RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Team Losi XXX4G+ [打印本頁]

作者: Evo5 時間: 2008-6-10 15:57
標題: Team Losi XXX4G+
請問有冇師兄知到 XXXS 要改Ｄ乜變做 XXX4G+
同埋咁攪攪要洗幾多錢...唔該 !

[ 本帖最後由 Evo5 於 2008-6-10 15:58 編輯 ]

作者: m8m8 時間: 2008-6-10 17:46
rainbow兄請了解Evo5兄之問題

Evo5兄問:"請問有冇師兄知到 XXXS 要改Ｄ乜變做 XXX4G+
同埋咁攪攪要洗幾多錢...唔該 !"
但rainbow兄你好似答左買了XXX4G+後 D野喎

作者: m8m8 時間: 2008-6-11 10:29
rainbow兄,你係邊庶呀rainbow兄

rainbow兄....兄....兄....兄....兄....

rainbow兄走了........

作者: buggy 時間: 2008-6-11 13:47
我架xxxs砌完幾年都未玩過。我都想知點改呀!唔知皮帶底板洗唔西換呢？

作者: rainbow 時間: 2008-6-11 22:23
改車D錢可以買架全新車
四條油壓
头尾油壓架头尾搖比
比碼加全車推桿C
C座及轉向杯
头尾CVD狗骨
應該要加限滑
四條呔鈴(新車跟四條Losi呔鈴$270)
車殼+尾翼
价錢可以參考以下網址
http://www.losipartshouse.com/servlet/Categories

[ 本帖最後由 rainbow 於 2008-6-11 22:43 編輯 ]

作者: ftbingobingo 時間: 2008-6-11 22:32

原帖由 rainbow 於 2008-6-11 22:23 發表

 登錄/註冊後可看大圖

改車D錢可以買架全新車

Yeah, XXX-4G+好跑過孖星車好多, 一齊買啦

作者: rainbow 時間: 2008-6-11 22:46
不过我覺得Parts太少
快捷冇貨就要上網買
要等一星期
都幾煩

作者: ftbingobingo 時間: 2008-6-11 23:09
rainbow兄弟, 無零件依家野以前我都好憎

但發覺有"大代"d牌子一樣會缺貨之後, 覺得零件問題只會困擾d只玩一架車既兄弟/新手, 只要有第二架車玩, 或者一早知邊d parts要換keep定多d, 上網訂下貨根本唔成問題。
總好過玩一架齊parts, 但改到你傻, 改完都唔覺得特別好跑/好玩既車車........
依個教訓小弟喺買DB-01定XXX4G+既決擇上"奶"左野, 玩孖星依類有"大代"既車, 一樣要等PARTS, 仲要試過等超過一個月, 結果駛左好多$去改都唔夠架LOSI好跑........成件事除左當時"試新野"同"成班一齊玩"既快感之外, 駕駛/性能既樂趣真係唔係太值.......................

P.S. 純粹有感而發, 因為實在太喜愛RAINBOW兄的車車

作者: stig 時間: 2008-6-11 23:12
唔知XXX4G+ 同 ZX5 SP 邊架好跑d la..

作者: rainbow 時間: 2008-6-11 23:18
其實我貪佢唔驶点改
用底兜
及可以放LIPO电
一個字---------懶

[ 本帖最後由 rainbow 於 2008-6-11 23:28 編輯 ]

作者: rainbow 時間: 2008-6-11 23:25
我覺得係睇setting
車胎配合
电变setting
車兩架都差唔多级数
兩架都係好車

set得好,後驅都可以好快
http://hk.youtube.com/watch?v=lux7jx-2aw0
http://hk.youtube.com/watch?v=jXK3BHGYjeg

[ 本帖最後由 rainbow 於 2008-6-12 00:16 編輯 ]

作者: Evo5 時間: 2008-6-12 00:56

原帖由 ftbingobingo 於 2008-6-11 11:09 PM 發表

 登錄/註冊後可看大圖

rainbow兄弟, 無零件依家野以前我都好憎
但發覺有"大代"d牌子一樣會缺貨之後, 覺得零件問題只會困擾d只玩一架車既兄弟/新手, 只要有第二架車玩, 或者一早知邊d parts要換keep定多d, 上網訂下貨根本唔成問題。
總 ...

