有無師兄知Slash用幾多度油壓油?

想問問Slash用幾多度油壓油?
同埋乜呔好走d?

唔同場地都唔同啵，用30度就最common~
Proline Caliber > bow-tie > switch > trencher 睇自己需要~　

原裝胎己經好玩啦在將軍澳有少許甩的感覺而油壓油要睇場地配合有時間來一齊飛下

回復 3# oscarchoi


    係咪冇車唔可以出聲架

回復 3# oscarchoi


師兄,我今日買左Slash 4X4,但係著發射然後著接收,初初頭2秒到個接收係正常,著住綠燈,扭軚同俾油都無問題,但係2秒過後,接收燈由綠變紅,跟住就收唔到喇,跟住我熄左發射再著,頭1秒接收燈都會變綠,1秒後又變番紅燈,玩死,乜原因呢?

呢個接收是會這樣的,
1.首先開接收按實開關由緑燈轉為紅燈然後關咗佢
2 開發射開關
3.接收開關至出現一下閃紅燈立即按發射前進制放手
4.再出現二下閃紅燈又立即按後退制放手
5.接收等下會出現緑色閃閃之後關咗接收開關
6.完成操作

以上是本人過去都發生這問題的一些意見希望能夠給與司兄一點資訊

呢個接收是會這樣的,
1.首先開接收按實開關由緑燈轉為紅燈然後關咗佢
2 開發射開關
3.接收開 ...
oscarchoi 發表於 2010-5-30 10:08

                               
登錄/註冊後可看大圖

會轉mode ga bor....

jeffip97 司兄你英文好D不如打些正確如何設定的中文字
THANK YOU

回復 8# oscarchoi


今晚試試先,唔該師兄

回復 8# oscarchoi

師兄,如果用2S鋰電,個電變要Set嗎?

新買番來要set,司兄還未完成啊

回復 11# oscarchoi

師兄,請問要setd乜?

師兄們,問題未解決,我開左發射先,然後開接收,初初接收係著綠燈,可以俾油同扭軚,但係2秒後個接收會轉紅燈,跟住就接收唔到,係乜解究呢?

師兄用咩電?叉滿未?
試下reset esc
VXL-3s Setup Programming (Calibrating your ESC and transmitter)
Read through all of the programming steps before you begin. If you get lost
during programming or receive unexpected results, simply unplug the battery,
wait a few seconds, plug the battery back in, and start over.
1. Connect a fully charged battery pack to the VXL-3s.
2. Turn on the transmitter (with the throttle at neutral).
3. Press and hold the EZ-Set button (A). The LED will first turn green and then red. Release the EZ-Set button.
4. When the LED blinks RED ONCE, pull the throttle trigger to the full throttle position and hold it there (B).
5. When the LED blinks RED TWICE, push the throttle trigger to the full reverse and hold it there (C).
6. When the LED blinks GREEN ONCE, programming is complete. The LED will then shine green or red (depending on low-voltage detection setting) indicating the VXL-3s is on and at neutral (D).

1. 叉滿電
2. 開控
3. 長按電變開關, led 會由綠轉紅, 放開開關
4. led 閃紅一下, 比盡油
5. led 閃紅2下, 比盡break
6. led 閃綠1下, done , 如果li-po cutoff 開左會長著綠, off 左會長著紅, 玩nimh 要off

開關 lipo cut-off : 開控, 開esc, 再長按電變開關, 直至有音樂