點解13 turn 好似好弱咁既？ >_<

我玩開白豬，原裝電變！(TA05) ！諗住玩得勁D！問左個 v16 pro 同 13 turn motor ！點知在屋企試車個時！以前白豬一比油就(線) 晒太咁樣向前。但係用左13 turn 後就唔得！有咩出錯左？？我用24齒 motor齒！

24 moto 齒? 今大隻個隻呢? 好肯定你齒比錯

ta05 既齒比係！  70齒/24齒 X 2.25 :1
即係6.56 : 1

13 turn 用 6.56 : 1 唔夠力？

原帖由 ko_bob 於 2007-8-12 02:03 發表

                               
登錄/註冊後可看大圖

ta05 既齒比係！  70齒/24齒 X 2.25 :1
即係6.56 : 1

用v16, 今 ratio 約去到 7.8 - 8 吧

anyway 你隻乜牌, 乜model moto? 不同牌, 不同gear ratio

[ 本帖最後由 kaho0338 於 2007-8-12 02:08 編輯 ]

原帖由 ko_bob 於 2007-8-12 02:03 發表

                               
登錄/註冊後可看大圖

13 turn 用 6.56 : 1 唔夠力？

係過火, 小心燒野

你既意思，即係  TURN 數既 motor 係咪即係越係細摟力？

turn數少既 motor  係咪即係越係細摟力？

原帖由 ko_bob 於 2007-8-12 02:23 發表

                               
登錄/註冊後可看大圖

turn數少既 motor  係咪即係越係細摟力？

rpm 高, 相對摟力低d
我都係問人

[ 本帖最後由 kaho0338 於 2007-8-12 02:31 編輯 ]

you should change ur gear ratio. like "kaho0338" says

Try the gear ratio between 7.8 to 8.35. (Which means you'll need to use the 105 tooth Spur and a pinion gear that matches it)

i run mine with a Trinity 13turn Triple Mod engine, just make sure also that ur tyres can handle it

13T试下7.3左右啦，6.5真系细佐D

我而家用70T 大齒 19T  motor 齒 係 8.2:1 ratio 但係都唔係好顛! 等冇雨先落街試清楚

13T 可以試下用6.9 - 7.1, 起圍速度都ok

我好驚！我係TA05 新手！我而家ratio 係  8.2 : 1！
架車行到盡個時！個D齒輪發出D 好高音既 we we 聲！
係咪 motor 轉數過高？我又驚燒 motor ！
轉數慢得制又會燒 esc ！快得制又傷 motor！ motor 說明書又冇講用咩 ratio 係安全！ >___<"

The only real way to test the setup is to drive ur car on the track.

The obvious "We Weee...." sounds are from the motor.

If you are really, really scare that you might blow up something  , Use a Multimeter, connect it to the motor. And check how much the current reading. (hopefully ur instruction will tell you how much current the motor chows)

Just to let you know thou, the higher ratio is used for tight tracks. as i drive around the track like a tank driver

發出wewe聲, 有可能係齒輪裝得太緊, 如果你有fd玩開車既, 最好俾佢睇下啦.