RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區

標題: Want to see the TL-01LA setup [打印本頁]

作者: SamsonSung 時間: 2008-8-18 14:10
標題: Want to see the TL-01LA setup
I want to know anyone still play TL-01?
I just buy one TL-01LA last week.
Want to see the setup
Thx.

作者: li5115 時間: 2008-8-18 17:33
Set up 無乜特別，照說明書做就得。
可調較部份有：頭尾 Camber，頭 Toe-in。
可升級和改裝部份：
快齒
碳波箱軸
碳直軸
萬向
加硬狗骨杯
頭珠差或單向
尾珠差
金屬油壓

作者: AMAT 時間: 2008-8-18 18:07
TL01.....我諗宜家已經退晒役......冇人玩.......

不過.....TL01其實都係一架唔錯O既車嚟O既.......

想睇點SET架車.....可以睇睇美國TAMIYA網站O既介紹SET UP......
http://www.tamiyausa.com/articles/feature.php?article-id=11

TL01主要個問題係重心問題.......所以換TRF油壓一定係必需咁濟......之後要落SPACER入去油壓入面,整短支油壓.
我建議你可以考慮直頭買M03專用果隻TRF油壓,因為油壓筒身較短,你就算SET短咗之後,個油壓行程都唔會太少先.
咁對你架車ROLLING反應會好好多.

另外就係配件使用啦......佢有支OPTION炭纖軸......支炭纖軸如果用到23T以上.....一段時間係會爆開......
所以如果你買到的話,記得記得,一定要係頭尾落AA膠,等O的AA膠係頭尾位滲入去....咁支中軸會襟O既.....

總之SET好架車低重心O的,架車都幾好跑......同埋記得係轆果個六角到落返2MM SPACER,咁架車會仲穩O的,
冇咁易反車.....因為TL01 SET得唔好,出O左名係易反車.

作者: SamsonSung 時間: 2008-8-18 18:23
Thank You, Amat
Very Helpful info

作者: gary 時間: 2008-8-18 21:47
原來我一路都正確玩部TL-01,唔怪得咁慢啦~~~

作者: gavl 時間: 2008-8-19 00:07
我都整緊部TL01玩黑豬，遲得post上黎。

作者: SamsonSung 時間: 2008-8-19 11:12
碳波箱軸, 萬向,珠差 & 金屬油壓 are ready.
But 偉高 sold out 快齒,
Where can fine one, Please help!

作者: li5115 時間: 2008-8-19 11:16

原帖由 SamsonSung 於 2008-8-19 11:12 發表

 登錄/註冊後可看大圖

碳波箱軸, 萬向,珠差 & 金屬油壓 are ready.
But 偉高 sold out 快齒,
Where can fine one, Please help!

試下宏記或興記。

作者: SamsonSung 時間: 2008-8-19 11:38
Thank You

作者: SamsonSung 時間: 2008-8-20 13:45
Does any one know how many degree Toe in of rear upright? TL01LA
It seem no toe in at all.
Is there any upright with toe in I can buy?
Thank.

作者: manman 時間: 2008-8-21 21:00

原帖由 AMAT 於 2008-8-18 18:07 發表

 登錄/註冊後可看大圖

TL01.....我諗宜家已經退晒役......冇人玩.......

不過.....TL01其實都係一架唔錯O既車嚟O既.......

想睇點SET架車.....可以睇睇美國TAMIYA網站O既介紹SET UP......
http://www.tamiyausa.com/articles ...

請問2MM SPACER 放落六角內側定外則呀

作者: AltezzaMak 時間: 2008-8-23 01:58

原帖由 manman 於 2008-8-21 03:00 發表

 登錄/註冊後可看大圖

請問2MM SPACER 放落六角內側定外則呀

六角外則, 即係車令同六角之間

作者: gavl 時間: 2008-8-24 01:26
想問TL01-LA既C Hub & 轉向有無同其他車共用？
另外有無覺得條roll bar 好鬆？左右"旭"?

