RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: F350 OR HILUX 大家用咩控﹖ [打印本頁]

作者: VoneRRR 時間: 2007-12-29 18:01
標題: F350 OR HILUX 大家用咩控﹖
F350 OR HILUX 大家用咩控﹖

作者: bo68674 時間: 2007-12-29 18:03

4VF喽!....

作者: hzcnima 時間: 2007-12-29 18:47
4VF

作者: blackhawk 時間: 2007-12-29 19:02
Spektrum Dx6

作者: gibson 時間: 2007-12-29 19:29
I use 3PKS.

作者: 9841 時間: 2007-12-29 20:34
T 4 V F

作者: combatfung 時間: 2008-1-3 23:22

原帖由 gibson 於 2007-12-29 19:29 發表

 登錄/註冊後可看大圖

I use 3PKS.

How can it work , which button use to control the third servo ???

作者: 毒魚 時間: 2008-1-3 23:24
acnon啦= w ="

便宜= w ="""

作者: combatfung 時間: 2008-1-5 00:08
T6EXAP

作者: lichungkiu 時間: 2008-1-5 00:15
attack 4

作者: AltezzaMak 時間: 2008-1-5 10:57
Futaba 7CAP

作者: gibson 時間: 2008-1-5 12:23

原帖由 combatfung 於 2008-1-3 23:22 發表

 登錄/註冊後可看大圖

How can it work , which button use to control the third servo ???

First, you need to change the function of the 3rd channel trim to 3rd channel, and change to 3ps (three position). Then you can use the trim up down to change shift!!

作者: ramon3333 時間: 2008-1-5 17:56
標題: acoms
acoms 4ch 600元

作者: combatfung 時間: 2008-1-7 01:50

原帖由 gibson 於 2008-1-5 12:23 發表

 登錄/註冊後可看大圖

First, you need to change the function of the 3rd channel trim to 3rd channel, and change to 3ps (three position). Then you can use the trim up down to change shift!!

let me try ! THX

作者: li5115 時間: 2008-1-7 10:02

原帖由 gibson 於 2008-1-5 12:23 發表

 登錄/註冊後可看大圖

First, you need to change the function of the 3rd channel trim to 3rd channel, and change to 3ps (three position). Then you can use the trim up down to change shift!!

Do you think 3PM can do the same?

作者: gibson 時間: 2008-1-7 11:52
Not sure!!

作者: pig 時間: 2008-1-7 16:04
請問4 v f幾錢到?有冇相

作者: Petowalker 時間: 2008-1-14 02:43
Can I use Sanwa M11?

作者: peter_liu 時間: 2008-4-4 10:53
ＦＵＴＡＢＡ　３ＰＫ　也可以拉！

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)