RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 慢爬大轆轉向設定 [打印本頁]

作者: ipjan 時間: 2008-5-12 21:26
標題: 慢爬大轆轉向設定
玩盡慢爬大轆...除左識用大力servo外,遙控設定都不可忽略,玩得4ws,起碼3ch先夠過引,先可以發揮架車既爬行性能,servo差少少,亦可發揮得很好...
mixing function
1,頭轆跟尾轆相反方向轉


2.頭轆跟尾轆相反方向轉  再加按比例轉向,例如:頭轉100%,尾轉30%,點解要咁set,行平路時會較2ws為好灣,如頭尾一樣轉100%(setting 1.),架車轉灣就會有點怪怪失真,好似行路鬼咁...尾轉少d,行起上來會視覺上似行2ws,尾只是作輔助轉灣

3.頭轆跟尾轆相同方向轉,架車就會打斜行,當然係用在d慢爬地方,人地爬唔到既地方,你都可能爬得到...


4.2ws,普通頭轆轉,尾轆唔轉

5.2ws,有點特別,頭轆唔轉,尾轆轉.(鏟車setting),尾轆轉向,當然係用在d慢爬地方,人地爬唔到既地方,你都可能爬得到...

[ 本帖最後由 ipjan 於 2008-5-12 21:27 編輯 ]

作者: kaho0338 時間: 2008-5-12 21:30
還有近期流行既Dig.........可原地轉
但不再是單靠2個servo..

[ 本帖最後由 kaho0338 於 2008-5-12 21:33 編輯 ]

作者: ipjan 時間: 2008-5-12 21:34

原帖由 kaho0338 於 2008-5-12 21:30 發表

 登錄/註冊後可看大圖

還有近期流行既Dig.........可原地轉
但不再是單靠2個servo..

kaho師兄
可否詳細介紹下??
小弟脫節多年...想學下d新野...
thx

作者: kaho0338 時間: 2008-5-12 21:41

原帖由 ipjan 於 2008-5-12 21:34 發表

 登錄/註冊後可看大圖

kaho師兄
可否詳細介紹下??
小弟脫節多年...想學下d新野...
thx

Demo:
http://www.youtube.com/watch?v=ALA__XEVYzw

原理:
http://www.youtube.com/watch?v=83xobuFBrA0&feature=related
http://www.youtube.com/watch?v=K7pAkILBG7Q&feature=related

作者: edison 時間: 2008-5-12 21:41
Here show you how to diy!!!

http://www.rccrawler.com/forum/showthread.php?t=101507

作者: 聶風 時間: 2008-5-12 21:55
標題: 回復 5# 的帖子
睇完 diy，都係買 kit 好 d

作者: ipjan 時間: 2008-5-12 22:36
thx kaho...
look cool like real suv function...transit power...
i think need at least 4ch with dig and 4ws...,i must do front and back dig and 4WS in my car..
because i have 9ch tx....should be fun..!!

作者: kaho0338 時間: 2008-5-12 22:42

原帖由 ipjan 於 2008-5-12 22:36 發表

 登錄/註冊後可看大圖

thx kaho...
look cool like real suv function...transit power...
i think need at least 4ch with dig and 4ws...,i must do front and back dig and 4WS in my car..
because i have 9ch tx....should be fu ...

haha...this sound crazy .......full dig install @@

作者: ipjan 時間: 2008-5-12 22:44
just my dream...
thx ur share kaho brother..

作者: kaho0338 時間: 2008-5-12 22:46

原帖由 ipjan 於 2008-5-12 22:44 發表

 登錄/註冊後可看大圖

just my dream...
thx ur share kaho brother..

you're welcome

作者: edison 時間: 2008-5-12 22:48
When I can see your full 4wd with dig coming out?

作者: ipjan 時間: 2008-5-12 22:49
想問下dig係d大廠諗出來先,定係d老外diy攪出來先啊?

作者: edison 時間: 2008-5-12 22:58
The first Dig concept was come from US DIY man.
and then some factory start to make some kit for AX10 in this year.

作者: ipjan 時間: 2008-5-12 23:01
thx edison
may i know which bl esc and motor in ur big foot?

作者: ipjan 時間: 2008-5-12 23:02
i looking CR01...outlook more like real car ...

作者: edison 時間: 2008-5-12 23:05

原帖由 ipjan 於 2008-5-12 23:01 發表

 登錄/註冊後可看大圖

thx edison
may i know which bl esc and motor in ur big foot?

ESC: Side winder
Motor HypriOh...oh...85kV

[ 本帖最後由 edison 於 2008-5-12 23:21 編輯 ]

作者: ipjan 時間: 2008-5-12 23:13
which size hyperion 30xx??

作者: ipjan 時間: 2008-5-12 23:16
hyperion 22size is 3mm shaft
30 size is 5mm shaft...but standard brush 540 is 3.17mm...

