I do love the gold pan......

but I only got the black one now.......plan to use it for hard-running soon......

BTW, any suggestions about the motor & gear ratio ??..... Thx !!

作者: ryancmlam 時間: 2008-1-1 02:47

原帖由 minimini 於 2008-1-1 02:29 發表

 登錄/註冊後可看大圖

yes....... I do love the gold pan......

but I only got the black one now.......plan to use it for hard-running soon......

BTW, any suggestions about the motor & gear ratio ??..... Thx !!

My hard-running RC10 uses black pig. I tried pinion 26T with a spur 81T (stealth 48 ptich gear case) and found that the motor was very hot. Bro Frankie said that the correct pinion gear should be from 18 to 22T. I then checked the manual and noted that the gear ratio of the stealth gear case is 2.25. So, the gear ratio that I used was 81/26 x 2.25 = 7. That was why it was very hot.

Overall gear ratio of
Pinion 18T = 10.125
Pinion 22T = 8.28

I think a gear ratio of around 8 to 10 is very reasonable for a 2WD buggy.

[ 本帖最後由 ryancmlam 於 2008-1-1 02:54 編輯 ]

作者: tiger1 時間: 2008-1-1 08:02

原帖由 ryancmlam 於 2008-1-1 01:55 發表

 登錄/註冊後可看大圖

No idea on whether Kyosho RB5 parts can be used. I tried Tamiya DT02 only because I have it. The performance of my vintage RC10 is excellent, definitely out of my expectation, it is better than th ...

I have the MIP 4wd RC10, which was like a dream to drive, I have also tried 2wd rc10 but even in 2wd, rc10 is very pleasant to drive, almost as good as a modern day touring car in 4wd

except 2wd rc10 cannot drift.

BUT, BUT, but I have seen Masami drifted a rc10b3 in one of the world championship ....

作者: ryancmlam 時間: 2008-1-1 09:45

原帖由 tiger1 於 2008-1-1 08:02 發表

 登錄/註冊後可看大圖

I have the MIP 4wd RC10, which was like a dream to drive, I have also tried 2wd rc10 but even in 2wd, rc10 is very pleasant to drive, almost as good as a modern day touring car in 4wd except ...

Do you mind to show us the picture of your MIP 4WD RC10 ?

作者: minimini 時間: 2008-1-1 14:13
I think there are several different versions of MIP 4WD RC10 .........with chain drive ........& belt drive too.......

here is the one in IFMAR 1987' World Championship.......

photo from http://www.geocities.jp/giequip/RC.TOP.html

[ 本帖最後由 minimini 於 2008-1-1 14:16 編輯 ]

作者: tiger1 時間: 2008-1-1 23:33

原帖由 ryancmlam 於 2008-1-1 09:45 發表

 登錄/註冊後可看大圖

Do you mind to show us the picture of your MIP 4WD RC10 ?

Sure, here are the pictures.

作者: minimini 時間: 2008-1-2 02:05

原帖由 tiger1 於 2008-1-1 23:33 發表

 登錄/註冊後可看大圖

Sure, here are the pictures.

what a great car........

I think the performance will be even better if changed to 4WD front tyres ......

作者: tiger1 時間: 2008-1-2 07:29
Purposely keep the 2wd front tires, 'pretend pigs to eat tigers'

作者: minimini 時間: 2008-1-2 10:26

原帖由 tiger1 於 2008-1-2 07:29 發表

 登錄/註冊後可看大圖

Purposely keep the 2wd front tires, 'pretend pigs to eat tigers'

or "a wolf wearing sheep's skin" .........

作者: go2usie 時間: 2008-1-7 17:03
ryan, frankie,

saw u guys have great fun on playing RC10, especially the gold pan~
i m trying to get a good looking (and healthy) RC10 to u too.

i m looking this from ebay, any comment, and what price do u think and RC10 is reasonable? for sure i m not talking about a NIB one~

http://cgi.ebay.com/Vintage-Asso ... QrdZ1QQcmdZViewItem

作者: go2usie 時間: 2008-1-7 17:04
saw the A arms are not in white color .... does it means, arms are not original ?
seen ryan's RC10 are all white color arms~

作者: ryancmlam 時間: 2008-1-7 23:53
Bro go2usie, as far as I know, all plastic (nylon?) parts of the original RC10 should be in white. The black one should be from special version.

The one in ebay that you mentioned is the 3rd generation (same as the one that I played in TKO).

作者: peterhuang 時間: 2008-2-2 14:01
標題: rc-10
rc-10

作者: ryancmlam 時間: 2008-2-3 19:55
Is it the champion edition ?

作者: amadeus3408 時間: 2008-7-14 09:20
大哥你該不會是用煞車油洗吧?塑膠會脆化的,

作者: kins 時間: 2008-7-14 12:24

原帖由 amadeus3408 於 2008-7-14 09:20 發表

 登錄/註冊後可看大圖

大哥你該不會是用煞車油洗吧?塑膠會脆化的,

what can we use???

作者: ryancmlam 時間: 2008-7-14 18:18

原帖由 amadeus3408 於 2008-7-14 09:20 發表

 登錄/註冊後可看大圖

大哥你該不會是用煞車油洗吧?塑膠會脆化的,

Oh no. I used 煞車油. Brother amadeus3408, apart from 煞車油, any recommendation ?

作者: ryancmlam 時間: 2008-10-15 23:25
Any recommendation ? Brother amadeus3408

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)