大細灣...急

呢幾日drift過左灣會好似其中一邊差速冇左咁
拆過出黎睇冇野纏住...但總係一轉左灣就會打白鴿轉
右灣就唔係好白鴿轉
有咩方法解決左灣白鴿轉呢個問題= =?
但換返快車呔左灣就會有少少推頭...會唔會係隻牙差有問題?
簡單講...依嫁快車左灣推頭,drift車左灣白鴿轉= =
(我個人覺得係其中一邊既差速出左事@@

你係o係邊到玩?左面個轆上得太緊or個彈弓位唔順.左面轆有無掂到個殼.好多原因個喎......不如上車場問下D c兄一定會幫到你

屋企......乜真係關個轆上得緊唔緊事嫁@@
冇掂轆..前邊我用京商黃彈弓...(最硬)

唔係應該用前軟後硬既咩
另外你用既咩差速先??

牙差
哈哈..我特登掉轉前後既硬度嫁

牙差
哈哈..我特登掉轉前後既硬度嫁
matthew0731 發表於 2009-4-4 21:09

                               
登錄/註冊後可看大圖

咁就正常啦,牙差個死人差速係咁......
轉番正常(前軟後硬-中軟)會易玩d ga

大細灣 is usually caused by 高低腳. Check that by putting your car on a real flat surface with battery and body shell on.

If it is not 高低腳, one more possible reason is one (or more) of the wheels is locked (or semi-locked). Check whether all wheels can run freely by detaching all wheel hubs from the chassis with the wheels still installed.

Optional metal differential covers can also lock one side (or more) of the differential(s) and cause similar problems.

今日用左2排電黎做test
test到前差速右車轆只要有少少壓力就會停下來變成一邊車轆不停轉
而一邊就停下來
完全符合我所講既問題....每當向左飄時...右邊車轆會好似停下來不足3秒..
引致飄移過程中掉頭(打白鴿轉)
如果我想換掉頭差速...不用牙差轉同別的差速好嗎?
如果不建議換別的差速..那牙差要買新的一隻嗎@@?(那會否買了一隻新的牙差又會有這個問題?

If it is so, check whether you have locked the wheels onto the bearings. Usually it is caused by using rims that are too old.

the bearings is dead already,buy a new one la

新既金屬啤令黎
不過唔係好岩size...下次都係唔好貪平= =
買返京商,pn,3racing個d好過
今次買左隻唔知咩牌子...唔係好fit位..
昨晚我換掉頭尾彈弓..轉回了頭軟尾硬...出奇地..完全沒有事了@@
不過頭用紅色..放電的那一邊會降低了....車身有點兒傾斜了
不過行到直線和過灣也沒有問題了
所以也不理它了@@

你係屋企玩；真係好難點幫你wor !因為和基本上的標準有所不同。 ;-(

其實現在己差不多解決問題了..thx各師兄幫忙