RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: My D4 [打印本頁]

作者: joho 時間: 2008-4-4 01:15
標題: My D4
Finally finish building it up..although now they have the WCE edition...

作者: joho 時間: 2008-4-4 01:16
No.2, spend a lot of time on the body..

作者: joho 時間: 2008-4-4 01:17
Another shot from the Top...

作者: joho 時間: 2008-4-4 01:20
Try to make all the cable nice and tidy...

作者: joho 時間: 2008-4-4 01:23
Plenty of space left on the car... Now just waiting for test run on the track....

作者: joho 時間: 2008-4-4 01:23
The only complain for this car will be the shock....it's so hard to get it right..
Just hoping more people will be interest in EP buggy...

作者: crusaderlyf 時間: 2008-4-4 01:26
,good car!!
但似乎看图上你升级了61430的宽型前BUMPER,可以有效保护前臂码,另外应该是换了61499,可以用LOSI轮圈
车壳制作很有水准,可以看出花了很多心机

作者: crusaderlyf 時間: 2008-4-4 01:30
前避震架也换了吗?还是只加了螺丝垫圈增加受力面,原来版本前避震架由于凹孔位置太靠边易裂,WCE版本好了不少

作者: duncan520 時間: 2008-4-4 01:32
Very nice body dude. I'm started to work on my D4 now.....

作者: joho 時間: 2008-4-4 01:57

原帖由 crusaderlyf 於 2008-4-4 01:26 發表

 登錄/註冊後可看大圖

,good car!!
但似乎看图上你升级了61430的宽型前BUMPER,可以有效保护前臂码,另外应该是换了61499,可以用LOSI轮圈
车壳制作很有水准,可以看出花 ...

Wow Crusader! You got really good eyes... The new wider bumper is a must.. And yes, I am using the Losi rims because I have alot of stock..Also, it can interchange with my XXX-CR (rear tyres)
Yes, I am very proud about the out come of the body...And thanks for the good word!

作者: joho 時間: 2008-4-4 01:58

原帖由 duncan520 於 2008-4-4 01:32 發表

 登錄/註冊後可看大圖

Very nice body dude. I'm started to work on my D4 now.....

Do it....quick!!! I am hoping there will be more people interest in EP buggy, it's actually alot of fun, specially nowadays with brushless system...

Waiting for your D4!

作者: joho 時間: 2008-4-4 02:00

原帖由 crusaderlyf 於 2008-4-4 01:30 發表

 登錄/註冊後可看大圖

前避震架也换了吗?还是只加了螺丝垫圈增加受力面,原来版本前避震架由于凹孔位置太靠边易裂,WCE版本好了不少

No, I did not change it, all I did was flip the shock tower, and then as you say, use螺丝垫圈to spread the load. I do agree with you, the WCE is a big improvement on alot of little things..

作者: duncan520 時間: 2008-4-4 05:05

原帖由 joho 於 2008-4-4 01:58 發表

 登錄/註冊後可看大圖

Do it....quick!!! I am hoping there will be more people interest in EP buggy, it's actually alot of fun, specially nowadays with brushless system...

Waiting for your D4!

Hey joho,

There did you get the new wider bumper ??
Thanks

作者: joho 時間: 2008-4-4 16:12
You do mean where right? I think I get it from the "Cat" shop.

作者: duncan520 時間: 2008-4-4 19:58

原帖由 joho 於 2008-4-4 16:12 發表

 登錄/註冊後可看大圖

You do mean where right? I think I get it from the "Cat" shop.

yup , shuld be where..... Thanks anyway

作者: joho 時間: 2008-4-5 00:32
so how's your D4 coming around? Having fun building it???

作者: duncan520 時間: 2008-4-8 01:56

原帖由 joho 於 2008-4-5 00:32 發表

 登錄/註冊後可看大圖

so how's your D4 coming around? Having fun building it???

No..... It was bad to fix the ball diff and I'm still figure out what reason why the lock nut coming that long. It doesn't looks the same one in maunal...

Other than that. It looks kick ass !!!

Could you share what type/brand of front & rear tires you're using now?
Thanks

作者: joho 時間: 2008-4-8 17:29
Sure, but you know tyres will all depends on track condition.

Currently I am using Taper Pin from Losi front and rear. I founf out this combo always gave me a great deal of steering.. Normally I will also prepare a set of Holeshot from proline, I found this two combo mix and match will cater alot of different track condition already. The holeshot provide less steering thou..

作者: duncan520 時間: 2008-4-8 21:13

原帖由 joho 於 2008-4-8 17:29 發表

 登錄/註冊後可看大圖

Sure, but you know tyres will all depends on track condition.

Currently I am using Taper Pin from Losi front and rear. I founf out this combo always gave me a great deal of steering.. Normally I wi ...

Hey dude,

Thanks for the info !! It helps alot. I 'll be just play around at my back yard and go to TRC some day.

Did you have the same issue on the ball diff ??

作者: joho 時間: 2008-4-9 01:26
No, I read your other post which I did not have any issue at all. Let me know if you want me to take a photo of my diff, it may be a good help.