大代架車唔得都唔係問題...最大問題係大代裡面有條蛋散D服務態度真係不乸知所為.佢一定冇睇AndyLau個廣告..個老細請著Ｄ甘嘅火記就真係....前世....

响度趕客走甘樣.

[ 本帖最後由 Evo5 於 2008-6-12 01:02 編輯 ]

作者: Evo5 時間: 2008-6-12 00:56

原帖由 buggy 於 2008-6-11 01:47 PM 發表

 登錄/註冊後可看大圖

我架xxxs砌完幾年都未玩過。我都想知點改呀!唔知皮帶底板洗唔西換呢？

Me too !

作者: Evo5 時間: 2008-6-12 01:10

原帖由 stig 於 2008-6-11 11:12 PM 發表

 登錄/註冊後可看大圖

唔知XXX4G+ 同 ZX5 SP 邊架好跑d la..

Sure Losi la

作者: Evo5 時間: 2008-6-12 01:12

原帖由 rainbow 於 2008-6-11 10:23 PM 發表

 登錄/註冊後可看大圖

改車D錢可以買架全新車
四條油壓
头尾油壓架头尾搖比
比碼加全車推桿C
C座及轉向杯
头尾CVD狗骨
應該要加限滑
四條呔鈴(新車跟四條Losi呔鈴$270)
車殼+尾翼
价錢可以參考以下網址
http: ...

Thx ! Rainbow man ......
very helpful information.
But the parts will not cost more than the car kit right ??
New car cost $2100 wor .
Actually this design is much better than 501 i think

作者: SamsonSung 時間: 2008-6-12 14:08
I saw someone covert xxxs to xxxs"Rally", it more easy to become xxx4G
I think it will run very good.

作者: minimini 時間: 2008-6-13 02:05
我覺得呢部 X5 仲堅......不過要網上訂.......同埋價錢唔平.......

http://www.oople.com/rc/photos/reviewx5/index.html
http://www.4wdrc.com/storetech.htm
http://www.xfactoryrc.com/storekits.htm

[ 本帖最後由 minimini 於 2008-6-13 02:12 編輯 ]

作者: buggy 時間: 2008-6-13 10:07
X 5 好似好難砌咁喎。

作者: Evo5 時間: 2008-6-13 10:23

原帖由 buggy 於 2008-6-13 10:07 AM 發表

 登錄/註冊後可看大圖

X 5 好似好難砌咁喎。

好似唔多掂....重有好多DIY野....一個不小心就玩完....同埋後加野好似冇整體設計得咁完善咁

作者: minimini 時間: 2008-6-13 10:55

原帖由 Evo5 於 2008-6-13 10:23 發表

 登錄/註冊後可看大圖

好似唔多掂....重有好多DIY野....一個不小心就玩完....同埋後加野好似冇整體設計得咁完善咁

可能因為咁......所以外國只有 sponsored 車手用佢......

作者: minimini 時間: 2008-6-13 11:07
條皮帶係咪又係嗰 d "bio-degradable" 嘅衰鬼嘢 ........隔一排會自動溶化 ??......

作者: Evo5 時間: 2008-6-14 02:30
What is the different between XXX4G+ and XXX4G ???

作者: stig 時間: 2008-6-14 02:49

原帖由 Evo5 於 2008-6-14 02:30 發表

 登錄/註冊後可看大圖

What is the different between XXX4G+ and XXX4G ???

from losi web, the new Graphite Plus version, Team Losi engineers have pushed the performance envelope even further by adding super-lightweight graphite chassis components, a Kevlar spur gear, titanium nitride-coated hinge pins and a whole lot more.

作者: Evo5 時間: 2008-6-14 09:45

原帖由 stig 於 2008-6-14 02:49 AM 發表

 登錄/註冊後可看大圖

from losi web, the new Graphite Plus version, Team Losi engineers have pushed the performance envelope even further by adding super-lightweight graphite chassis components, a Kevlar spur gear, tit ...

