RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: TKO 用 3003 [打印本頁]

作者: move7648 時間: 2008-3-5 09:24
標題: TKO 用 3003
我部係TA02改大腳 (2.2")
請問servo用3003 OK嗎??

作者: Evo5 時間: 2008-3-5 09:42
Hm......if u dont expect it give u very good response then is ok !
I also use 3003 in my Dt02 and df03 too

作者: ice1234 時間: 2008-3-5 10:29

原帖由 Evo5 於 2008-3-5 09:42 AM 發表

 登錄/註冊後可看大圖

Hm......if u dont expect it give u very good response then is ok !
I also use 3003 in my Dt02 and df03 too

GOOD response for 3003

PS: right hand side one is extremely tuned S3003
http://www.youtube.com/watch?v=1RQGZqkEp8E

[ 本帖最後由 ice1234 於 2008-3-5 10:33 編輯 ]

作者: li5115 時間: 2008-3-5 11:01

原帖由 move7648 於 2008-3-5 09:24 發表

 登錄/註冊後可看大圖

我部係TA02改大腳 (2.2")
請問servo用3003 OK嗎??

It's OK. My M07 Big Foot is using 3003.

作者: Evo5 時間: 2008-3-5 11:13

原帖由 ice1234 於 2008-3-5 10:29 AM 發表

 登錄/註冊後可看大圖

GOOD response for 3003
PS: right hand side one is extremely tuned S3003
http://www.youtube.com/watch?v=1RQGZqkEp8E

Ohhhhh ! how u make the 3003 turn so fast ?
can u share with us ?

作者: 800mah 時間: 2008-3-5 11:13

原帖由 ice1234 於 2008-3-5 10:29 發表

 登錄/註冊後可看大圖

GOOD response for 3003
PS: right hand side one is extremely tuned S3003
http://www.youtube.com/watch?v=1RQGZqkEp8E

how do you 'tune' a S3003 ?

作者: ice1234 時間: 2008-3-5 11:15

原帖由 800mah 於 2008-3-5 11:13 AM 發表

 登錄/註冊後可看大圖

how do you 'tune' a S3003 ?

Just apply a higher voltage to servo 7.2 - 8.4V

[ 本帖最後由 ice1234 於 2008-3-5 11:22 編輯 ]

作者: Evo5 時間: 2008-3-5 11:25
How ?? can u explain ?

作者: ice1234 時間: 2008-3-5 12:02
Just directly input 7.2V to the servo red line instead of receiver one..
In other words, you only need to connect white and black colour line of servo to receiver, and red and black line of servo to 7.2V battery .

[ 本帖最後由 ice1234 於 2008-3-5 12:03 編輯 ]

作者: move7648 時間: 2008-3-5 22:50
thanks for bro comment and suggestion
i will pick a 3003 then!!

作者: MNP 時間: 2008-3-5 23:01
i m sure 3003 is the best choice for normal use, and also the value for $$$ too

作者: 光丑猶仗凡 時間: 2008-3-5 23:07
i use 3003 on both my tt01 and dt02
it ok to use at tko

作者: move7648 時間: 2008-3-5 23:14

原帖由 MNP 於 2008-3-5 11:01 PM 發表

 登錄/註冊後可看大圖

i m sure 3003 is the best choice for normal use, and also the value for $$$ too

咁又係呀
幾十蚊, 抵玩!!

作者: karl 時間: 2008-3-5 23:15
我都裝左向飯盒用，但自從訂左隻大陸995金屬servo好似好過去小小。
但部m03仲用緊去

作者: MNP 時間: 2008-3-5 23:15
i use it on my oil chicken. no problem at all. only a bit under-steer when cornering

what do you expect? $70 only

[ 本帖最後由 MNP 於 2008-3-5 23:17 編輯 ]

作者: agentjerry 時間: 2008-3-5 23:49

原帖由 MNP 於 2008-3-5 23:15 發表

 登錄/註冊後可看大圖

i use it on my oil chicken. no problem at all. only a bit under-steer when cornering what do you expect? $70 only

price below $70 ar

作者: Evo5 時間: 2008-3-6 00:00

原帖由 ice1234 於 2008-3-5 12:02 PM 發表

 登錄/註冊後可看大圖

Just directly input 7.2V to the servo red line instead of receiver one..
In other words, you only need to connect white and black colour line of servo to receiver, and red and black line of servo t ...

Hi brother i dont get u ...u said
you only need to connect white and black colour line of servo to receiver, and red and black line of servo to 7.2V battery
so where the black go ? 7.2 or receiver ?

作者: ice1234 時間: 2008-3-6 00:56

原帖由 Evo5 於 2008-3-6 12:00 AM 發表

 登錄/註冊後可看大圖

Hi brother i dont get u ...u said
you only need to connect white and black colour line of servo to receiver, and red and black line of servo to 7.2V battery
so where the black go ? 7.2 or rece ...

bOth of them .

But,for your convenient, you only need to connect servo red wire to 7.2V battery red line,so only black and white of servo wires are connected to receiver.

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)