1/8 Brushless Combo

Any brother know....
Which Shop is it available?
Hobbywing 1/8 Combo:
EZRUN-150A-SD ESC & EZRUN-3674SL Motor

登錄/註冊後可看大圖

KWS 極x (x速)見有.

原帖由 hardmankam 於 2009-1-20 13:37 發表

                               
登錄/註冊後可看大圖

KWS 極x (x速)見有.

Thanks very much... I will take a look for my 1/8 conversion...

係淘寶見到,要13XX人仔.另一隻跟4465要15XX.

[ 本帖最後由 zero99 於 2009-1-20 21:47 編輯 ]

原帖由 swswsw 於 2009-1-20 21:28 發表

                               
登錄/註冊後可看大圖

Thanks very much... I will take a look for my 1/8 conversion...

swswsw c-hing.  what buggy/truggy are you converting?  i am also converting cen matrix to brushless. i will buy the 150A hobbywing as well.

原帖由 hardmankam 於 2009-1-20 23:39 發表

                               
登錄/註冊後可看大圖

swswsw c-hing.  what buggy/truggy are you converting?  i am also converting cen matrix to brushless. i will buy the 150A hobbywing as well.

I am converting my Serpent 1/8 on-road into brushless, my plan is 150A hobbywing with 3674 motor, using 6cells Lipo or A123. Originally I want to use 4465, but its diameter too big..

By the way, do you know if Mod 1 pinion gear is available there? and what T is available..

原帖由 swswsw 於 2009-1-21 00:21 發表

                               
登錄/註冊後可看大圖

I am converting my Serpent 1/8 on-road into brushless, my plan is 150A hobbywing with 3674 motor, using 6cells Lipo or A123. Originally I want to use 4465, but its diameter too big..

it will be lightning fast with onroad! but motor 3674SL (2350kv @ 22.2v = 52170rpm) may overheating wor!  I think most 1/8 brushless motor has a upper limit of around 45000 rpm. 6s is okay with 4465SL, (2000kv @22.2v = 44,400).  you may want to check with hobbywing first.

for mod 1, i dont know since i have not bought the system yet. just ask 極x.

http://www.hobbywing.com/english/ArticleShow.asp?ArticleID=437

[ 本帖最後由 hardmankam 於 2009-1-21 00:41 編輯 ]

原帖由 hardmankam 於 2009-1-21 00:36 發表

                               
登錄/註冊後可看大圖

it will be lightning fast with onroad! but motor 3674SL (2350kv @ 22.2v = 52170rpm) may overheating wor!  I think most 1/8 brushless motor has a upper limit of around 45000 rpm. 6s is okay with 44 ...

I think about this also.. so most likely..will use 6cells A123, voltage is lower and around 19.8, which gives 46530rpm and matching with normal 21 engine onroad.

原帖由 swswsw 於 2009-1-21 00:49 發表

                               
登錄/註冊後可看大圖

I think about this also.. so most likely..will use 6cells A123, voltage is lower and around 19.8, which gives 46530rpm and matching with normal 21 engine onroad.

C-Hing, where do you get A123 batteries? how do they compare with Lipo?

原帖由 hardmankam 於 2009-1-21 00:52 發表

                               
登錄/註冊後可看大圖

C-Hing, where do you get A123 batteries? how do they compare with Lipo?

in KWS helicopter shop..

Faster charging speed and safer in tough and abuse condition.....

EZRUN-150A-SD ESC  , 個 150A 電變用落 1/10 電車唔知得唔得呢 ~!

just clean all Gas parts...and preparing for brushless...

登錄/註冊後可看大圖

brushless 整唔整到  2速波箱

原帖由 manman 於 2009-1-21 01:03 發表

                               
登錄/註冊後可看大圖

EZRUN-150A-SD ESC  , 個 150A 電變用落 1/10 電車唔知得唔得呢 ~!

yes you can, BUT there is no need since 1/8 ESC size is very big compared to 1/10 ESC.

2 Speed pinion adapter 5mm bore

登錄/註冊後可看大圖

師兄，想問問依個雙速pinion同motor mount係成品定diy呀，我都想整架brushless on-road玩下

原帖由 ftbingobingo 於 2009-1-21 13:16 發表

                               
登錄/註冊後可看大圖

師兄，想問問依個雙速pinion同motor mount係成品定diy呀，我都想整架brushless on-road玩下

Order from RC-monster, one adaptors and two gears Mod 1, total around HKD300

原帖由 swswsw 於 2009-1-21 15:54 發表

                               
登錄/註冊後可看大圖

Order from RC-monster, one adaptors and two gears Mod 1, total around HKD300

THX BROTHER, I can order the motor mount from the same website?

原帖由 ftbingobingo 於 2009-1-21 19:01 發表

                               
登錄/註冊後可看大圖

THX BROTHER, I can order the motor mount from the same website?

It seems nobody making motor mount for on-road 1/8.... I got to make it myself...one point is the braking disc in serpent.. need to reduce its diameter.. or it hits the motor...