My XXX4 has your mentioned feature but the manual just said XXX4G

作者: stig 時間: 2008-6-14 10:44
i read some report be4 and i think the main different between 2 cars is the graphite chassis, there has more graphite in it and thats why it calls G+, and i cant remember are there any others different between them, sorry about that.

作者: Evo5 時間: 2008-6-14 14:44

原帖由 stig 於 2008-6-14 10:44 AM 發表

 登錄/註冊後可看大圖

i read some report be4 and i think the main different between 2 cars is the graphite chassis, there has more graphite in it and thats why it calls G+, and i cant remember are there any others differen ...

Thx brother !
hope to see u at TKO in the furture !

作者: rk2 時間: 2008-6-14 15:37
as said in the oople web site " The 4+2 cell arrangement probably will put some people off in a similar way that saddle pack 3+3 packs already put people off." .......

作者: Evo5 時間: 2008-6-16 10:11
Rainbow man !
Have u found a problem that there are a gap in the front A arm , at the chassis side,
I have check the front arm mount, and i cant see the problem, but one side of the arm have a gap about 3mm .
Do u know wass wrong ?

作者: rainbow 時間: 2008-6-16 13:27
你是否指头比跟頭碼有虛位

作者: buggy 時間: 2008-6-16 14:47

原帖由 Evo5 於 2008-6-16 10:11 發表

 登錄/註冊後可看大圖

Rainbow man !
Have u found a problem that there are a gap in the front A arm , at the chassis side,
I have check the front arm mount, and i cant see the problem, but one side of the arm have a gap a ...

I just built my XXXG+ last week. I found there're some gaps in the front and rear arms.. moving front & back around 1 to 2mm.....and the front arms are not underloading, the dog bone is rubbing against the oring of the diff hub.....so i was thinking if the car jumps in the air then the dogbone may be scratching against the hub.....
I'm still thinking what color scheme to be used....
I'm using KO VFS 1 Reversable w/ Yokomo 15T, 22/92 ratio...is it good in general? I have not tested it on wheel yet...hehe
How about yours??

作者: Evo5 時間: 2008-6-17 11:39

原帖由 rainbow 於 2008-6-16 01:27 PM 發表

 登錄/註冊後可看大圖

你是否指头比跟頭碼有虛位

Exactly my friend ......
seems to be the manufacture problem....

作者: Evo5 時間: 2008-6-17 11:49

原帖由 buggy 於 2008-6-16 02:47 PM 發表

 登錄/註冊後可看大圖

I just built my XXXG+ last week. I found there're some gaps in the front and rear arms.. moving front & back around 1 to 2mm.....and the front arms are not underloading, the dog bone is rubbing ag ...

Hello buggy man ! I think u have the same problem as mine, but i just have only one front arm problem.
by the way does VFS1 have reverse function ??
I use to run a XXXS but not too sure about XXX4G+, and i am using brushless and my ratio is decided by the temperature !
about the paint....u can take a look at this !

作者: buggy 時間: 2008-6-17 13:59
the original tire & rim are quite tricky for me to do apply CA glue...the tire 'rib' seems quite tight on the rim. The tire cannot sit easily on the rim...anyway, need to paint the body...
Your color scheme is cool.....hope i can make some cool flames on mine too....
your rims are from DB01?
Do you find the shocks are difficult to bleed air? I think mine still have some air traped inside as it sounds like bubbling inside

.....i hate building shocks...

the tamiya shocks are easier to handle...
I forgot which version is my KO esc, it is the one with reverse function for drifting...VFS2...i'm not sure....

作者: Evo5 時間: 2008-6-17 16:01
Surely is not VFS haha !
Actually I find Losi shock is better than Tamiya wor
Haha ! More High end stuff .........
To glue tyre u need to cut some edge, i am talking about the inside ribs.
Yes DB01 goes well on Losi, Actually is tamiya copy from some US brand.
The flame is carbon like sticker.

作者: globe88 時間: 2009-5-19 11:50
Team Losi XXX4G

要幾錢呀？

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)

Powered by Discuz! X3.2