RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: (救助)用好盈無刷套裝既師兄請進 [打印本頁]

作者: kai 時間: 2008-6-22 21:40
標題: (救助)用好盈無刷套裝既師兄請進
張program card 可以set Lipo cut off 最高每cell3.4v,我用2cell電玩咪6.8v先cut off,我想問會唔會過放

作者: jasonbb 時間: 2008-6-22 21:44
應該唔會~

作者: kai 時間: 2008-6-22 21:49
我都係唔明

....

作者: lokaman 時間: 2008-6-22 21:51

原帖由 kai 於 2008-6-22 21:40 發表

 登錄/註冊後可看大圖

張program card 可以set Lipo cut off 最高每cell3.4v,我用2cell電玩咪6.8v先cut off,我想問會唔會過放

用2cell電玩咪6.8v先cut off,咪無用

作者: kai 時間: 2008-6-22 22:03
所以我先問下有無人知會唔會玩死排電

作者: kaho0338 時間: 2008-6-22 22:13

原帖由 kai 於 2008-6-22 21:40 發表

 登錄/註冊後可看大圖

張program card 可以set Lipo cut off 最高每cell3.4v,我用2cell電玩咪6.8v先cut off,我想問會唔會過放

唔會.....3.4v 每cell 重係安全, 3.3v以上就ok...

mamba max 個d default setting 係3.0v 每cell, novak default setting 係3.1v 每cell

[ 本帖最後由 kaho0338 於 2008-6-22 22:14 編輯 ]

作者: lokaman 時間: 2008-6-22 22:19

原帖由 kai 於 2008-6-22 22:03 發表

 登錄/註冊後可看大圖

所以我先問下有無人知會唔會玩死排電

唔係正常每cell不可少於3.7v咩,3.4v可經,,,,,,,,,,,,,,,,,

作者: kaho0338 時間: 2008-6-22 22:26
um... 看一看
Each cell is rated at 3.7V - This is a NOMINAL Voltage
Each cell can be charged up to 4.2V - This is MAX Voltage.
Charging over 4.2V per cell will cause damage to battery, persons or property.

Discharging.

Our cells are rated by manufacturer to discharge to Maximum of 2.75V per cell under 0.2C load. Discharging to that level at higher rates will shorten the life of the battery or damage it completely as most brushless ESC’s (electronic speed controllers) don’t have an accurate LVC (low voltage cut-off).

A common LVC point is 2.8V–3.0V per cell. This is a SAFE setting for higher discharge rates. Some brushless ESC’s are programmable and can be set up to either point & others are factory pre-set. If you discharge to 2.8V per cell the battery should “rebound” to around 3.15V or more after rest.

http://www.truerc.net/canada/shop/lipo_safety.html

[ 本帖最後由 kaho0338 於 2008-6-22 22:27 編輯 ]

作者: kai 時間: 2008-6-22 22:28
我都好似聽過每cell電不可少於3.7v先安全

作者: kaho0338 時間: 2008-6-22 22:29
還有:
You must check the pack voltage after each flight before re-charging. Do not attempt to charge any pack if the unloaded
individual cell voltages are less than 3.3V.
For example: Do not charge a 2-cell pack if below 6.6V
Do not charge a 3 cell pack if below 9.9V

http://thunderpowerrc.com/PDF/THPSafetyWarnings.pdf

作者: kaho0338 時間: 2008-6-22 22:32

原帖由 kai 於 2008-6-22 22:28 發表

 登錄/註冊後可看大圖

我都好似聽過每cell電不可少於3.7v先安全

係, 的確d人係今講, 3.7v cut係令排電耐用d及安全d.
不過我覺得3.4v 先 cut 完全冇問題, 大把大廠set 3.0-3.2 先同你cut.

作者: lokaman 時間: 2008-6-22 23:02

原帖由 kaho0338 於 2008-6-22 22:32 發表

 登錄/註冊後可看大圖

係, 的確d人係今講, 3.7v cut係令排電耐用d及安全d.
不過我覺得3.4v 先 cut 完全冇問題, 大把大廠set 3.0-3.2 先同你cut.

我想問c hing你本人試過未,我試過低過3.7v死电,thx

作者: 馮馮ymc 時間: 2008-6-22 23:09
3.2v已經ok!!電廠一般報稱,每cell不可低於3.1v,
而3.2v喺你比油果吓會drop volt而cut你電之後會回昇,
我設定3.2v cut-off,收車度有3.6v以上,冇有怕!!!

作者: kaho0338 時間: 2008-6-22 23:11

原帖由 lokaman 於 2008-6-22 23:02 發表

 登錄/註冊後可看大圖

我想問c hing你本人試過未,我試過低過3.7v死电,thx

我地一班人玩慢爬用2 cells lipo, 次次玩到3.3, 3.4 cut 都未有事....

有d人用novak 3.1先cut 都未有事....

anyway, 大把人用novak GTB, XBR, Goat Crawler Brushless System + lipo 咪又一樣3.1 先cut...又唔見成日有人話有事

Goat Crawler Brushless System:
Voltage Cut-off: 6.25 volts (when Li-Poly Cutoff Circuitry is enabled)
http://www.teamnovak.com/product ... d_system/index.html

XBR/EX SportBrushless Systems:
Voltage Cut-off 6.25 volts (when Li-Poly Cutoff Circuitry is enabled)

http://www.teamnovak.com/products/brushless/ex_systems/index.html

作者: kaho0338 時間: 2008-6-22 23:13
根本 3.4v 先cut 十分安全

作者: jj2006 時間: 2008-6-23 17:15
甘lrp tc spec有無得set?如果無,系幾v cut呢? thanks

作者: calvinsiu 時間: 2008-6-23 17:19
咁如果放電至 3.0V / CELL 呢?
我部乂電機係咁

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)