作者: duncan520 時間: 2008-4-9 02:10

原帖由 joho 於 2008-4-9 01:26 發表

 登錄/註冊後可看大圖

No, I read your other post which I did not have any issue at all. Let me know if you want me to take a photo of my diff, it may be a good help.

Here is it....

作者: duncan520 時間: 2008-4-9 02:13
the problem is that...........

作者: duncan520 時間: 2008-4-9 02:14
because of this..

作者: duncan520 時間: 2008-4-9 02:16
problem at the other side...

作者: joho 時間: 2008-4-11 00:02
Duncan, please check whether you make any mistake while you build the diff. I have check mine and it certainly does not have the nut stick out like that.. I have the same set of parts turns out perfectly..I will try to take some photo for you too. Sorry for my late reply..

作者: joho 時間: 2008-4-11 00:03
Actually I have a funny feeling that You havn't tighten the screw enough or at all...are your diff working properly like this?? Doesn't it feel too lose or anything?

作者: joho 時間: 2008-4-11 00:14
Now I think I know what's your problem after checking your photo....I think the screw is on the wrong side of the diff...Check carefully again with your menu and you will know what I mean..
Hope that can help..

作者: duncan520 時間: 2008-4-11 05:37

原帖由 joho 於 2008-4-11 00:14 發表

 登錄/註冊後可看大圖

Now I think I know what's your problem after checking your photo....I think the screw is on the wrong side of the diff...Check carefully again with your menu and you will know what I mean..
Hope that ...

I went to Jet hobbX today and fixed it . The method showing on maunal is wrong.

Ha Ha . I also have my D4 upgraded......

Thanks a million.

作者: duncan520 時間: 2008-4-11 05:42

原帖由 joho 於 2008-4-11 00:02 發表

 登錄/註冊後可看大圖

Duncan, please check whether you make any mistake while you build the diff. I have check mine and it certainly does not have the nut stick out like that.. I have the same set of parts turns out perfec ...

The guy at Jet hobbx show me the revised fm Hot bodies and I fixed it.

Did you get yourself the world champ version ??

作者: joho 時間: 2008-4-11 18:39
Oh, you should have a ammendment sheet together with the manual, I guess that's the reason you miss out on it.

No, mine was just the normal version, not the WCE, however, I am planning to get the WCE shocks, I heard from others that the WCE shocks is a major improvement then the original one on bleeding oil out...the original is really a pain to build right..

Post some photo of your car man! So more people can come here to share their D4 experience!

作者: quakequake 時間: 2008-4-11 18:45
How many R is your LRP motor?

作者: joho 時間: 2008-4-11 18:51
Depends on Track, big one I use 5.5, for smaller track, I use 6.5. The LRP you saw on the photo is a 5.5R.

作者: duncan520 時間: 2008-4-11 18:59

原帖由 joho 於 2008-4-11 18:39 發表

 登錄/註冊後可看大圖

Oh, you should have a ammendment sheet together with the manual, I guess that's the reason you miss out on it.

No, mine was just the normal version, not the WCE, however, I am planning to get the W ...

Hell yeah... Just like pain in the ass to get the shocks set up right.
I upgarded the large front bumper as you did, I think it worth to go. A rear copper sway bar, And .....
the adjustable slipper clutch set

Good stuff.

作者: joho 時間: 2008-4-11 19:07
Yes, that is good...but I tell you a small secret, the original slipper and the updated slipper behave differently, they actually affect the handling of the car more then you think, rather then just provide you adjustability from the outside.. So, keep the original one and test on it, then you will know...

Where's your car photo!!??

作者: scania...R620 時間: 2008-4-11 19:08

原帖由 joho 於 2008-4-4 01:20 發表

 登錄/註冊後可看大圖

Try to make all the cable nice and tidy...

O.................

作者: joho 時間: 2008-4-11 19:10
Oh, one more option I will suggest you to get, which is the center one-way. It's really good cause if you don't need it, you can use a pin to lock it back up, and it become normal again. I have install this right from the beginning when I build my car..
The front one-way will be a good option to keep, but not recommended, due to the fact that it will make controling the movement of the car " in-air" alot harder...

作者: duncan520 時間: 2008-4-11 19:12

原帖由 joho 於 2008-4-11 19:07 發表

 登錄/註冊後可看大圖

Yes, that is good...but I tell you a small secret, the original slipper and the updated slipper behave differently, they actually affect the handling of the car more then you think, rather then just p ...

I won't show you until it completely done.

作者: duncan520 時間: 2008-4-11 19:17

原帖由 joho 於 2008-4-11 19:10 發表

 登錄/註冊後可看大圖

Oh, one more option I will suggest you to get, which is the center one-way. It's really good cause if you don't need it, you can use a pin to lock it back up, and it become normal again. I have instal ...

Yes, I'm thinking either one of them but I'm with you on the center one way, sure will go get it next week.

作者: joho 時間: 2008-4-11 19:20
Awaiting brother.. haha

作者: joho 時間: 2008-4-11 19:21

原帖由 scania...R620 於 2008-4-11 19:08 發表

 登錄/註冊後可看大圖

O.................

I know, I should do better...that's why I said "try"...

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)