RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 老師.. 邊道有3Racing珠叉賣? [打印本頁]

作者: sumandy 時間: 2008-1-17 14:49
標題: 老師.. 邊道有3Racing珠叉賣?
你上次介紹我果隻呢? 萬里無呀

作者: 800mah 時間: 2008-1-17 14:54
幾間都有啦~~ 惠康對面有, 鴻聲又有.

作者: ANDYMIRIAM 時間: 2008-1-17 15:00

原帖由 sumandy 於 2008-1-17 14:49 發表

 登錄/註冊後可看大圖

你上次介紹我果隻呢? 萬里無呀

我答唔答得你嫁......=_____=定你只係想老師答先....
"紅"聲好似有

作者: sumandy 時間: 2008-1-17 15:01

原帖由 800mah 於 2008-1-17 14:54 發表

 登錄/註冊後可看大圖

幾間都有啦~~ 惠康對面有, 鴻聲又有.

陳叔果間有?
聽老師講呢隻野有新舊版之分! 舊果條差到.... 新果條正D woo

作者: sumandy 時間: 2008-1-17 15:02

原帖由 ANDYMIRIAM 於 2008-1-17 15:00 發表

 登錄/註冊後可看大圖

我答唔答得你嫁......=_____=定你只係想老師答先....
"紅"聲好似有

真? 記唔記得幾錢呀?

作者: ANDYMIRIAM 時間: 2008-1-17 15:06

原帖由 sumandy 於 2008-1-17 15:02 發表

 登錄/註冊後可看大圖

真? 記唔記得幾錢呀?

你唔係kyosho 咩仲買兩條3 racing....做咩

作者: sumandy 時間: 2008-1-17 15:09

原帖由 ANDYMIRIAM 於 2008-1-17 15:06 發表

 登錄/註冊後可看大圖

你唔係kyosho 咩仲買兩條3 racing....做咩

我另一部車想整番條ma

作者: ANDYMIRIAM 時間: 2008-1-17 15:11
[quote]原帖由 sumandy 於 2008-1-17 15:09 發表

登錄/註冊後可看大圖

陳叔都好似
有啦~

作者: sumandy 時間: 2008-1-17 15:16

原帖由 ANDYMIRIAM 於 2008-1-17 15:11 發表

 登錄/註冊後可看大圖

[quote]原帖由 sumandy 於 2008-1-17 15:09 發表

登錄/註冊後可看大圖

陳叔都好似
有啦~

新版同舊版易唔易分別呢?

作者: sumandy 時間: 2008-1-17 16:36
anyone can help find this ball diff image?

作者: terencelyl7411 時間: 2008-1-17 16:41
got it

the old one ,

登錄/註冊後可看大圖

the new one ,

登錄/註冊後可看大圖

作者: sumandy 時間: 2008-1-17 16:46

原帖由 terencelyl7411 於 2008-1-17 16:41 發表

 登錄/註冊後可看大圖

got it

the old one ,

登錄/註冊後可看大圖

the new one ,

登錄/註冊後可看大圖

Hi terencely. 我公司block左3racing.. 可唔可以幫手上載上黎睇睇呢?

作者: ANDYMIRIAM 時間: 2008-1-17 17:05

原帖由 sumandy 於 2008-1-17 16:46 發表

 登錄/註冊後可看大圖

Hi terencely. 我公司block左3racing.. 可唔可以幫手上載上黎睇睇呢?

哦~~~佢係你成日上得多比公司點名BLOCK 左個網...係咪....！！！
你試好無用啦...話我地知啦...XD

作者: sumandy 時間: 2008-1-17 17:07

原帖由 ANDYMIRIAM 於 2008-1-17 17:05 發表

 登錄/註冊後可看大圖

哦~~~佢係你成日上得多比公司點名BLOCK 左個網...係咪....！！！
你試纒好無用啦...話我地知啦...XD

我信老師推介架炸

作者: terencelyl7411 時間: 2008-1-17 17:08
ball diff.

作者: sumandy 時間: 2008-1-17 17:08

原帖由 terencelyl7411 於 2008-1-17 17:06 發表

 登錄/註冊後可看大圖

上載d咩 ?????

唔駛lar.. 我用部PDA phone D/L左lar.. 死人公司連呢D車仔網都block.. ATM個網都係block左架!
唔通D鬼佬成日上去搵RC野?

