question about TLT-1

if i use a 2ch remote to control the TLT, but i want 4 wheel steering, is there a thing called servo Y splitter which allow me to use 1 channel controlling 2 servo?
i saw it's jut a simple splitter but dun know if it works.
anyone have tried that plz advice.
thx guys

有D控有mix fuction 唔知得唔得.

原帖由 vr2uhu 於 2006-6-7 10:36 發表
if i use a 2ch remote to control the TLT, but i want 4 wheel steering, is there a thing called servo Y splitter which allow me to use 1 channel controlling 2 servo?
i saw it's jut a simple splitte ...

係！用一條Y線就可以令兩個Servo，在相同Channel內同時轉動。

thx pal....
cani  get one in KWS? and will it be exp?
if so i will try soldering them together my self
thx

原帖由 vr2uhu 於 2006-6-7 14:37 發表
thx pal....
cani  get one in KWS? and will it be exp?
if so i will try soldering them together my self
thx

Y線廣華街一定有得賣，約幾十蚊一條。

You may need a mixer, go to the shop next to waigo that sells glider, ask the store keeper, an mixer, you can link two servos together and try try both direction, which one is four wheels turn, with a revers, it will both turn to the same direction.

I used a nine channel transmitter with servors mixing to play with this little TLT before.  Check check that shop.  

                               
登錄/註冊後可看大圖

Sorry, if using a mixer, still only can do one stun, either four wheels turn or, both wheels go to the same direction.  

I had forgotten already, you may need to try it.

Remember to get the reverse Y-harness for proper 4ws. A normal one will give you crabwalking.

a mixer is just a simple mechanical switch which chnage the red and black wire polariy of the servo or it really consist of some electronic parts? how much will it cost?
u said it will only do one stunt. either 4wheel same direction or 4 wheel turn.
that means  i have to reach the car and switch it b4 change the stunt , am i right?
plz advice

9 CH#_#
i am just thinking about a cheap 4 ch...
but there's a problem that the rignht hand side stick won't auto retract to centre point(whcih is actully for airplanes)
so may be use back a 2 channel instead.

原帖由 vr2uhu 於 2006-6-8 09:35 發表
9 CH#_#
i am just thinking about a cheap 4 ch...
but there's a problem that the rignht hand side stick won't auto retract to centre point(whcih is actully for airplanes)
so may be use back a 2 c ...

for four channel the right up down is for throttle of a plane, you can ignore it if you are not using this channel.  

Check check the manual , I think the manuel will tell you a bit more.

The mixer is a very small device that you can connect two servors in one channel. Will make a photo for you later.

A mixer is something like this.

                               
登錄/註冊後可看大圖

Photo is my mixer with a lost alarm for glider.  

Check the manual I think you may find something, pm me if any further assistance.

原帖由 gibson 於 2006-6-8 13:04 發表
A mixer is something like this.

                               
登錄/註冊後可看大圖

Photo is my mixer with a lost alarm for glider.  

Check the manual I think you may fin ...

gibson兄，我部TLT 1都有此問題...未解決..，暫用2CH控，可否教我點做你個mix fuction。謝！

sorry bro I forgot, man when getting old, the memory disappear, if something comes up in my mine, I will update you.  

I only remember to use this kind of mixer.

thx gibson.
done the installation last night,
just DIY solder the servo wire together(cheapestway)

just guess i will seldomly need the (crab walk)
so just forget the mixer
enjoying the 4WS in home last night chasing my cats around...hehe
(it's the 1st 4WS car so far i own...dun laught plz)

原帖由 Jackson 於 2006-6-8 03:09 發表
Remember to get the reverse Y-harness for proper 4ws. A normal one will give you crabwalking.

i know what u mean but not for TLT///the kit have provide a machanism for normal 4 WS eventhough using normal Y wire
thx anyway

by the way,....any body know the original servo come with old EX-5 is a meatl gear type or plastic gear type?
i found the servo very noisy when operating....thinking if it's normal or need some lube
the model is something like xx-701 in red words.
any one knows?

原帖由 vr2uhu 於 2006-6-9 09:11 發表
thx gibson.
done the installation last night,
just DIY solder the servo wire together(cheapestway)

just guess i will seldomly need the (crab walk)
so just forget the mixer
enjoying the 4 ...

Good, enjoy RC with world cup.

Cheers....

原帖由 vr2uhu 於 2006-6-9 09:21 發表
by the way,....any body know the original servo come with old EX-5 is a meatl gear type or plastic gear type?
i found the servo very noisy when operating....thinking if it's normal or need some lu ...

PLASTIC GEAR, 轉起上嚟鬼叫咁.