RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: 我部mini-z傻左 [打印本頁]

作者: frankie1999 時間: 2008-6-3 10:31
標題: 我部mini-z傻左
我架車係第一代mini-z，放低左都有2-3年，近排想玩番，點知一power on架車，佢就好似傻左咁，不停自己轉左轉右，加速減速

有無c hing知道發生乜事？或遇過呢種情況？

Thanks 各位！

作者: jacobchu2007 時間: 2008-6-3 10:53
Set neutral point of throttle at the transmitter.

作者: frankie1999 時間: 2008-6-3 14:00

原帖由 jacobchu2007 於 2008-6-3 10:53 發表

 登錄/註冊後可看大圖

Set neutral point of throttle at the transmitter.

試左啦，點set都係好似傻左咁

作者: Aurora 時間: 2008-6-3 14:38
Check Tx and Rx crystal. Make sure the contact points are clean and they are the same set.

作者: frankie1999 時間: 2008-6-3 16:13

原帖由 Aurora 於 2008-6-3 14:38 發表

 登錄/註冊後可看大圖

Check Tx and Rx crystal. Make sure the contact points are clean and they are the same set.

yes, they are in same set.
其實有無可能係粒band壞左？會過對新band會唔會正常番？

作者: Aurora 時間: 2008-6-4 01:10

原帖由 frankie1999 於 2008-6-3 16:13 發表

 登錄/註冊後可看大圖

其實有無可能係粒band壞左？會過對新band會唔會正常番？

Yes, that is possible. And if that happens, a new set will definitely help. Also, since you bring it up, maybe we could also check the antenna is ok too?

作者: frankie1999 時間: 2008-6-4 10:43

原帖由 Aurora 於 2008-6-4 01:10 發表

 登錄/註冊後可看大圖

Yes, that is possible. And if that happens, a new set will definitely help. Also, since you bring it up, maybe we could also check the antenna is ok too?

Thanks Aurora, but how to check the antenna is workable or not?

作者: Aurora 時間: 2008-6-4 10:57
Nothing complicated, simply make sure the antenna is soldered onto the board properly.

作者: frankie1999 時間: 2008-6-4 12:42

原帖由 Aurora 於 2008-6-4 10:57 發表

 登錄/註冊後可看大圖

Nothing complicated, simply make sure the antenna is soldered onto the board properly.

要拆邊處先見到塊board？

登錄/註冊後可看大圖

作者: frankie1999 時間: 2008-6-4 15:05
剛剛出去kws買左對新band，無事啦！

對舊band點解無端端會自己壞左？

作者: lunb 時間: 2008-6-8 01:34
how much
我架車係第一代mini-z

作者: frankie1999 時間: 2008-6-10 09:59

原帖由 lunb 於 2008-6-8 01:34 發表

 登錄/註冊後可看大圖

how much
我架車係第一代mini-z

how much 你指對band？$60

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)