作者: SamsonSung 時間: 2008-8-25 10:06
Hi gavl,
I have try TA04 C Hub but they don't work because the upper link don't fit.
Only thing work is go back to old short arm ( TL-01)
I don't have roll bar, don't know what to do.
Can you post you car?
I will post it later.
Thx

作者: 天照 時間: 2008-8-25 13:32

原帖由 SamsonSung 於 2008-8-20 13:45 發表

 登錄/註冊後可看大圖

Does any one know how many degree Toe in of rear upright? TL01LA
It seem no toe in at all.
Is there any upright with toe in I can buy?
Thank.

我記得係有尾TOE IN賣.....但實在太耐喇.....我都唔記得晒咁多....哈!

但佢係同TB01 O既臂OPTION件互通

作者: 天照 時間: 2008-8-25 13:34
淨係記得隻TOE IN杯係咁樣.....但唔記得係TOE IN 2定係TOE IN 1......

: 登錄/註冊後可看大圖

作者: 天照 時間: 2008-8-25 13:36
我架N咁耐O既TL01.....已經賣O左好耐........

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

作者: SamsonSung 時間: 2008-8-25 15:17
天照
Thank for posting your car
I got the idea.
I plan to race in YMC stock class.
Will you race too?
samson

作者: cyken2512 時間: 2008-8-25 21:01

原帖由天照於 2008-8-25 13:34 發表

 登錄/註冊後可看大圖

淨係記得隻TOE IN杯係咁樣.....但唔記得係TOE IN 2定係TOE IN 1......

MO3R嗰只1.5度既后HUB都好似通用喔~~~

作者: AMAT 時間: 2008-8-25 21:25

原帖由 SamsonSung 於 2008-8-25 15:17 發表

 登錄/註冊後可看大圖

天照
Thank for posting your car
I got the idea.
I plan to race in YMC stock class.
Will you race too?
samson

嚟緊果場YMC我去O左馬來西亞,未能參與~^_^

就算真係玩,我都冇TL01LA陪你玩......哈!

作者: AMAT 時間: 2008-8-25 21:26

原帖由 cyken2512 於 2008-8-25 21:01 發表

 登錄/註冊後可看大圖

MO3R嗰只1.5度既后HUB都好似通用喔~~~

TL01原裝臂可能得.
但換咗做LA臂之後,就未必一定得......

作者: SamsonSung 時間: 2008-8-26 09:58
Too bad !

作者: SamsonSung 時間: 2008-8-26 10:03
天照
I find in you photo, you use plastic upper arm link, Why?
How do you got four of them?
Thx

作者: AMAT 時間: 2008-8-26 12:15

原帖由 SamsonSung 於 2008-8-26 10:03 發表

 登錄/註冊後可看大圖

天照
I find in you photo, you use plastic upper arm link, Why?
How do you got four of them?
Thx

尾果到我唔想用推桿唧.......宜家再整我會用另一個方法嚟搞........

作者: gavl 時間: 2008-8-26 23:42

原帖由 SamsonSung 於 2008-8-25 10:06 發表

 登錄/註冊後可看大圖

Hi gavl,
I have try TA04 C Hub but they don't work because the upper link don't fit.
Only thing work is go back to old short arm ( TL-01)
I don't have roll bar, don't know what to do.
Can you post ...

Hi Bro, thank you, seems the c hub only made for the LA arm.
My TL01 LA still under construction, and will post some pics later.
Anyone can tell is the light weight chassis availiable from the market?

作者: SamsonSung 時間: 2008-8-27 10:16
Hi Gavi,
You can call 偉高模型 jimmy So, Ask him to order the chassis.
And one good thing to tell you is they have One Way unit #53200,
it fix for TL01, around $80. I will go for it.
What body shell you are use, I am useing Peugeot 306 Maxi WRC

作者: gavl 時間: 2008-9-3 18:21
here is my TL01 with LA arm

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

: 登錄/註冊後可看大圖

歡迎光臨 RC EVOLUTION - 遙控工房 - 香港RC遙控車討論區 (https://jk.rc-evo.com/xbbs/)