作者: terencelyl7411 時間: 2008-1-17 17:08
i think 3racing is not trustable

作者: ANDYMIRIAM 時間: 2008-1-17 17:13
其實我覺得KYOSHO珠差最好....
不過尼個改板..新設計..唔知點

作者: sumandy 時間: 2008-1-17 17:33

原帖由 terencelyl7411 於 2008-1-17 17:08 發表

 登錄/註冊後可看大圖

i think 3racing is not trustable

本來我都係咁諗. 不過有個高人推介. 信心會左D law

作者: sumandy 時間: 2008-1-17 17:35

原帖由 ANDYMIRIAM 於 2008-1-17 17:13 發表

 登錄/註冊後可看大圖

其實我覺得KYOSHO珠差最好....
不過尼個改板..新設計..唔知點

一定ga la...不過如果金屬都係around $100. 點都抵過ATM!
一條買到2條半KYOSHO

作者: ANDYMIRIAM 時間: 2008-1-17 17:55

原帖由 sumandy 於 2008-1-17 17:35 發表

 登錄/註冊後可看大圖

一定ga la...不過如果金屬都係around $100. 點都抵過ATM!
一條買到2條半KYOSHO

...........掉轉左牙......
買一條KYOSHO~~買到2條半3RACING牙....

作者: 仲哥仔 時間: 2008-1-17 18:25
新噶３Ｒ珠差一定要自己磨片，换陶瓷珠，换压力轴承先够顺滑．距原装噶钢珠吾得嫁．．
同埋Ｄ齿轮系同ＫＹ噶齿轮吾配．．嘈到鬼甘．．．．

作者: henry888 時間: 2008-1-17 21:20
我唔會信其它廠, 珠叉一定係kyosho最好最順
慳一百幾十玩得唔開心, 換呢樣換果樣到最後都係要俾250最好
為咩仲要搞其它廠珠叉?

作者: sumandy 時間: 2008-1-17 21:32

全廣葦街冇貨

作者: ANDYMIRIAM 時間: 2008-1-17 23:42
kyosho 啦~~~

作者: billy86che 時間: 2008-1-18 00:10
俾心機啲整, ATM 同 3-racing 都可以好OK，可以慳一啲．　（不過下次唔好嚮標題開名，呢個forum有規定唔准)

（我都只係用鋼珠，孖星側壓一買可以買兩粒）

作者: haeconelson 時間: 2008-1-18 09:51
我都想試ATM的珠差,好似有ver2,有人用?
仲有一條係一條直過,有乜用?

作者: ANDYMIRIAM 時間: 2008-1-18 10:08

原帖由 haeconelson 於 2008-1-18 09:51 發表

 登錄/註冊後可看大圖

我都想試ATM的珠差,好似有ver2,有人用?
仲有一條係一條直過,有乜用?

你只係金屬個條定係黑色尼龍個條~~??

作者: billy86che 時間: 2008-1-18 10:43
1.Add a plastic motor shim as a cushion to the ATM diff.

2.Polishing the plates can improve the performance but do not just use a polishing cloth plus a polishing compound. You should see how "rough" the surface is and start with a right numbered sand paper. The rougher the surface is, the smaller the number of the sand paper should be used at the very beginning. (ATM needs to start with #400 while Kyosho needs no polishing) Polish the plates in running water and on a perfectly flat surface. You can use a new, thick acrylic board for car setting to provide that sought of flat surfaces. It should be small enough so that you can do the polishing under a tap.(Reserve that board only for polishing). Go down to finer sand papers until you reach about #12000 and start with polishing compound and cloth.

3.Use Associated silicon grease (red words) instead of any "diff" grease because of the small scale of the mini-Z.

4.Regular fine adjustment of the ball-diff is of vital importance. 1/10 ball-diff should usually be tight enough so that you can't make it slip with your hands but that is not the case for the mini-Z. All you need to ensure is the diff won't slip when the car runs by itself. However, once you let it slip that way, there is no return.

5. Running-in the diff needs experience. Running-in a new diff on a track with high traction, with the softest tyres, the fastast motor and the cells with the highest voltage will all lower your chance of well-breaking in your diff. Choose the opposite or at least, use your worst pack of battery.

6. My oldest diff is on the MR02 and it is at least 2 years old without any rebuilding. It is still in excellent condition and still in service. All diffs on my AWDs have never been rebuilt and they still run well. If I were to rebuild any diff, I would only replace the balls but not the plates.

See if I have missed anything you wish to know.

[ 本帖最後由 billy86che 於 2008-1-18 10:52 編輯 ]

作者: haeconelson 時間: 2008-1-18 11:34

原帖由 ANDYMIRIAM 於 2008-1-18 10:08 發表

 登錄/註冊後可看大圖

你只係金屬個條定係黑色尼龍個條~~??

金屬個條

作者: sumandy 時間: 2008-1-18 12:02

原帖由 billy86che 於 2008-1-18 10:43 發表

 登錄/註冊後可看大圖

1.Add a plastic motor shim as a cushion to the ATM diff.

2.Polishing the plates can improve the performance but do not just use a polishing cloth plus a polishing compound. You should see how "roug ...

what is "plastic motor shim"

作者: billy86che 時間: 2008-1-18 12:50

what is "plastic motor shim"

麼打蕊嗰啲膠介子

作者: sumandy 時間: 2008-1-18 15:06

原帖由 billy86che 於 2008-1-18 12:50 發表

 登錄/註冊後可看大圖

麼打蕊嗰啲膠介子

really thanks

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)