作者: kaho0338 時間: 2008-5-12 23:18

原帖由 ipjan 於 2008-5-12 23:16 發表

 登錄/註冊後可看大圖

hyperion 22size is 3mm shaft
30 size is 5mm shaft...but standard brush 540 is 3.17mm...

he mod his moto to standard 540 size....
edison is crazy player @ crawler

作者: edison 時間: 2008-5-12 23:23
My motor specifications as below!
HP-Z3025-08

http://www.aircraft-world.com/pr ... p/z30/z3025spec.htm

作者: deadmatch 時間: 2008-5-12 23:28
我都改緊部tlt....tlt真係用來改就超好玩

作者: sunfffd 時間: 2008-5-12 23:49
我決定左做死士，訂一套disconnector (dig) 番黎玩
大家有無意見

作者: ipjan 時間: 2008-5-12 23:54

原帖由 edison 於 2008-5-12 23:23 發表

 登錄/註冊後可看大圖

My motor specifications as below!
HP-Z3025-08

http://www.aircraft-world.com/pr ... p/z30/z3025spec.htm

woo..3025 size...is 40engine power for airplane
how to modifly to mount on 540 motor plate,how about pinion?just drill to 5mm ??

作者: kaho0338 時間: 2008-5-12 23:58

原帖由 sunfffd 於 2008-5-12 23:49 發表

 登錄/註冊後可看大圖

我決定左做死士，訂一套disconnector (dig) 番黎玩
大家有無意見

wait.....VF that kit have problem on it...
http://www.rccrawler.com/forum/showthread.php?t=116188

[ 本帖最後由 kaho0338 於 2008-5-13 00:00 編輯 ]

作者: sunfffd 時間: 2008-5-13 00:12

原帖由 kaho0338 於 2008-5-12 23:58 發表

 登錄/註冊後可看大圖

wait.....VF that kit have problem on it...
http://www.rccrawler.com/forum/showthread.php?t=116188

it seems like a user problem rather than the product

作者: ipjan 時間: 2008-5-13 00:34
too large servo end point and burn servo??

作者: ipjan 時間: 2008-5-13 00:38
AX10 or CR01...any suggestion for me?

作者: sunfffd 時間: 2008-5-13 00:38

原帖由 ipjan 於 2008-5-13 00:34 發表

 登錄/註冊後可看大圖

too large servo end point and burn servo??

maybe, and that guys still continues to get some new servos and burn them again

without fixing the problem first

lots of people expressed positive comments about this system
the mechanical parts are held inside a shell, to prevent dust getting in
i think i'm going to give it a shot

作者: sunfffd 時間: 2008-5-13 00:40

原帖由 ipjan 於 2008-5-13 00:38 發表

 登錄/註冊後可看大圖

AX10 or CR01...any suggestion for me?

AX10! period!

作者: ipjan 時間: 2008-5-13 00:48

原帖由 sunfffd 於 2008-5-13 00:38 發表

 登錄/註冊後可看大圖

maybe, and that guys still continues to get some new servos and burn them again
without fixing the problem first

lots of people expressed positive comments about this system
the me ...

agree...need carefully to set end point about gear shift..or DIG shift system..

作者: ipjan 時間: 2008-5-13 00:50

登錄/註冊後可看大圖

i diy frame in 2002...use clod's gear box.twin 13 turn motor

作者: sunfffd 時間: 2008-5-13 00:53

原帖由 ipjan 於 2008-5-13 00:50 發表

 登錄/註冊後可看大圖

登錄/註冊後可看大圖

i diy frame in 2002...use clod's gear box.twin 13 turn motor

join us la brother!!

http://bbs.rc-evo.com/viewthread.php?tid=80014&extra=page%3D1

作者: kaho0338 時間: 2008-5-13 00:54

原帖由 ipjan 於 2008-5-13 00:38 發表

 登錄/註冊後可看大圖

AX10 or CR01...any suggestion for me?

ax10 for sure !

作者: sunfffd 時間: 2008-5-13 00:57

原帖由 kaho0338 於 2008-5-13 00:54 發表

 登錄/註冊後可看大圖

ax10 for sure !

or get both of them

作者: ipjan 時間: 2008-5-13 01:04
SUNFFFD
join u later...i just have savage on hand now...i need buy new ep crawler
i stop play rc car long long time....

作者: ipjan 時間: 2008-5-13 01:05
AX10 can adjust wheel base....woo...very good function...hahah
simple frame and gear box design and look light weight...
easy buy spare parts in kws??

作者: ipjan 時間: 2008-5-13 01:09
AX10 can handle some fly jump action??because i like high jump too...

作者: kaho0338 時間: 2008-5-13 01:26

原帖由 ipjan 於 2008-5-13 01:09 發表

 登錄/註冊後可看大圖

AX10 can handle some fly jump action??because i like high jump too...

slow move crawler

not recommend for fly jump ....etc

作者: edison 時間: 2008-5-13 13:04
Wow, I found the front dig for real car!!

http://www.youtube.com/watch?v=CPzunPN_Ljs

作者: edison 時間: 2008-5-13 13:15
Good example for front dig in AX10
http://www.youtube.com/watch?v=UzOv5FwMoKc&feature=related

作者: sunfffd 時間: 2008-5-13 16:17

原帖由 edison 於 2008-5-13 13:15 發表

 登錄/註冊後可看大圖

Good example for front dig in AX10
http://www.youtube.com/watch?v=UzOv5FwMoKc&feature=related

Brother Edison
will you work on your own dig?

作者: edison 時間: 2008-5-13 16:19
still thinking!!!

作者: ipjan 時間: 2008-5-13 22:16

原帖由 edison 於 2008-5-13 13:15 發表

 登錄/註冊後可看大圖

Good example for front dig in AX10
http://www.youtube.com/watch?v=UzOv5FwMoKc&feature=related

very good....turn 90c

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)